Deep Sea Electronics Plc DSE9 Series, DSE9130, DSE9140, DSE9150, DSE9155 Installation Instructions Manual

...
Typical Wiring Diagrams
053-049 ISSUE 13
DSE9xxx Battery Charger Installation Instructions
D E EP S E A E LECT R O N I C S
DANGER OF DEATH : LIVE PARTS exist within the DSE9xxx enclosures. The enclosure
cover must not
be removed.
Installation
The DSE9xxx battery chargers are designed to be mounted within a control panel, on the panel DIN rail utilising the integral mounts or on a chassis utilising the mounting holes. For dimension and mounting details, see overleaf. The DSE9xxx battery chargers are fit-and-forget. It can be permanently connected to the supply and the load, with no requirement to disable the charger during times of heavy load (such as engine cranking) or when in parallel with a charging alternator.
Battery suitability
The charger is factory set by DSE to suit Lead Acid batteries. The DSE91xx & DSE92xx battery chargers can be adjusted at the time of ordering to suit other battery types. The DSE947x MKII & DSE948x MKII battery chargers are configured using the DSE Configuraiton Suite to suit other battery types. Care should be taken to ensure the batteries connected to the charger are of the correct ‘technology’ to suit the setting of the charger.
Indications
The DSE9xxx Battery Chargers feature an LED indicator(s) to show the battery charger Status. (Refer to DSE publication: 057-085 DSE9xxx Series Operator Manual for further information)
Boost Mode
(Not applicable to DSE9150 12V 2A or DSE9155 30V 2A) (DSE947x & DSE948x MKII Series Only. Boost feature is controlled automatically, no external connection needed.) Boost mode is operated by connecting the BOOST terminals together (for instance with an external switch or timer circuit. This will raise the battery charger floating voltage by 0.8V DC.
Caution:- Boost mode is intended for equalisation of cells in lead acid batteries.
Dimensions and Mounting
DSE9150 12V 3A
Overall size 108mm x 101mm x 49mm
(4.25” x 3.98” x 1.91”) Weight 0.16kg Mounting type DIN rail or chassis mounting Din rail type EN 50022 35mm type only Mounting holes Suitable for M4 Mounting hole centres 91mm x 89mm
(4.25” x 3.51”) Input voltage (nominal) 110V-240V Input voltage (absolute range)
90V-250V
Charge failure relay rating
3A DC resistive, 30V maximum
Operating Temperature
-30°C to 55°C
(-22°F to 131°F)
Dimensions in mm unless stated
Connection type Screw terminal, rising clamp, no
internal spring Min cable size 0.5mm² (AWG 20) Max cable size 2.5mm² (AWG 14)
Recommended AC fuse
230V AC Input
110V AC Input
DSE9130 12V 5A charger DSE9140 12V 10A charger DSE9150 12V 3A charger DSE9155 30V 2A charger DSE9250 24V 3.7A charger DSE9255 24V 5A charger DSE9260 24V 10A charger DSE9470 MKII 24V 10A charger DSE9472 MKII 24V 5A charger DSE9480 MKII 12V 10A charger DSE9481 MKII 12V 5A charger
1.0A anti-surge
2.0A anti-surge
1.0A anti-surge
1.0A anti-surge
1.0A anti-surge
2.0A anti-surge
3.5A anti-surge
3.5A anti-surge
2.0A antisurge
2.0A anti-surge
1.0A antisurge
2.0A anti-surge
3.5A anti-surge
1.5A anti-surge
2.5A anti-surge
2.5A anti-surge
3.5A anti-surge
6.3A anti-surge
6.3A anti-surge
3.5A anti-surge
3.5A anti-surge
2.5A anti-surge
Boost not available on DSE9150 12V 3A DSE9155 30V 2A
CF not available on
DSE9150 12V 2A
DSE 947x & 948x MKII Batter y Chargers
DSE 91xx & 92xx Series
Battery Chargers
NOTE : DSE9000 series chargers are designed to be mounted with the base to a vertical surface with
the terminal strips at the bottom.
NOTE : This document is intended as a ‘quick start’ guide only. For full operating instructions and
specifications, refer to DSE publication: 057-085 DSE9xxx Series Operator Manual
Dimensions and Mounting
DSE9130 12V 5A DSE9250 24V 3.7A * DSE9155 30V 2A DSE9255 24V 5A
* This model is no longer avai lable
Overall size 136mm x 140mm x 63mm
(5.37” x 5.53” x 2.5”) Weight 0.5kg Mounting type DIN rail or chassis mounting Din rail type EN 50022 35mm type only Mounting holes Suitable for M4 Mounting hole centres
119.36mm x 128.36mm
(4.7” x 5.05”) Input voltage (nominal)
DSE9250-001 24V 3.7A
DSE9250-002 24V 3.7A
DSE9130 12V 5A
DSE9255 24V 5A
110V-240V 110V-277V 110V-277V
110V-277V Input voltage (absolute range)
DSE9250-001 24V 3.7A DSE9250-002 24V 3.7A DSE9130 12V 5A DSE9255 24V 5A
90V-265V
90V-305V
90V-305V
90V-305V Charge failure relay rating
3A DC resistive, 30V maximum
Operating Temperature
-30
°
C to 55°C
(-22°F to 131°F)
Dimensions in mm unless stated
Dimensions and Mounting
DSE9140 12V 10A DSE9260 24V 10A
Overall size 152mm x 188mm x 62mm
(6” x 7.4”x 2.44”) Weight DSE9140 12V 10A DSE9260 24V 10A
0.75kg
0.85kg Mounting type DIN rail or chassis mounting Din rail type EN 50022 35mm type only Mounting holes Suitable for M4 Mounting hole centres 142mm x 128mm
(5.59” x 5.0”) Input voltage (nominal) 110V-277V Input voltage (absolute range)
90V-305V
Charge failure relay rating 3A DC resistive 30V Maximum Operating Temperature
-30
°
C to 55°C
(-22°F to 131°F)
Dimensions in mm unless stated
Deep Sea Electronics Plc.
Tel:+44 (0)1723 890099
Fax: +44 (0)1723 893303
Email: sales@deepseaplc.c om
Web: www.deepseaplc.com
Deep Sea Electronics Inc.
Phone: +1 (815) 316-8706
Fax: +1 (815) 316- 8708
Email: sales@deepseaus a.com
Web: www.deepseausa.com
Dimensions and Mounting
Intelligent Battery Chargers
DSE9481 MKII 12V 5A
DSE9472 MKII 24V 5A
DSE9480 MKII 12V 10A
DSE9470 MKII 24V 10A
Overall size 205mm x 135mm x 80mm
(8.1” x 5.3” x 3.1”) Weight DSE9470 MKII DSE9472/80/81 MKII
0.78kg
0.7kg Mounting type DIN rail or chassis mounting Din rail type EN 50022 35mm type only Mounting holes Suitable for M4 Mounting hole centres 190mm x 120mm
(7.5” x 4.7”) Input voltage (nominal) 110V-277V Input voltage (absolute range)
95V-305V
Charge failure relay rating 3A DC resistive
30V maximum Operating Temperature
-30
°
C to 85°C with de-rating
(-22°F to 185°F) Optional Temperature Sensor
NTC connections for PT1000
sensor only Communications RS485 PC connection (USB) To enable PC Configuration
Dimensions in mm unless stated
6in
2.44in
7.4 in
Loading...