DeepSea Power & Light SeaLite Lumos 1000, SeaLite Lumos 2000 Operator's Manual

®

SeaLite

®

Lumos

Operator’s Manual

DEEPSEA

POWER & LIGHT

T: [phone]

F: [phone]

4033 Rufn Road

San Diego, CA
92123- 1817 USA

SeaLite® Lumos

Record product serial number below as it appears on the nameplate.

Serial #

Pin-out

• Postive = Pin

• Negative = Pin

• Ground = Pin

• Dimming (if applicable) = Pin

www.deepsea.com
[e-mail]

Original Instruction

REV 07/01/15

Specication Overview

* Specications subject to change without notice.

SeaLite

1.87

47.5

1.69

42.9

2.47

62.6

2.40

60.9

1.59

40.3

.59

15

6.08

154.3

7.35

186.7

1.85
47

1.00

25.4

1.00

25.4

4X 1/4-20 UNC

OR

4X M6 x 1.0

[inch]

mm

®

Lumos

Operator’s Manual

Mechanical Specications

Housing

Port

Outer Diameter

Overall Length
(w/o connector)

Weight in Air

Weight in Water

Environmental Specications

Depth Rating

Operating Temp.

Optical Specications

Colors

Lumens in Water

Color Temp/Wavelength

Beam Pattern

Electrical Specications

Lumos 2000 Lumos 1000

Input Voltage

Current

Power

10-36V DC 90-270V AC, 50/60Hz

1.10A @ 24V DC

2.65A @ 10V DC

26.5W max 32.0W max

Anodized 6013 Aluminum

Titanium (optional)

Sapphire

46.9 mm (1.85 in.)

155 mm (6.09 in)

Al housing: 530 g (1.17lbs)

1

Ti Housing: 710 g (1.56 lbs)

Al housing: 230 g (0.51 lbs)
Ti Housing: 400 g (0.88 lbs)

6,000 m (20,000 ft)

-10º C to 40º C (14º F - 104º F)

Day Light White

3

3000 typical

5000K - 6500K*

4

Flood: 85º or Spot: 32º

100-350V DC

0.27A @ 120V AC

0.13A @ 240V AC

Standard Connectors

MCBH3MP

3

2

1 = Hot (DC +)
2 = Neutral (DC -)
3 = Chassis

(High Voltage AC/DC)

1

MCBH5MP

1

5

2

1

2

4

(Low Voltage DC)

1 = DC+
2 = DC-

2

3 = Chassis
4 = Not Used

3

5= 0-5 V DC Control
(0-5V DC Control referenced
to Pin 2)

*Other connector options

are available upon request.

Dimensions

Dimming

1 Aluminum Housing, Low Voltage Driver, Flood Reector model.
2 Titanium Housing, Universal Driver, Spot Reector model.

3 Other color options available.
4 Other color temperatures available.

2

0-5V DC AC phase control (TRIAC)

variable voltage (VARIAC)

Operator’s Manual

SeaLite

®

Lumos

Table of Contents

Specification Overview 2
Table of Contents 3
Safety Symbols 4

General Notes and Warnings 4
Pre Dive Inspection 4
Post Dive Inspection 4-5
Troubleshooting 5
Flooded Light Repair 5
Limited Warranty 5
RMA Procedure for Repair 5
Appendix A: Dimming Response Curve 6
Appendix B: Driver Efficiency 9
Appendix C: LVDC Step Response Curve 11
Appendix D: Beam Patterns 14

3

SeaLite

®

Lumos

Operator’s Manual

Safety Symbol

In this operator’s manual and on the product, safety symbols are used to communicate important
safety information. This section is provided to improve understanding of these symbols.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to
avoid possible injury or death.

DANGER

! WARNING

CAUTION

NOTICE

This symbol means read the operator’s manual carefully before using the equipment. The operator’s manual contains important information
on the safe and proper operation of the equipment.

This symbol means always wear safety glasses with side shields or goggles when handling or using this equipment to reduce the risk of
eye injury.

This symbol indicates the risk of electrical shock.

DANGER indicates a hazardous situation which, if not avoided, could result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in damage to the product or bodily harm.

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE indicates information that relates to the protection of property.

General Notes and Warnings

You may run your SeaLite® Lumos in air. As the light
heats up you will notice that the output will diminish. This
is normal, and the light will return to full brightness once
it is submerged and allowed to cool down.

DANGER

When the SeaLite® Lumos is operated in air the body
may reach temperatures in excess of 65° C. These
temperatures may be enough to cause burns if the light
is handled without protective clothing.

Do not operate any high voltage electrical equipment in
or around water without using a Ground Fault Interrupt
circuit (GFI) and an isolation transformer, especially
when divers are in the water.

WARNING

Do not clean any part of the light head with any type of
alcohol.

There should be no reason to ever open the body of
your SeaLite® Lumos light. There are no user serviceable
parts inside your new underwater light. Your SeaLite®
Lumos was thoroughly pressure tested prior to leaving
the factory to confirm the integrity of the complete
assembly. Opening the housing may cause potential
problems when resealing.

Pre and Post Dive
Inspection

Check to make sure that the rear bulkhead connector is
secure before deployment.

Check the following areas for previous damage, wear or
corrosion: rear bulkhead connector, power cable, front

window.

Rinse your SeaLite® Lumos in fresh water after use in
saltwater.

DANGER

After each deployment, carefully check to make sure
the light is operational and has not flooded. If it gets
flooded, upon surfacing, the light can become internally
pressurized, which may be potentially dangerous.
Additionally, if the power remains on when the light has
partially flooded, it is possible for electrolytic generation
of an explosive mixture of hydrogen and oxygen gases.
If a light appears flooded upon removal from the water,
it should be treated as potentially dangerous. Point the
light away from persons and valuable equipment and
make sure that the power is disconnected. See the
Flooded Light Repair procedure for more information.

4

Operator’s Manual

SeaLite

®

Lumos

Troubleshooting

If the light stops working while underwater assume that

it has been flooded. See Flooded Light Repair procedure
below.

Once it has been determined that the light is not flooded,
or if it does not turn on during pre-deployment checks,
check the input power cable/inline connector to make
sure that correct voltage is being supplied, and that the
correct pinout is being used. See page 2 of this manual
for electrical specs and connector pin assignments.

If the light still does not work, return it to DSPL using the
RMA Procedure for Repair below.

Flooded Light Repair

If the light stops working while underwater, you should
assume that it has been flooded. When working on a
potentially flooded light, it is important to use appropriate
personal protective equipment to include, at a minimum,

eye and hand protection.

1. Place the light face down on a table making sure
that the connector side is facing up.

2. Slowly unscrew the connector/socket assembly to
allow any internal pressure to be equalized.

3. Once it is determined that the light is not
internally pressurized, it is recommended that
the light be returned to DeepSea Power & Light
(DSPL) for evaluation and repair using the RMA
Procedure.

RMA Procedure for Repair

Should it be necessary to return your light to the factory,
follow the procedure for the Flooded Light Repair above,
leaving the connector partially unscrewed. For warranty
and non-warranty repairs please contact DeepSea
Power & Light for a RMA number prior to returning
your item. Please have your light model number, serial
number and any other pertinent information along with
a description of the problem, on hand when you call, or
include them in a fax or e-mail. When shipping your item,
be sure that the freight is pre-paid (CODs will not be
accepted) and that the RMA number is clearly printed on
the outside of the box.

Tel: [phone]
Fax: [phone]
e-mail: [e-mail]

Limited Warranty

Seller warrants that the goods (except internal electronic
components) sold under this contract will be free from
defect in material and workmanship for a period of
one year from the date of shipment from the factory,
if they have been properly used. Internal electronic
components are warranted for 90 days from the date
of shipment from the factory, if they have been properly
used. This warranty will be limited to the repair or
replacement of parts and the necessary labor and
services required to repair the goods. IT IS EXPRESS
LY AGREED THAT THIS WARRANTY WILL BE IN LIEU
OF ALL WARRANTIES OF FITNESS AND IN LIEU
OF THE WARRANTY OF MERCHANTABILITY. This
warranty is the exclusive and only warranty to pass with
the goods under this contract. No agent, employee, or
representative of the Seller has any authority to bind
Seller to any information, representation, or warranty
concerning the goods sold under this contract, and
unless an affirmation, representation, or warranty
made by an agent, employee, or representative is
specifically included within this contract, it will not be
enforceable by Buyer. If notice of defect is given to
DeepSea Power & Light, Inc. within such 90 day or one
year warranty period, the sole obligation of DeepSea
Power & Light, Inc. shall be to furnish new or repaired
parts free of charge in exchange for parts which have
been proved defective and does not include any other
costs such as the cost of removal of the defective part,
installation, labor, or consequential damages of any
kind, the exclusive remedy being to require DeepSea
Power & Light, Inc. to furnish such new parts. Under
no circumstances shall the Buyer be entitled to recover
any incidental damages as that term is defined in
Commercial Code §2715.

All shipments should be sent to the address below:

DeepSea Power & Light
Attn: RMA ####
4033 Ruffin Road
San Diego, CA 92123-1817
U.S.A

www.deepsea.com
[e-mail]

4033 Rufn Road
San Diego, CA
92123-1817 USA

T: [phone]
F: [phone]

5

SeaLite

®

Lumos

Operator’s Manual

Appendix A

Dimming Response Curves

6

Operator’s Manual

SeaLite Lumos 1000 Phase Cut Dimming Response

100%

80%

60%

% Output

40%

20%

SeaLite

®

Lumos

% Output

0%

0° 20° 40° 60° 80° 100° 120° 140° 160° 180°

Input Phase Angle

SLL-1000 120VAC 60Hz SLL-1000 240VAC 50Hz

SeaLite Lumos 1000 Variable Voltage Dimming Response

100%

80%

60%

40%

20%

0%

0V 20V 40V 60V 80V 100V 120V 140V 160V

Input RMS Voltage

SLL-1000 120VAC 60Hz SLL-1000 High Voltage DC

7

SeaLite

100%

80%

60%

% Output

40%

20%

®

Lumos

Operator’s Manual

SeaLite Lumos 2000 Analog Dimming Response

0%

0.0V 1.0V 2.0V 3.0V 4.0V 5.0V 6.0V

Dimming Input Voltage

8

Operator’s Manual

SeaLite

®

Lumos

Appendix B

Driver Efficiency

9

SeaLite

100%

80%

60%

Efficiency

40%

20%

®

Lumos

Operator’s Manual

SeaLite Lumos 1000 Efficiency

0%

60V 110V 160V 210V 260V 310V 360V

Input RMS Voltage

SLL-1000 VAC 60Hz SLL-1000 VAC 50Hz SLL-1000 DC

SeaLite Lumos 2000 Efficiency

100%

80%

60%

Efficiency

40%

3.5

3

2.5

2

1.5

1

Current (A)

20%

0%

6V 12V 18V 24V 30V 36V

10

0.5

0

Input DC Voltage

Efficiency Input Current

Operator’s Manual

SeaLite

®

Lumos

Appendix C

Low-Voltage DC Step Response Curve

11

SeaLite

®

Lumos

Operator’s Manual

SLL-2000 DIM Input Step Response Characteristics

5V

4V

3V

2V

Control Pulse (V)

1V

0V

-10 0 10 20 30 40 50

Time (ms)

Trigger % Output

100%

90%

80%

70%

60%

50%

40%

30%

20%

10%

0%

% Output

12

Operator’s Manual

DIM Input Pulse Response: Rise Time SLL-2000 LVDC

SeaLite

®

Lumos

DIM Input Pulse Response: Fall Time SLL-2000 LVDC

13

SeaLite

®

Lumos

Operator’s Manual

Appendix D

Beam Patterns

14

Operator’s Manual

NOTE: Beam pattern data for a representative sample of the indicated product configuration only.

87

1831

5160

34

1550

2607

SeaLite

®

Lumos

Lux

Radial Lux Intensity Comparison

-90

-85

-80

6000

5000

4000

3000

2000

1000

0

85

90

-75

-70

-65

-60

-55

-50

-45

45

50

55

60

65

70

75

80

-40

40

-35

35

-30

30

-25

25

-20

20

-15

15

-10

10

Angular Distribution

90.0°

80.0°

70.0°

60.0°

50.0°

40.0°

30.0°

20.0°

-5

0

5

10.0°

0.0°

Degrees

-10.0°

-20.0°

-30.0°

-40.0°

-50.0°

-60.0°

-70.0°

-80.0°

-90.0°
0% 25% 50% 75% 100%

% Output

SeaLite Lumos Flood

SLL-2000-DW-F-A05

Lumens: Lumens:

Peak Lux: Peak Lux:

FWHP Angle: FWHP Angle:

SeaLite Lumos Spot

SLL-1000-DW-S-PV

15