Deep Sea Electronics Plc 8620, 8610 Installation Instructions And Instructions For Use

TYPICAL

WIRING DIAGRAM

A larger diagram is available in the operators manual.

Deep Sea Electronics Plc.

Tel:[phone]

Fax: [phone]

LO CALL (from UK BT landlines) :

Telephone [phone]

Email: [e-mail]

Web:

www.deepseaplc.

com

Deep Sea Electronics inc.

Phone: [phone]-

8706

Fax: [phone]-

8708

TOLL FREE (USA only) : Tel: [phone]

Email: [e-mail]

Web: www.deepseausa.com

DIMENSIONS AND MOUNTING

For flat surface mounting in a Type 1 enclosure to meet UL requirements

DIMENSIONS

240.0mm x 181.1mm x 41.7mm (9.4” x 7.1” x 1.6”)

PANEL CUTOUT

:

220mm x 160mm (8.7” x 6.3”)

ACCESSING THE FRONT PANEL CONFIGURATION EDITOR.

•

Ensure the engine is at rest and the module is in STOP mode by pressing the Stop/Reset

• Press the Stop/Reset and Info

buttons simultaneously.

•

If a module security PIN has been set, the PIN number request is then

shown :

• Press the button the first digit will flash

to

• Press

(up) or

(down to

adjust

• Press (right)

when the first digit is c

show ‘#’ for security.

•

Repeat this process for the other digits o

f the PIN number. You can press

back to adjust one of the previous digits.

•

When

is pressed after editing the final

not correct, you must re-enter the PIN.

•

If the PIN has been successfully entered (or the module PIN has not been

enabled), the editor is displayed :

EDI

TING A PARAMETER

• Enter the editor as described above.

• Press the or

to cycle to the section you wish to view/change.

to cycle to the parameter

within the section you have chosen.

• To edit the parameter, press

to enter edit mode. The parameter begins to flash to indicate that

you are editing the value.

• Press the up or down buttons to

change the parameter to the required value.

• Press to save the value

. The parameter

• To exit the editor at any time, press and hold the

DEE P S E A E L E C T R O N I C S

86 2

0 IN ST AL L AT IO N IN S TR UC T IO NS

NOTE: When the editor is visible, it is automatically exited after 5

NOTE: When the editor is visible, it is automatically exited after 5 NOTE: When the editor is visible, it is automatically exited after 5

NOTE: When the editor is visible, it is automatically exited after 5

ensure security.

ensure security.ensure security.

ensure security.

NOTE:

NOTE: NOTE:

NOTE:

The PIN number is automatically reset when the editor is exited (manually or

The PIN number is automatically reset when the editor is exited (manually or The PIN number is automatically reset when the editor is exited (manually or

The PIN number is automatically reset when the editor is exited (manually or

automatically) to ensure security.

automatically) to ensure security.automatically) to ensure security.

automatically) to ensure security.

NOTE:

NOTE: NOTE:

NOTE:

More comprehensive module configuration is possible using the

More comprehensive module configuration is possible using the More comprehensive module configuration is possible using the

More comprehensive module configuration is possible using the

configurati

configuraticonfigurati

configuration software

on softwareon software

on software.

. .

.

Please contact us for further details

Please contact us for further detailsPlease contact us for further details

Please contact us for further details

NOTE: The contents of the tables overleaf may differ depending on the actual module

NOTE: The contents of the tables overleaf may differ depending on the actual module NOTE: The contents of the tables overleaf may differ depending on the actual module

NOTE: The contents of the tables overleaf may differ depending on the actual module

configuration.

configuration. configuration.

configuration.

button.

enable the pin to be entered.

it to the correct value)

(left) if you need to move

Then press

or

ceases flashing to indicate that it has been saved.

or button.

053-129

ISSUE 1

minutes of inactivity to

minutes of inactivity to minutes of inactivity to

minutes of inactivity to

86

8686

86xx series PC

xx series PC xx series PC

xx series PC

ADJUSTABLE PARAMETERS

Front Panel Configuration Editor

Section Parameter as shown on display Values

Display

Contrast 53%
Language

English, others.

Current Date and Time

hh:mm

Timers

LCD Page Timer

5m

Scroll Delay

2

s

Engine Pre Heat Timer

0s

Engine Crank Duration

10s

Engine Crank Rest Time

10s

Engine Safety On Delay

10s

Engine Smoke Limiting

0s

Engine Smoke Limiting Off

0s

Engine Warm Up Time

0s

Engine Cool Down Time

1m

Engine Speed Overshoot Delay

0s

Engine Failed To Stop

30s

Battery Under Voltage Warning Delay

1m

Battery Over Voltage Warning Delay

1m

Return Delay

30s

Generator Transient Delay

0s

Mains Transient Delay

2s

Mains transfer time

0.7s

Mains

Mains Under Voltage Alarm

184V

Mains Over Voltage Alarm

277V

Mains Under Frequency Alarm

45Hz

Mains over Frequency Alarm

55Hz

Mains Transient Delay

2s

CT Primary

600A

CT Secondary

5A

Mains KW Rating

345kW

Mains KVar Rating

258kW

Generator

Under Voltage Shutdown

184v

Under Voltage Pre-Alarm

196v

Nominal Voltage 230v
Over Voltage Pre-Alarm 265v
Over Voltage Shutdown 277v
Under Frequency Shutdown 40Hz
Under Frequency Pre-Alarm 42Hz
Nominal frequency 50Hz
Over Frequency Pre-Alarm 54Hz
Over Frequency Shutdown 57Hz
Full Load Rating 500A
kW Overload Trip 100%
Delayed Over current Active
Delayed Over Current 100%
AC System 3 Phase 4 Wire
CT Primary 600A Power Cycle After Exit
CT Secondary 5A Power Cycle After Exit
Short Circuit Trip 200%
Earth CT Primary 500A
Earth Fault Trip Active
Earth Fault Trip 10%
Transient Delay 0s
Gen Reverse Power Delay 2s
Full kW rating 345kW
Full kVAr rating 258kVAr
Load Ramp Rate 3%
Gen Reverse Power 35kW
Insufficient Capacity Delay 1s
Insufficient Capacity action None
Reactive Load CTL mode VAr fixed export
Load Parallel Power 50%
Load Power Factor 1.00pf 0 KVAr 0%

Engine

Oil Pressure Low shutdown 1.03bar
Oil Pressure Low Pre-Alarm 1.24bar
Coolant Temp High Pre-Alarm 90ºC
Coolant Temp High Electrical Trip 92ºC (When Enabled)
Coolant Temp High Shutdown 95ºC
Start Delay Off load 5s
Start Delay on load 5s
Start Delay Telemetry 5s
Pre Heat Timer 0s
Crank Duration 10s
Crank rest Time 10s
Safety On Delay 10s
Smoke Limiting 0s
Smoke limiting off 0s
Warm Up Time 0s
Cool Down Time 1m
Speed Overshoot Delay 0s
Speed Overshoot 0%
Fail To Stop Delay 30s
Battery Under Volts Warning Active
Battery Under Volts Warning Delay 1m

Continued Overleaf

Front Panel

Configuration Editor (continued)

Section Parameter as shown on display Values

Engine (Continued)

Battery Under Volts Warning 10v
Battery Over Volts Warning Active
Battery Over Volts Warning Delay 1m
Battery Over Volts Warning 30v
Charge Alternator Failure Warning Active
Charge Alternator Failure Warning

6.0v

Charge Alternator Warning Delay

5s

Charge Alternator Failure Shutdown

Ina

ctive

Charge Alternator Failure Shutdown

4.0v (When Enabled)

Charge Alternator Shutdown Delay

5s (When Enabled)

Droop %

Active, Inactive. Electronic engines only when
droop is enabled.

Scheduler

Scheduler

Active, Inactive

Schedule On Load

Active , Inactive (Only Available When
Scheduler Is Active)

Schedule Period

Weekly, Monthly (Only Available When
Scheduler Is Active)

Schedule Time & Date Selection (1-16)

Press to begin editing then or

when selecting the different

parameters in the scheduler.

ACCESSING THE ‘RUNNING’ CONFIGURATION EDITOR

• The ‘running’ editor can be entered while the engine is running. All protections remain active if the
engine is running while the running editor is entered.

• Press and hold the button to enter the running editor.

ADJUSTABLE PARAMETERS (Running editor)

• Enter the editor as described above.

• Press the up or down buttons to cycle to the section you wish to view/change.

• To Edit the parameter press the button to enter edit mode. The parameter begins to flash to

indicate that you are editing the value.

• Press the up

or down

buttons to change the parameter to the required value.

• Press the button to save the value. The parameter ceases flashing to indicate that it has been
saved.

• To exit the editor at any time , press and hold the button.

Running Editor

Section Parameter as shown on display Factory Settings

DISPLAY Contrast 53%

Language

English

Load Power factor

0-100%

(0)

Load parallel power

0-100% (50)

)

Commissioning screens

Inactive

,

Active

Override starting alarms

Inactive, Active

Voltage adjust (manual mode only engine running breaker open)

0-100 % (0)

Frequency adjust (manual mode only engine running breaker open)

0-100 % (0)

Auxiliary Mains Fail Out of sync reset

Inactive Active

Mains decoupling test mode (Stop mode only)

Inactive Active