TYPICAL CONNECTIONS
FUSING
Select fuses appropriately to protect the circuits connected to the device’s outputs.
Pin
Description
Comments
Recommended
Fuse Size
A7
ECU Supply
Supplies M870 CPU
3 A Max
A13
Ignition (15)
1 A Max
C1
Output Supply
Supplies Outputs QC001 (Pin C2),
QC002 (Pin C3), QC003 (Pin C4),
QC004 (Pin C5).
10 A Max
C13
Auxiliary Supply
Output
Used to Supply External Devices
Internally Protected From Overcurrent.
500 mA Max
DEEP SEA ELECTRONICS PLC
M870 Installation Instructions
These instructions are intended as a quick guide only. For complete instructions
and specifications, refer to DSE publication 057-246 M870 Operator Manual
available from www.deepseaplc.com.
NOTE: Cables / wires must be installed as indicated by the
manufacturer to prevent water entering the device. Part number of suitable
connectors are detailed in DSE publication 057-246 M870 Operator
Manual available from www.deepseaplc.com.
NOTE: Interference coupling must be avoided by correctly handling
unused cable cores.
NOTE: To ensure IP67 rating the supplied M12 protection plugs must
be installed in both the USB and Ethernet interfaces when not in use.
NOTE: To ensure the protection of the device against electrical
interference and the safe function of the device, the rear heatsink earth
point must be connected to the ground of the vehicle / machine.
NOTE: Software and associated Device Descriptors are available from
www.deepseaplc.com.
Deep Sea Electronics PLC
Tel: +44 (0)1723 890099
Fax: +44 (0)1723 893303
Email: sales@deepseaplc.com
Web: www.deepseaplc.com
Deep Sea Electronics Inc.
Tel: +1 (815) 316-8706
Fax: +1 (815) 316-8708
Email: sales@deepseausa.com
Web: www.deepseausa.com
053-187 ISSUE 1
DIMENSIONS
Description
Specification
Overall Dimensions (Height x Width x Depth)
278 mm x 171 mm x 81 mm
(10.94 ” x 6.72 ” x 3.21 ”)
Overall Weight
<2 kg
(<4.4 lb)
Mounting Type
Mounting Bolts or RAM Mount.
Fascia Mounting Holes
8 (Eight) Holes
Suitable for M5 Bolts
(0.3 “ holes)
Fascia Mounting Hole Centres
See Dimensions Diagram
Panel Cut-out
231 mm x 133 mm
(9.09 “ x 5.24 “)
Fascia Mounting Bolt Material Recommendation
Steel or Stainless Steel
Fascia Mounting Bolt Tightening Torque
1.2 Nm Maximum
(0.6 ft. lb Maximum)
RAM Mounting Holes
Suitable for M5 Bolts
(0.3 “ Holes)
RAM Mounting Hole Centres
38.1 mm x 30.2 mm
(1.50 “ x 1.19 “)
RAM Mounting Bolt Material Recommendation
Steel or Stainless Steel
RAM Mounting Bolt Tightening Torque
4 Nm Maximum
(2.95 ft. lb Maximum)
CONNECTORS, HARNESSES AND SPARE PARTS
Description
DSE
Part
Manufacturer Details
M870 Connectors
007-850
007-851
DT16-18SA-K004
DT16-18SC-K004
TE /
Deutsch
Connector Pin Crimp
(0.5 mm
2
to 1.0 mm2)
N/A
0462-201-16
TE
Connector Pin Crimp
(2 mm2)
0462-209-16
TE
M870 Connector Harness Kit
(Set of 2)
016-167
N/A
DSE
M12 to Ethernet Cable
016-160
VS-M12MS-IP20-93R-L1/2
Phoenix
M12 to USB Cable
016-161
N/A
DSE
Belden 9841 (CAN Cable)
016-030
9841
Belden
Panel Mounting Sealing
Gasket
020-579
N/A
DSE
DIMENSIONS DIAGRAM
Loading...