QUICK START GUIDE
2K (4MP) Wireless IP Camera
IP2KCB1
For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT
THANK YOU FOR JOINING THE DEFENDER FAMILY
Help Us Make the Best Security Solutions Possible!
Leave an Honest Review in the First 6 Months and Receive
a FREE 1 Year Extended Warranty.
www.defender-usa.com/IP2KReview
For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT
WHAT’S INCLUDED
Camera Reset
Button
SD Card
Input
Camera with pre-installed
16GB SD Card
Camera Power Supply (10ft)*
*Extension Power Cable
may be required.
Mounting Hardware
Wi-Fi Camera Antenna
Ethernet Cable Shield
WHAT YOU’LL NEED FOR SET UP & INSTALLATION
• Drill
• Phillips (#2) Screwdriver
• Ladder (if required)
• Ethernet Cable (for rst time setup only depending on your Network setup)
NOTE: The IP 2K Camera will only work on 2.4 GHz frequency and is not
compatible with 5 GHz networks.
For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT
GETTING STARTED
1. Remove the red protection cap
and connect the antenna to
the camera.
2. Power on the camera by
connecting the camera cable
to the adapter.
IMPORTANT: Depending on your Network setup, you may need to connect
the camera to your modem/router using an Ethernet cable (not included) the
rst time you add the camera to the app.
3. Download the SmartSignal
mobile app. Open the app on
your device.
4. Setting up your account requires
access to your email to receive
the Verication code and is
valid for 15 minutes.
richard@account.com
NOTE: Minimize your keyboard
to continue.
For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT
IMPORTANT: Ensure your mobile device is connected to your Wi-Fi network
(2.4 GHz)– the camera and mobile device must be connected to the same
network for setup.
5. Once your account is activat-
ed, the Add Device screen will
open. Tap the + icon to add the
camera.
7. Enter your Wi-Fi Password and
click Next to continue.
6. Scan the QR Code and select
Single Camera Setup. If your
network allows, the camera will
connect over Wi-Fi directly.
8. Wait for 120 seconds for camera
to pair. NOTE: If the camera does
not connect, follow the Setup Using
Ethernet Cable.
For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT
SETUP USING ETHERNET CABLE (NOT INCLUDED)
1. Error message of Cong failed
will appear if Wi-Fi pairing fails.
Try setup using Ethernet Cable.
3. Exit the setup screen by clicking
X. Scan the QR code and select
Single Camera Setup.
2. Connect the camera to your
modem/router using an
Ethernet Cable.
4. Tap Device connected to
network link to continue.
NOTE: DO NOT tap Next.
For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT
5. Create an Admin Password
for your Device (Camera) and
Tap OK to continue.
6. Tap to select your Wi-Fi Network
from the list. NOTE: Camera will
only work on 2.4 GHz frequency.
7. Enter your Wi-Fi Password and
tap the Save icon (top of the
screen) to continue.
8. Once the camera is connected
you will see the Add successfully
screen. Tap Start Preview to
open the app.
NOTE: If you used a hard wire connection to get started, once the camera
has been connected to the app, you can disconnect the Ethernet cable and
use your Wi-Fi connection.
For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT
APP FUNCTIONALITY
Camera Name
Tap for Live View
Motion Detection
• ON (Yellow)
• OFF (Grey)
Device Selection
Alerts Received
For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT
Account Information
and Settings
MOTION ALERT
1. Tap on the camera to enter
Live View.
3. Tap to select Alarm.
2. Tap on the Setting icon to
enter to the device settings.
4. Slide the switch to turn Motion
Detect on/o.
For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT
ACTIVITY ZONE - MOTION ALERT
1. In Settings, tap to select the
Activity zones.
RECORDING SCHEDULE
1. In Settings, tap to select the
General Record Schedule.
2. Tap and drag on the grid area.
Zones highlighted in red will
detect motion.
2. Tap the Day to create a schedule
and save.
For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT
VIEW RECORDED FOOTAGE
1. Tap View history record on
the Live View screen.
3. Use the date and timeline to view your footage. Tap to zoom in/out of
the timeline.
2. Tap SD card icon to view recorded
footage.
For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT
www.DEFENDER-USA.com
Loading...