The P2P- Wireless Input Node is part of the Dene
Instruments Twin Link point-to-point system. It oers
an ideal starting point for wireless transmission of a
range of digital and analogue input signals.
101 x 23 x 120mm (3.98 x 0.91 x 4.72")
With included antenna:
150 x 23 x 146mm (5.91 x 0.91 x 5.75")
Single unit weight 154g (5.4oz),
with included antenna and plugs
Environmental conditions
Operating temp -20 to 55°C
(-4 to 131°F)
Storage temp -20 to 65°C (-4 to 149°F)
Operating humidity 0–85% non-con-
densing
Altitude 2000m (6561)
Thermocouple input
Thermocouple types & ranges
J -200 to 1000°C (-328 to 1832°F)
K -200 to 1260°C (-328 to 2300°F)
B 400 to 1800°C (752 to 3272°F)
E -200 to 700°C (-328 to 1292°F)
N -200 to 1300°C (-328 to 2372°F)
R 0 to 1700°C (32 to 3092°F)
S 0 to 1700°C (32 to 3092°F)
T -200 to 400°C (-328 to 752°F)
Input impedance >500KΩ min
TC lead resistance 100Ω max
Cold junction comp. -10 to 60°C
CJC dri <0.02°C/C typical for all
inputs
Sensor open Upscale
Accuracy 0.1% of FSO±1°C typical
RTD input
3-wire RTD Pt100 (DIN 43760:1980)
or Pt1000 (3-wire RTD standard)
Calibrated ranges -200 to 300°C (-328
to 572°F), 0.01°C res; -200 to 800°C
(-328 to 1472°F), 0.1°C res
Sensor current 0.6mA continuous
Lead resistance 10Ω/lead max recom-
mended
Sensor fail Upscale
Accuracy 0–300°C= ±0.1°C
0–800°C= ±0.3°C
Ambient dri 0.003°C/C typical
Voltage input
Ranges ±200mV, –200mV to 1V,
0–10V, 0–18V
Input impedance >500KΩ (all ranges)
Maximum over-voltage 24V DC
Accuracy 0.1% FSO max
Linearity and repeatability
0.05% FSO max
Channel separation 0.001% max
Ambient dri 0.003%/°C
Current input
Range 0/4–20mA
Input resistance 45Ω
Max over-range
Protected by PTC to 24V DC
Linearity and repeatability
0.1% FSO max
Accuracy 0.1% FSO max
Channel separation 0.001% max
Ambient dri <50ppm/°C of FS input
Response 100msec
Digital pulse
Frequency range 0–2500Hz
Sensors Open collector (NPN, PNP)
Frequency resolution 0.1Hz
Soware modes General frequency,
Flow rate, or RPM
Accuracy ±0.5%
Potentiometer input
Potentiometer input 3-wire
Potentiometer resistance Low range
(<2KΩ) or High range (>2kΩ)
Excitation voltage Variable
Field prog. zero 0–90% of span
Field prog. span 0.1–100%
Linearity and repeatability
<±0.05% FSO typical
Response time 100msec
Temperature dri <50ppm/°C
AC current sensor input
Sensor type Current transformer
(Dene Instruments ACCS-420/010)
Output (Representing 0–100% of full
scale input range)
ACCS-420 = 4–20mA DC loop powered
ACCS-010 = 0–10V DC
Power supply
ACCS-420 = Loop powered, 15–36V DC
ACCS-010 = Self powered
Accuracy 1% of full scale
Response time 250ms (10–90%)
Isolation voltage 2000V
Frequency 50–60Hz
Compliances
FCC ID: 2ACTT-1409 47 Code of Federal Regulations; Part
15 - Radio Frequency Devices; Subpart C - Intentional Radiators, including Section 15.247 - Operation in the band 2400
–2483.5MHz
AS/ANS 4268:2012Radio equipment and systems - Short
range devices - Limits and methods of measurement
ETSI EN 300 440-2, V1.4.1, 2010 Electromagnetic compat-
ibility and Radio spectrum matters (ERM); Short Range Devices
(SRD); Radio equipment to be used in the 1GHz to 40GHz frequency range; Part 2: Harmonised EN under article 3.23 of the
R&TTE Directive
EN 301 489-3, V1.6.1, 2013 Electromagnetic compatibility
and Radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 3:
Specic conditions for Short Range Devices (SRD) operating on
frequencies between 9kHz and 40GHz
Easy USB setup in minutes! Visit deneinstruments.com/toolbox
P2P Product Codes
P2P-TWIN-LINK
P2P-R
P2P-I*Point-to-Point Universal Input Node
P2P-O*Point-to-Point Output Node
* Not sold separately unless for replacement
Accessories (Sold Separately)
FCC approved 3DBi monopole antenna included with all P2P units. All
other accessories are not FCC approved.
New Zealand sales@deneinstruments.co.nz AUK +64 (9) 835-1550
South Africa sales@deneinstruments.co.za
USA (TX) sales@deneinstruments.com TX (214) 926-4950
The P2P-O Wireless Output Node is part of the Dene
Instruments Twin Link point-to-point system.
It receives wireless transmissions from the paired
Input Node (P2P-), and provides dual 4-20mA
retransmission.
›
2x 4-20mA Analogue Outputs
For simple interface to PLC's and SCADA systems
›
4x digital inputs, 2x digital outputs, and 2x relays
Configure your IOs for mimicking, alarms, and
sophisticated remote control of other equipment
›
Transmit up to 1.5km (0.9mi) Line Of Sight
›
Simple USB setup using Define ToolBox
Free download from defineinstruments.com/toolbox
P2P-O
Wireless Output Node
Specications
General
Power supply 9–36V DC, 2.5VA max
Isolation 1500V AC between power
supply and output channels
Simple soware programming using
Dene ToolBox
Connect to the P2P- Input Node
(Bridge Key required, sold separately)
Transmission
RF data rate 250Kb/s
RF frequency range 2405-2475MHz
RF receiver sensitivity -110dBm
RF transmission power +20dBm
(Optional low power setting [10dBm]
selectable in soware)
Transmission range Up to 1.5km
(0.9mi) LOS with supplied antenna
(WG-3DBI). All nodes must be set to
full power [+20dBm] for max range.
Number of RF channels 15
Up to 17 wireless nodes per mesh
Twin Link (P2P- & P2P-O) plus up to
15x Repeaters (P2P-R)
Spreading method Direct sequence
Modulation O-QPSK
Analogue Outputs
2x Analogue outputs Isolated
4–20mA or 20–4mA DC
Power supply Loop powered
Resolution 15 bits, 16000 steps
Loop drop 10V max
Linearity & repeatability 0.1% FSO
max
Accuracy 0.1% FSO max
Ambient dri 50ppm/°C FSO max
Isolation to Digital IO GND 1400Vrms
for 1min. Working voltage 125V DC
Relay Outputs
2x Relay outputs Form A relays
(5A 250V AC / 5A 30V DC)
Isolation to sensor and user input
commons 2300Vrms for 1min.
Working voltage 250V AC
Life expectancy 100K cycles min at
full load rating
Digital IO's
4x Digital inputs Max rate 1Hz.
Selectable sink/source. Suitable for
clean contacts, NPN, PNP and voltage
inputs (low input <1.4V DC, high input
1.4–30V DC)
Max continuous input 20V DC
Not isolated to power supply
common
2x Digital outputs Open drain (1A,
30V DC max)
Construction
35mm DIN rail mount casing IP20
rated. Install in a protective enclosure.
101 x 23 x 120mm (3.98 x 0.91 x 4.72")
With included antenna:
150 x 23 x 146mm (5.91 x 0.91 x 5.75")
Single unit weight 150g (5.3oz), with
included antenna and plugs
Environmental conditions
Operating temp -20 to 55°C
(-4 to 131°F)
Storage temp -20 to 65°C (-4 to 149°F)
Operating humidity 0–85% non-con-
densing
Altitude 2000m (6561)
Compliances
FCC ID: 2ACTT-1409 47 Code of Federal Regulations; Part
15 - Radio Frequency Devices; Subpart C - Intentional Radiators, including Section 15.247 - Operation in the band 2400
–2483.5MHz
AS/ANS 4268:2012Radio equipment and systems - Short
range devices - Limits and methods of measurement
P2P Product Codes
P2P-TWIN-LINK
P2P-R
P2P-I*Point-to-Point Universal Input Node
P2P-O*Point-to-Point Output Node
* Not sold separately unless for replacement
Point-to-Point paired I/O units
Point-to-Point Repeater Node
ETSI EN 300 440-2, V1.4.1, 2010 Electromagnetic compat-
ibility and Radio spectrum matters (ERM); Short Range Devices
(SRD); Radio equipment to be used in the 1GHz to 40GHz frequency range; Part 2: Harmonised EN under article 3.23 of the
R&TTE Directive
EN 301 489-3, V1.6.1, 2013 Electromagnetic compatibility
and Radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 3:
Specic conditions for Short Range Devices (SRD) operating on
frequencies between 9kHz and 40GHz
Accessories (Sold Separately)
FCC approved 3DBi monopole antenna included with all P2P units. All
other accessories are not FCC approved.
WG-8DBI8DBi Monopole antenna
(Range= 2.7km [1.7mi] LOS)
WG-AECAntenna extension cable 30cm
WG-PSUPower adaptor for 9–36V DC supply
BRIDGE-KEY
USB Bridge Key for PC programming
Set up your P2P system in minutes! Visit deneinstruments.com/toolbox
New Zealand sales@deneinstruments.co.nz AUK +64 (9) 835-1550
South Africa sales@deneinstruments.co.za
USA (TX) sales@deneinstruments.com TX (214) 926-4950
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.