DeDietrich AWHP-2 MIT-IN-2 iSystem, MIT-IN-2/E, MIT-IN-2/H Installation And Service Manual
Export
HPI EVOLUTION
EN
Air / water heat pump
AWHP-2 MIT-IN-2 iSystem
Installation and
Service Manual
7616371-001-04
Declaration of conformity
The device complies with the standard type described in the EG
declaration of conformity. It was manufactured and commissioned in
accordance with European directives.
The original declaration of conformity is available from the
manufacturer.
C004793-A
Contents
1 Introduction ................................................................................................6
1.1 Symbols used .......................................................6
1.1.1 Symbols used in the manual ...................................6
1.1.2 Symbols used on the equipment .............................6
1.2 Abbreviations ........................................................7
1.3 Liabilities ...............................................................7
1.3.1 Manufacturer’s liability .............................................7
1.3.2 Installer’s liability .....................................................7
1.4 Homologations ......................................................8
1.4.1 Certifications ...........................................................8
2 Safety instructions and recommendations ..............................................9
2.1 Safety instructions ...............................................9
2.2 Recommendations ................................................9
3 Technical description ..............................................................................11
3.1 General description ............................................11
3.2 Main parts (Indoor module) ...............................11
3.2.1 MIT-IN-2/H ............................................................11
3.2.2 MIT-IN-2/E .............................................................12
3.3 Operating principle .............................................12
3.3.1 General .................................................................12
3.3.2 Skeleton Diagrams ................................................13
3.3.3 Pressure available .................................................14
3.4 Technical specifications ....................................14
3.4.1 Electricity supply ...................................................14
3.4.2 Heat pump .............................................................15
3.4.3 Sensor characteristics ...........................................16
4 Installation ................................................................................................17
4.1 Regulations governing installation ...................17
4.2 Package list .........................................................17
4.2.1 Standard delivery ..................................................17
4.2.2 Accessories ...........................................................18
4.3 Type plate ............................................................19
4.3.1 Outdoor unit ..........................................................19
4.3.2 Indoor module .......................................................19
25/06/2014 - 7616371-001-04
1
4.4 Installing the outdoor module ...........................20
4.4.1 Positioning of the appliance ..................................20
4.4.2 Main dimensions ...................................................22
4.4.3 Locating the outside module ................................26
4.5 Installing the indoor module ..............................27
4.5.1 Positioning of the appliance ..................................27
4.5.2 Main dimensions ...................................................27
4.5.3 Assembly of the indoor module ............................28
4.6 Installing the outside sensor .............................29
4.6.1 Choice of the location ............................................29
4.6.2 Connecting the outside sensor ..............................29
4.7 Combination with a DHW tank ...........................30
4.8 Installing the refrigerant piping .........................30
4.8.1 Installing the pipes ................................................30
4.8.2 Water tightness test ..............................................35
4.8.3 Evacuation ............................................................35
4.8.4 Opening the valves ...............................................35
4.8.5 Adding refrigerant ..................................................36
4.9 Hydraulic connections .......................................36
4.9.1 Flushing the system ..............................................36
4.9.2 Connection of the heating circuit ...........................37
4.9.3 Hydraulic connection diagrams .............................37
4.10 Filling the heating system ..................................40
4.10.1 Water treatment in the heating circuit ...................40
4.10.2 Filling the system ..................................................42
4.11 Electrical connections ........................................42
4.11.1 Recommendations ................................................42
4.11.2 Recommended cable cross section ......................43
4.11.3 Accessing the connection terminal blocks ............44
4.11.4 Position of the PCBs .............................................46
4.11.5 Location of the fuse ...............................................47
4.11.6 Connecting the outdoor module ............................47
4.11.7 Connecting the communication cable between the
inside and outside modules ...................................47
4.11.8 Description of the terminal block on the inside
module ..................................................................48
4.11.9 Connecting the mains supply to the inside
module ..................................................................49
4.11.10 Connecting the electrical back-up to the inside
module ..................................................................49
4.11.11 Connecting the hydraulic auxilary on the inside
module ..................................................................51
4.11.12 Connection example for a system with hydraulic back-
up ..........................................................................52
4.11.13 Connection example for a system with electrical back-
up ..........................................................................57
4.11.14 Connection example in cooling mode ...................59
4.11.15 Pool connection .....................................................61
4.11.16 Connecting the options .........................................63
4.11.17 Connecting the "energy metering" option ..............64
4.11.18 Connection in cascade ..........................................67
Contents
25/06/2014 - 7616371-001-04
2
4.11.19 Connection example in power cut off EVU ............69
4.12 Electrical principle diagram ...............................71
4.12.1 Legend ..................................................................71
4.12.2 Hydraulic additional heating ..................................73
4.12.3 Electrical back-up ..................................................74
5 Commissioning ........................................................................................75
5.1 Control panel .......................................................75
5.1.1 Description of the keys ..........................................75
5.1.2 Description of the display ......................................76
5.1.3 Access to the various browsing levels ..................79
5.1.4 Browsing in the menus ..........................................80
5.2 Check points before commissioning ................81
5.2.1 Hydraulic connections ...........................................81
5.2.2 Electrical connection .............................................81
5.3 Checklist for commissioning (HP) ....................82
5.4 Putting the appliance into operation ................83
5.5 Checks and adjustments after
commissioning ...................................................84
5.5.1 Displaying the parameters in extended
mode .....................................................................84
5.5.2 Setting the heating pump speed on the heat
pump .....................................................................84
5.5.3 Setting the flow rate threshold ...............................85
5.5.4 Setting the parameters specific to the
installation .............................................................86
5.5.5 Naming the circuits and generators ......................91
5.5.6 Setting the heating curve ......................................92
5.5.7 Setting the speed of the heating pump on the inside
module ..................................................................94
5.6 Reading out measured values ...........................94
5.7 Changing the settings ........................................96
5.7.1 Language selection ...............................................96
5.7.2 Calibrating the sensors .........................................96
5.7.3 Professional settings .............................................98
5.7.4 Configuring the network ......................................109
5.7.5 Return to the factory settings ..............................112
25/06/2014 - 7616371-001-04
3
6 Switching off the appliance ...................................................................113
6.1 Installation shutdown .......................................113
6.2 Turning on the antifreeze function ..................113
7 Checking and maintenance ...................................................................114
7.1 General instructions .........................................114
7.2 Maintenance operations to be performed ......114
7.3 Cleaning the 400 µm filter ................................114
7.4 Customising maintenance ...............................115
7.4.1 Maintenance message ........................................115
7.4.2 Contact details of the professional for After Sales
Support ................................................................116
8 Troubleshooting .....................................................................................118
8.1 Anti-hunting ......................................................118
8.2 Messages ...........................................................118
8.3 Message history ................................................120
8.4 Faults (Code type Lxx or Dxx) .........................121
8.4.1 Deletion of sensors from the memory in the
PCB .....................................................................124
8.5 Failure history ...................................................125
8.6 Parameter and input/output check (mode
tests) ..................................................................125
9 Spare parts ..............................................................................................131
9.1 General ..............................................................131
9.2 Spare parts ........................................................132
9.2.1 Outdoor unit 4 and 6 kW .....................................132
9.2.2 Outdoor unit 8 kW ...............................................135
9.2.3 Outdoor unit 11 and 16 kW .................................138
9.2.4 Outdoor unit 22 and 27 kW .................................143
9.2.5 Indoor module .....................................................147
Contents
25/06/2014 - 7616371-001-04
4
25/06/2014 - 7616371-001-04
5
1 Introduction
1.1 Symbols used
1.1.1. Symbols used in the manual
In these instructions, various danger levels are employed to draw the
user’s attention to particular information. In so doing, we wish to
safeguard the user’s safety, highlight hazards and guarantee correct
operation of the appliance.
DANGER
Risk of a dangerous situation causing serious physical
injury.
WARNING
Risk of a dangerous situation causing slight physical
injury.
CAUTION
Risk of material damage.
Signals important information.
¼Signals a referral to other instructions or other pages in the
instructions.
1.1.2. Symbols used on the equipment
4
Protective earthing
~
Alternating current
Before installing and commissioning the device, read
carefully the instruction manuals provided.
Dispose of the used products in an appropriate recovery
and recycling structure.
Caution: danger, live parts.
Disconnect the mains power prior to any operations.
1 2
M002628-A
1. Introduction
AWHP-2 MIT-IN-2 iSystem
6
25/06/2014 - 7616371-001-04
1.2 Abbreviations
4 DHW: Domestic hot water
4 PPS: Polypropylene hardly inflammable
4 PCU: Primary Control Unit - PCB contoller for heat pump operation
4 PSU: Parameter Storage Unit - Parameter storage for PCBs
PCU and SU
4 SCU: Secondary Control Unit - DIEMATIC iSystem control panel
PCB
4 SU: Safety Unit - Safety PCB
4 3WV: 3-way valve
4 EVU: Power supply company
4 AWHP: Outdoor module connected by connection cable to the
indoor module
4 MIT-2: Indoor module fitted with a DIEMATIC iSystem control
panel
4 HP: Heat pump
4 EER: Frigorific efficiency ratio
4 COP: Performance coefficient
4 EER: Frigorific efficiency ratio
1.3 Liabilities
1.3.1. Manufacturer’s liability
Our products are manufactured in compliance with the requirements
of the various applicable European Directives. They are therefore
delivered with [ marking and all relevant documentation.
In the interest of customers, we are continuously endeavouring to
make improvements in product quality. All the specifications stated in
this document are therefore subject to change without notice.
Our liability as the manufacturer may not be invoked in the following
cases:
4 Failure to abide by the instructions on using the appliance.
4 Faulty or insufficient maintenance of the appliance.
4 Failure to abide by the instructions on installing the appliance.
1.3.2. Installer’s liability
The installer is responsible for the installation and commissioning of
the appliance. The installer must respect the following instructions:
4 Read and follow the instructions given in the manuals provided
with the appliance.
AWHP-2 MIT-IN-2 iSystem
1. Introduction
25/06/2014 - 7616371-001-04
7
4 Carry out installation in compliance with the prevailing legislation
and standards.
4 Perform the initial start up and carry out any checks necessary.
4 Explain the installation to the user.
4 If a maintenance is necessary, warn the user of the obligation to
check the appliance and maintain it in good working order.
4 Give all the instruction manuals to the user.
1.4 Homologations
1.4.1. Certifications
This product complies to the requirements to the european directives
and following standards:
4 2006/95/EC Low Voltage Directive. Reference Standards:
EN60335-1 / EN60335-2-40.
4 2004/108/EC Electromagnetic Compatibility Directive. Generic
standards: EN1000-6-3 , EN 61000-6-1.
1. Introduction AWHP-2 MIT-IN-2 iSystem
8
25/06/2014 - 7616371-001-04
2 Safety instructions and
recommendations
2.1 Safety instructions
DANGER
If smoke is released or in case of refrigerant leak:
1. Do not use a naked flame, do not smoke, do not
operate electrical contacts or switches ( doorbell,
light, motor, lift, etc..).
Contact between refrigerant and a flame may result
in emissions of toxic gases.
2. Open the windows.
3. Trace possible leaks and seal them immediately.
WARNING
Before any work, switch off the mains supply to the
appliance.
WARNING
Do not touch the refrigeration connection pipes with your
bare hands while the appliance is running. Danger of
burns or frost injury.
2.2 Recommendations
WARNING
4 Any intervention on the appliance and heating
equipment must be carried out by a qualified
engineer.
4 For a proper operating of the boiler, follow carefully
the instructions.
AWHP-2 MIT-IN-2 iSystem 2. Safety instructions and recommendations
25/06/2014 - 7616371-001-04
9
Keep this document close to the place where the boiler is
installed.
CAUTION
4 Use tools and pipe components especially designed
for use with R410A refrigerant.
4 Install the appliance on a solid, stable structure able
to bear its weight.
4 Use phosphorous-deoxidised copper for pipes
without welds and copper alloy to connect the pipes
carrying the refrigerant.
4 Use only R410A gas to fill the pipes with refrigerant.
4 Do not install the appliance in a place where it may
be exposed to steam, sulphuric gas or combustion,
an atmosphere with a high salt content, or which may
be covered by snow.
4 Ensure correct earthing.
4 Store the refrigeration connection pipes away from
dust and humidity (danger of damage to the
compressor) and cover both ends until the expansion
process is complete.
4 Do not use a load cylinder.
CAUTION
4 Activate the main switch at least 12 hours before the
appliance starts to function. Using the appliance just
after it is switched on may seriously damage the
internal parts.
4 When switching off the appliance, wait for at least 5
minutes of post-operation before deactivating the
main switch. Danger of breakdown or water leak.
CAUTION
In order to limit the risk of being scalded, the installation of
a thermostatic mixing valve on the domestic hot water flow
piping is compulsory.
Before carrying out any maintenance work requiring the
shutdown of the inside module, also cut the power supply
to the outside module to prevent any errors in
communication.
2. Safety instructions and recommendations AWHP-2 MIT-IN-2 iSystem
10
25/06/2014 - 7616371-001-04
3 Technical description
3.1 General description
The AWHP-2 MIT-IN-2 iSystem heat pump is composed of two
elements:
4 The outside unit handles energy production in hot or cold mode.
4 The inside module handles thermal exchange between the R410A
fluid and the hydraulic circuit.
The two units are connected by means of refrigeration and electrical
connections.
The system offers the following advantages:
4 The heating circuit is housed in the insulated volume within the
home. There is no danger of the pipes freezing.
4 Thanks to the DC inverter system, the heat pump modulates its
output to adapt to the needs of the home.
4 The control panel uses the outside temperature sensor to adjust
the temperature of the heating circuit according to the outside
temperature.
3.2 Main parts (Indoor module)
3.2.1. MIT-IN-2/H
1
Automatic air bleed
2
tank
3
High energy efficient heating pump
4
Plate heat exchanger
5
electrical support
6
Flowmeter
7
Table cover unit
8
Control panel
9
Safety valve
10
Pressure gauge
11
Expansion vessel
M002483-A
2
3
5
4
8
7
6
11
10
9
1
AWHP-2 MIT-IN-2 iSystem 3. Technical description
25/06/2014 - 7616371-001-04
11
3.2.2. MIT-IN-2/E
1
Automatic air bleed
2
tank
3
High energy efficient heating pump
4
Plate heat exchanger
5
electrical support
6
Flowmeter
7
Table cover unit
8
Control panel
9
Safety valve
10
Pressure gauge
11
Expansion vessel
12
Automatic air bleed
13
Electric heater
3.3 Operating principle
3.3.1. General
The outside module produces heat or cold (in reversible versions) and
transmits it to the heating circuit via the refrigerant in the plate
exchanger.
The outside module is capable of operating at outside temperatures
down to -20°C (-15°C in the case of a 4 kW or 6 kW heat pump).
The DIEMATIC iSystem control panel is used to programme and
regulate the heat pump according to the outside temperature.
By activating the pumps and, where necessary, the mixer valve, the
regulator handles the regulation of the heating.
Connection of a CDR4 simplified remote control or a CDI4 interactive
remote control enables the auto-adaptivity of the gradient and the
parallel offset of the heating curve.
The antifreeze function on the installation is active whatever the
operating mode. It is triggered as soon as the outdoor temperature
reaches the limiting value preset to +3°C.
The installation of a buffer tank is not necessary if the volume of water
in the circuit is higher than or equal to 3 litres/kW: Therefore, for a
heat pump with an output of less than 11 kW, with a water volume of
less than 33 litres, the installation of a buffer tank is necessary.
M002484-A
13
2
3
5
4
8
7
6
11
10
9
1
12
3. Technical description
AWHP-2 MIT-IN-2 iSystem
12
25/06/2014 - 7616371-001-04
3.3.2. Skeleton Diagrams
n
MIT-IN-2/H
1
Inside module with hydraulic back-up
2
tank
3
Filter
4
Flowmeter
5
Radiator
6
Plate heat exchanger
7
Outdoor unit
8
Boiler
n
MIT-IN-2/E
1
Inside module with electrical back-up
2
tank
3
Electrical back-up
M002487-E
2
1
3
4
5
8
7
6
M002488-E
2
1
3
4
5 8
6
7
AWHP-2 MIT-IN-2 iSystem 3. Technical description
25/06/2014 - 7616371-001-04
13
4
Radiator
5
Plate heat exchanger
6
Filter
7
Flowmeter
8
Outdoor unit
3.3.3. Pressure available
A
Pressure available (mbar)
Z
Water flow rate (m3/h)
1 - 5
Setting the pump
¼To set the speed of the heating pump correctly, refer to
chapter: "Setting the speed of the heating pump on the inside
module", page 94.
3.4 Technical specifications
3.4.1. Electricity supply
230 V AC (+/- 10%) - 50 Hz
400 V AC (+ 6%, - 10%) - 50 Hz (depending on the model)
M002627-C
0
100
200
300
400
500
600
700
800
0 0,5 1 1,5 2 2,5 3
1
2
4
3
2
1
5
3. Technical description
AWHP-2 MIT-IN-2 iSystem
14
25/06/2014 - 7616371-001-04
3.4.2. Heat pump
Conditions of use:
4 Limit operating temperatures in Hot mode:
- Water: +18 °C / +60 °C
- Outside air:
-15 °C / +35 °C (4, 6 kW)
-20 °C / +35 °C (8, 11, 16, 22, 27 kW)
4 Limit operating temperatures in Cooling mode:
- Water: +7 °C / +25 °C
- Outside air: +15 °C / +40 °C (At less than 18°C, it is necessary
to use the HK24 insulation kit option)
4 Maximum operating pressure: 3 bar
n
Performances in hot mode with outside air temperature
at +7°C and outlet water temperature at +35°C (in
accordance with EN 14511–2)
AWHP
4 MR 6 MR -2 8 MR-2 11 MR-2 11 TR-2 16 MR-2 16 TR-2 22 TR 27 TR
Calorific output - A7/W35 kW 3.72 5.87 8.26 10.56 10.56 14.19 14.19 19.4 24.4
COP hot - A7/W35
4.30 4.18 4.27 4.30 4.30 4.22 4.22 3.94 3.90
Absorbed electrical power - A7/W35 kWe 0.87 1.41 1.93 2.46 2.46 3.36 3.36 4.92 6.25
Nominal amperage - A7/W35 A 4.11 6.57 8.99 11.81 11.81 16.17 16.17 7.75 9.86
n
Performances in hot mode with outside air temperature
at +2°C and outlet water temperature at +35°C (in
accordance with EN 14511–2)
AWHP
4 MR 6 MR -2 8 MR-2 11 MR-2 11 TR-2 16 MR-2 16 TR-2 22 TR 27 TR
Calorific output - A2/W35 kW 3.76 3.87 5.93 10.19 10.19 11.38 11.38 12.10 14.70
COP hot - A2/W35
3.32 3.26 3.20 3.20 3.20 3.27 3.27 3.10 3.10
Absorbed electrical power - A2/W35 kWe 1.13 1.19 1.85 3.19 3.19 3.48 3.48 3.91 4.70
Nominal amperage - A2/W35 A 6.1 6.1 8.2 10.7 6.2 14.6 8.4 9.7 11.8
n
Performances in cold mode with outside air
temperature at +35°C and outlet water temperature at
+18°C (in accordance with EN 14511–2)
AWHP
4 MR 6 MR -2 8 MR-2 11 MR-2 11 TR-2 16 MR-2 16 TR-2 22 TR 27 TR
Cooling output kW 3.84 4.69 7.90 11.16 11.16 14.46 14.46 17.65 22.2
EER
3.80 3.80 3.99 4.68 4.68 4.43 4.43 3.8 3.8
Absorbed electrical power kWe 0.72 1.15 2.0 2.35 2.35 3.65 3.65 4.65 5.84
AWHP-2 MIT-IN-2 iSystem 3. Technical description
25/06/2014 - 7616371-001-04
15
n
General values
AWHP 4 MR 6 MR -2 8 MR-2 11 MR-2 11 TR-2 16 MR-2 16 TR-2 22 TR 27 TR
Sound pressure
(1)
dB(A) 41.7 41.7 43.2 43.4 43.4 47.4 47.4 51.8 53
Nominal water flow
(ΔT = 5K)
m3/h
1.04 1.04 1.47 1.88 1.88 2.67 2.67 3.8 4.6
Manometric height
available at nominal
flow rate
mbar 618 618 493 393 393 213 213 - -
Nominal air flow rate
m3/h
2100 2100 3000 6000 6000 6000 6000 8400 8400
Power voltage of the
outdoor unit
V 230 V~ 230 V~ 230 V~ 230 V~ 400 V3~ 230 V~ 400 V3~ 400 V3~ 400 V3~
Sound output
(2)
dB(A) 63.7 63.7 65.2 65.4 65.4 69.4 69.4 73.8 75
R410A refrigerant kg 2.1 2.1 3.2 4.6 4.6 4.6 4.6 7.1 7.7
refrigerant piping
connection (LiquidGas)
inch 1/4-1/2 1/4-1/2 3/8-5/8 3/8-5/8 3/8-5/8 3/8-5/8 3/8-5/8 3/8-3/4 or
3/8-1
1/2-3/4 or
1/2-1
Max pre-loaded
length
m 10 10 10 10 10 10 10 30 30
Weight (empty) Outside unit
kg 42 42 75 118 118 130 130 135 141
(1) 5 m from the appliance, free field.
(2) Test conducted in accordance with the standard NF EN 12102
3.4.3. Sensor characteristics
Outside sensor
Temperature in °C -20 -16 -12 -8 -4 0 4 8 12 16 20 24
Resistance in Ω 2392 2088 1811 1562 1342 1149 984 842 720 616 528 454
DHW sensor
Flow sensor
Temperature in °C 0 10 20 25 30 40 50 60 70 80 90
Resistance in Ω 32014 19691 12474 10000 8080 5372 3661 2535 1794 1290 941
3. Technical description AWHP-2 MIT-IN-2 iSystem
16
25/06/2014 - 7616371-001-04
4 Installation
4.1 Regulations governing installation
CAUTION
Installation of the appliance must be done by a qualified
engineer in accordance with prevailing local and national
regulations.
4.2 Package list
4.2.1. Standard delivery
The delivery includes:
4 An outside module (See below)
4 An inside hydraulic module (See below)
4 An outside sensor
4 Refrigerant adapter fitting 4, 6 and 22 kW
4 A mounting rail (screwed to the pallet)
4 The installation and maintenance instructions
4 The user instructions
Combinations possible:
Models
Outdoor unit Indoor module
Description Pack no. Description Pack no.
HPI 4 MR-2
AWHP 4 MR EH336
MIT-IN-2/H 4 - 8 ISYS
MIT-IN-2/E 4 - 8 ISYS
EH386
EH389
HPI 6 MR-2
AWHP 6 MR-2 EH380
MIT-IN-2/H 4 - 8 ISYS
MIT-IN-2/E 4 - 8 ISYS
EH386
EH389
HPI 8 MR-2
AWHP 8 MR-2 EH381
MIT-IN-2/H 4 - 8 ISYS
MIT-IN-2/E 4 - 8 ISYS
EH386
EH389
HPI 11 MR-2
AWHP 11 MR-2 EH382
MIT-IN-2/H 11 - 16 ISYS
MIT-IN-2/E 11 - 16 ISYS
EH387
EH390
HPI 11 TR-2
AWHP 11 TR-2 EH383
MIT-IN-2/H 11 - 16 ISYS
MIT-IN-2/E 11 - 16 ISYS
EH387
EH390
HPI 16 MR-2
AWHP 16 MR-2 EH384
MIT-IN-2/H 11 - 16 ISYS
MIT-IN-2/E 11 - 16 ISYS
EH387
EH390
HPI 16 TR-2
AWHP 16 TR-2 EH385
MIT-IN-2/H 11 - 16 ISYS
MIT-IN-2/E 11 - 16 ISYS
EH387
EH390
HPI 22 TR-2
AWHP 22 TR EH225
MIT-IN-2/H 22 - 27 ISYS
MIT-IN-2/E 22 - 27 ISYS
EH388
EH391
HPI 27 TR-2
AWHP 27 TR EH226
MIT-IN-2/H 22 - 27 ISYS
MIT-IN-2/E 22 - 27 ISYS
EH388
EH391
AWHP-2 MIT-IN-2 iSystem 4. Installation
25/06/2014 - 7616371-001-04
17
4.2.2. Accessories
Various options are available depending on the configuration of the
installation:
n
Heat pump options
Description package
160 L storage tank EH 60
80 L storage tank EH 85
Wall-hanging kit for outside units 6 - 10 kW EH 95
Condensate receiver tank for wall bracket EH 111
Ground mounting supports for outside units EH 112
Electrical resistor for the condensate receiver tank EH 113
Frigorific ducts with insulation (5/8" - 3/8"); Length: 5 m EH 114
Frigorific ducts with insulation (5/8" - 3/8"); Length: 10 m EH 115
Frigorific ducts with insulation (5/8" - 3/8"); Length: 20 m EH 116
Insulated copper pipe (1/2" - 1/4") 10 m EH 142
1/4" 1/2" - 3/8" 5/8" adapter fittings EH 146
Heat pump hydraulic connection kit - DHW storage tank EH 149
Wall-hanging kit for outside units 11 - 27 kW EH 250
3-way valve module with standard pump EA 63
3-way valve module with electronic pump EA 67
Collector for 2/3 circuits EA140
Wall console EA141
Wall console for hydraulic module EA142
Direct circuit with pump HEE EA143
V3V circuit with HEE pump EA144
Wiring kit for connecting a safety thermostat for underfloor
heating
HA 249
3-way valve kit HK 21
2-circuit kit HK 22
Reversal valve kit HK 23
Insulation kit cold mode HK 24
3-way valve insulation kit HK 25
n
Control system options
Description
package
BUS connection cable (length 12 m) AD134
voice remote monitoring module AD152
Outlet sensor V3V AD199
DHW sensor AD212
Optional PCB for 3-way valve AD249
System sensor AD250
Outside radio-controlled temperature sensor AD251
Radio module AD252
CDR iSystem radio remote control AD284
4. Installation AWHP-2 MIT-IN-2 iSystem
18
25/06/2014 - 7616371-001-04
Description package
Interactive radio remote control with LCD display CD12/CD14 AD285
Radio remote control AD253
Interactive remote control AD254
A simplified remote control with room sensor FM52
Condensation detector kit HK 27
Energy metering option HK 29
4.3 Type plate
4.3.1. Outdoor unit
The type plate must be accessible at all times. The type plate
identifies the product and provides the following information:
4 Appliance type
4 Manufacturing date (Year - Week)
4 Serial number.
4 Nature of the power supply voltages
4.3.2. Indoor module
1
This data plate is affixed to the inside side panel of the
appliance in the factory.
2
When installation has been completed, affix the data plate
provided in the instructions bag to the casing of the
appliance in a position where it can be seen.
The type plate must be accessible at all times. The type plate
identifies the product and provides the following information:
4 Appliance type
4 Manufacturing date (Year - Week)
4 Serial number.
4 Nature of the power supply voltages
MW-M001832-2
M002624-A
Auf ERDGAS H eingestellt
für DE: Erdgas E
Réglé au gaz naturel H
Geregeld voor aardgas H
Preset for natural gas H
G20 - 20 mbar
8366-4038
1 2
AWHP-2 MIT-IN-2 iSystem
4. Installation
25/06/2014 - 7616371-001-04
19
4.4 Installing the outdoor module
4.4.1. Positioning of the appliance
Ensure that the outside module is optimally positioned in relation to
neighbours as it is a source of noise.
CAUTION
4 There must be no obstacles hindering the free
circulation of air around the outdoor module (intake
and output).
4 No not locate the outside unit close to where people
sleep.
4 Do not locate the unit opposite a wall with windows.
4 Avoid placing it close to a terrace, etc..
Choose a location away from prevailing winds.
C000373-B
Brrrrr....
Brrrrr....
Brrrrr....
Brrrrr....
In some cases, additional precautions are necessary owing to the
fact, for example, of too short a distance between you and your
neighbours.
When installing a noise reduction screen, respect the following
recommendations:
4 Locate the noise reduction screen as close as possible to the noise
source whilst allowing for the free circulation of air in the
exchanger on the outside unit and maintenance work.
Place the outside unit on a base (concrete base frame, sill,
concrete blocks, etc.) with no rigid connection with the building
served in order to prevent any transmission of vibrations. Ensure
sufficient above ground elevation (100 to 150 mm) to keep it above
water.
For regions where heavy snowfalls occur, raise this above ground
protection by at least 200 mm compared with the average depth of
the covering of snow.
M001448-A
4. Installation
AWHP-2 MIT-IN-2 iSystem
20
25/06/2014 - 7616371-001-04
CAUTION
4 If the outside temperatures become negative, take
the necessary precautions to prevent the risk of
freezing in the evacuation pipes.
4 Prevent any risk of the condensates freezing in an
area through which they flow.
4 The heating cord keeps the condensates from
freezing: See EH113 leaflet.
n
Distances to be observed
WARNING
To ensure that the heat pump functions correctly, respect
the minimum and maximum connection lengths between
the heat pump and the indoor module.
A
Outdoor unit
Z
Indoor module
A
Minimum length 5 m
Maximum length:
40 m for 4, 6, 8 kW,
75 m for 11, 16 kW,
20 m for 22, 27 kW.
B
Max height difference 10 m For 4, 6, 8 kW
Max height difference 30 m For 11, 16, 22, 27 kW
C
Max number of elbows: 15
Respect the minimum curve radii of 100 to 150 mm
¼See chapter: "Installing the pipes", page 30.
M00 1439-A
A
B
2
1
C
MW-M001450-2
G
F
F
G
A
C
B
B
C
E
A
1000
D
M
ax. 500
M
ax. 500
AWHP-2 MIT-IN-2 iSystem 4. Installation
25/06/2014 - 7616371-001-04
21
Dimension (mm) 4, 6, 8 kW 11, 16, 22, 27 kW
A
100 150
B
500 1000
C
200 300
D
1000 1500
E
300 500
F
150 250
G
100 200
4.4.2. Main dimensions
n
AWHP 4 and 6 MR-2
A
1/4" flare refrigerant fitting
Z
1/2" flare refrigerant gas fitting
150 500
800
887
300
183
155
365
600
40
10
23
69
18
90
MW-M002199-2
1
2
4. Installation AWHP-2 MIT-IN-2 iSystem
22
25/06/2014 - 7616371-001-04
n
AWHP 8 MR-2
A
3/8" flare refrigerant fitting
Z
5/8" flare refrigerant gas fitting
943
950
45
56
53 28
19
23
417
175
330
370
30
443
447
175
65 42
2
(1)
(2)
MW-M001442-2
1
AWHP-2 MIT-IN-2 iSystem 4. Installation
25/06/2014 - 7616371-001-04
23
n
AWHP 11 and 16 MR/TR-2
A
3/8" flare refrigerant fitting
Z
5/8" flare refrigerant gas fitting
1350
950
45
56
53 28
19
23
417
175 600
330
370
30
443
447
175
65 42
2
(1)
(2)
1
MW-M001443-2
4. Installation AWHP-2 MIT-IN-2 iSystem
24
25/06/2014 - 7616371-001-04
n
AWHP 22 and 27 TR
A
450 mm : 22 kW
424 mm : 27 kW
A
3/8" flare refrigerant fitting (22 kW)
1/2" flare refrigerant fitting (27 kW)
Z
3/4" flare refrigerant gas fitting + adapter 1" (to be
brazed)
MW-M002629-1
1338
1050
40
56
26
342
A
225
330
370
417
30
600
225
19
28
60
42
(1)
(2)
2
1
AWHP-2 MIT-IN-2 iSystem 4. Installation
25/06/2014 - 7616371-001-04
25
4.4.3. Locating the outside module
CAUTION
Keep the appliance vertical during transport.
n
Installation on the ground
1
Concrete base frame
2
Condensates run-off
3
Install a run-off channel with pebble bed
4 Use the ground installation base kit available as optional
equipment: Package EH112.
4 Install the appliance on a solid, stable structure able to bear its
weight.
n
Condensates discharge
CAUTION
If the outside temperatures become negative, take the
necessary precautions to prevent the risk of freezing in the
evacuation pipes. Use package EH113 (Electrical resistor
for the condensate receiver tank).
Prevent any risk of the condensates freezing in an area
through which they flow.
>45°
M001456-A
200
1
2
3
M001452-A
4. Installation AWHP-2 MIT-IN-2 iSystem
26
25/06/2014 - 7616371-001-04
4.5 Installing the indoor module
4.5.1. Positioning of the appliance
CAUTION
4 Install the appliance in frost-free premises.
4 Fix the appliance to a solid wall capable of bearing
the weight of the appliance when full of water and fully
equipped.
4.5.2. Main dimensions
A
3-way valve circuit return (Option) - G1"
Z
3-way valve circuit outlet (Option) - G1"
E
Return direct circuit - G1"
R
Direct circuit flow - G1"
T
Back-up boiler inlet - G1"
Only for hydraulic back-up - Version H
Y
Return to the back-up boiler - G1"
Only for hydraulic back-up - Version H
U
Gas line
5/8" flare connection: 4, 6, 8, 11, 16 kW
3/4" flare connection: 22, 27 kW (Use 1" braze-on
adapter)
I
Liquid line
3/8" flare connection: 4, 6, 8, 11, 16 kW
1/2" flare connection: 22, 27 kW
G
Exterior cylindrical threading, sealed by sheet gasket
T001898-C
600
min.1000
500
min.
250
min.
250
900
M002497-B
122
192
262
332
402
472
542
49 48
900
600
498
1234567
8
AWHP-2 MIT-IN-2 iSystem 4. Installation
25/06/2014 - 7616371-001-04
27
4.5.3. Assembly of the indoor module
n
Fitting the mounting rail
1. Drill 2 holes with a Ø of 10 mm.
Additional holes are provided in case one or other of the
standard locating holes prevents the correct location of the
plugs.
2. Put the plugs in place.
3. Fix the mounting rail to the wall using the hexagonal head screws
provided for this purpose. Set the level using a spirit level.
n
Fixing to the wall
CAUTION
Weight (empty): 74 kg
Shipping weight: 112 kg
1. Present the indoor module above the mounting rail until it rests
firmly against it.
2. Gently lower the indoor module.
1
2
3
3
M002380-B
458
61
11
558
Ø10
M002381-C
4. Installation AWHP-2 MIT-IN-2 iSystem
28
25/06/2014 - 7616371-001-04
Loading...