Page 1
Quick Start Guide
10/100 PORTS 10/100 PORTS
1/2 3/4 5/6 7/8 9/10 11/12 13/14 15/16
10/100 PORTS 10/100 PORTS
1/2 3/4 5/6 7/8 9/10 11/12 13/14 15/16
The following Quick Start Guide will help you through a very brief version of the
initial installation, conguration and basic operation of the Closed IPTV Layer 3
Enhanced CCTV Switch.
Use this document in conjunction with the Installation & Operation Guide. This is
located on the Product CD supplied with the unit and can also be found on the
Dedicated Micros website (dedicatedmicros.com).
Check the contents of the box
Remove the packaging and check all items listed below are present.
• Layer 3 Enhanced CCTV Switch
• Power Supply
• Software/Documentation CD
• Quick Start Guide
If any of these items are missing; please contact the Dedicated Micros Customer
Service team on +44 (0) 845 600 9501
Upgrading to Closed IPTV
There are some NVR’s that are Closed IPTV enabled, but require a software
upgrade to ‘discover’ the Layer 3 Enhanced CCTV Switch and allow the system to
operate fully as Closed IPTV. Navigate to System->Attributes page on the connected
NVR and select the Software button. Check the Software Revision number, in the
format of 6.6 (8.0017) M3UP 2010-10-31 14:50. NVR units at 6.6 (8.XXXX) or above
do NOT require an Upgrade. Closed IPTV may be disabled (below).
Installing The Unit
Step 1 - Set the switch Hardware identier
There is a rotary switch on the base of the Layer 3 Enhanced CCTV Switch used by
the NVR to identify the unit.
The Ecosense NVR has a built in Layer 3 enhanced CCTV switch set to identity ‘0’,
the SD Advanced does not.
● The rst e
‘1’, the n
● The rst external switch attached to an SD Advanced should be set to
‘0’, the next one set to ‘1’ etc.
Step 2 - Connecting the Layer 3 Enhanced CCTV Switch to a
compatible Dedicated Micros NVR
xternal switch attached to an Ecosense NVR should be set to
ext one set to ‘2’ etc.
NOTE: The 48vDC power socket will only be available on the Power Over Ethernet
(POE) supporting model (DM/NSW/CPP)
Step 4 - Connecting the Unit to the General/Corporate Network
ETH-B is provided for connection to the General/Corporate network for viewing
and conguration.
ETH-D ETH-C ETH-B ETH-A
Use a CAT5 ethernet cable to connect ETH-B on the Layer 3 Enhanced CCTV
Switch. The NVR is DHCP capable by default and can obtain an IP address from
the General/Corporate network (if a DHCP server is present). Otherwise a static
IP address can be set on the NVR Network->Network conguration page.
Step 5 - Connecting a Camera to the Unit
If the Software Revision number BELOW 6.6 (8.XXXX), the unit requires upgrading.
1) Insert the supplied Upgrade CD into the NVR CD/DVD drive.
2) Reset the NVR. The NVR will boot into an upgrade state. Follow the
onscreen instructions to initiate the upgrade.
Note: The Upgrade can take up to 40 minutes to complete, during which time the
NVR will NOT be recording.
NOTE: Do NOT switch the NVR off if the upgrading message is on screen. Please
call Technical Support if there are any problems.
3) The system will reboot after the Upgrade has been applied. Use the
NVR conguration pages to navigate to System-> Attributes and select
enable from the Closed IPTV drop down.
4) Click Save.
Conguring Closed IPTV
The Closed IPTV logo in the top left corner of the conguration pages gives a quick
indication of whether the system is in Secure or Conguration mode. Dedicated
Micros recommend the system is always left in Secure Mode unless Closed IPTV
settings are actually being edited.
Secure Mode Conguration Mode
Connect the Layer 3 Enhanced CCTV Switch to the NET socket on the back of the
Dedicated Micros NVR (being used for control/conguration purposes) via a CAT5
Ethernet cable. The Ethernet port labelled ‘ETH-A’ is designated the ‘Closed IPTV
control’ port. The Closed IPTV control port is intended to securely link the Layer 3
Enhanced CCTV Switch to the Dedicated Micros NVR.
Step 3 - Connecting Power to the Unit
The connected NVR will automatically discover the switch once power is applied.
DM/NSW/CP
Use the supplied 12vDC power cable to connect the 12vDC power socket on the
rear of the unit to a local power source.
DM/NSW/CPP (POE Version)
Use the supplied 48vDC power cable to connect the 48vDC power socket on the
rear of the unit to a local power source.
Connect the video sources to the Layer 3 Enhanced CCTV Switch. Connect each
video source using an RJ45 link cable. Individual cameras should be connected
in sequential order, i.e. connect the rst camera to port number 1 on the Layer 3
Enhanced CCTV Switch. When this connection is registered by the NVR, it will
display a notication on the Main Monitor showing the recognised details of the new
video source, including resolution, name and MAC address.
Note: If an IP camera is connected to a channel occupied by an existing BNC
connection, it will be recognised but not assigned as the BNC connection
will take priority. It will instead be added to an unassigned list of cameras,
which can be tied to a channel in the conguration pages. If a BNC camera
is connected to a channel occupied by an existing IP connection, the BNC
connection will take priority. The IP connection will be dropped and added
to an unassigned list of cameras, which can be tied to a channel in the
conguration pages.
Key
Port Free
Unknown
SATA1
SERIAL 2
SERIAL 1
SERIAL 3 PTZ
HDMI 1
OUT
OUT
IN
IN
AUDIO
AUDIO
NET
NET
USB
MON A
EXP
KBD
SERIAL 4 PTZ
A
B
MON
IR
ALARMS
VID 17 VID 18 VID 19 VID 29VID 24VID 22VID 20 VID 21 VID 23 VID 25 VID 26 VID 28 VID 27 VID 30 VID 31 VID 32
VID 1
VID 2 VID 3
RELAYS
Layer3 Enhanced
SD Advanced
I
O
VID 13VID 8VID 6VID 4 VID 5 VID 7 VID 9 VID 10 VID 12VID 11 VID 14 VID 15 VID 16
CCTV Switch
Analogue Connection
Single IP connected
Single IP assigned
Multiple IP connection
Duplicate channel alloc
Page 2
Quick Start Guide
Conguring the Unit
Access the NVR conguration pages and navigate to Closed IP -> Settings.
Settings
Conguration mode
The security settings of all cascaded Layer 3 Enhanced CCTV
Switches and the conguration of video sources connected to the
Layer 3 Enhanced CCTV Switch can be edited.
Use this mode when conguring the Closed IPTV system only.
The switch is not secure in this mode. Cameras can be physically
swapped around and congured by the user as required.
Note: In Conguration mode, there is no registration of a camera fail. The
cameras are either in a not connected state or connected when present.
In Secure Mode, Closed IPTV security is enabled and the selected
security settings are applied.
IMPORTANT: The ‘Restrict public access (Eth B)’ setting (Closed IPTV-> Settings)
must be enabled if using Oracle IP domes in a Closed IPTV
environment.
Unit Security Settings
It is recommended that all security settings are enabled to prevent illicit access to
the system
Discover
This page shows the currently connected switches and allows forced discovery
of all Layer 3 Enhanced CCTV Switches connected to the NVR. The NVR (in
conguration mode) will automatically discover switches as they are connected.
Upgrade
This page provides the option to upgrade a selected switch (or all switches)
Once a switch is connected and Discovered, the connected NVR can upgrade it.
Select the switch to be upgraded and press the Upgrade button. The NVR sends the
required le to the Switch and restarts it.
Advanced
This page allows access to the advanced facilities on the NVR such as Autosync
and setting the base camera number of a switch.
The on-screen image of the Layer 3 Enhanced CCTV Switch provides instant
information regarding camera connection ports.
Port Illustration Colour Key
Port Free (Black) █ No video source currently connected to the port
Analog Connection (Blue) █ Analogue camera input using the BNC
Single IP Connected (Green) █ A single IP camera is connected directly to the
Single IP Assigned (Turquoise) █ A camera that has either ;
Multiple IP Connections (Yellow)
Duplicate Channel Allocation (Orange)
Unknown (White) A port which has detected a network connection
Security Level Select from Conguration Mode’ or ‘Secure Mode’. The NVR will
default to Conguration Mode, allowing the Closed IPTV system to
be set up. The system should only be put into Secure mode once all
conguration has been completed.
and nothing assigned to that channel.
connection for this channel on the back of the
NVR.
port and will be auto assigned to the channel.
been congured manually independently
outside Closed IP or
is one of the cameras assigned by Closed IP by
connecting a multi channel encoder.
█ A port that is hosting a multiple channel input
█ A port that has analogue and IP connection
applied to it. The IP source will be un-allocated.
but the type of connected device is not
recognised.
Click on the Discover button whilst in Conguration mode to nd all connected Layer
3 Enhanced CCTV Switches. Click on Accept to conrm the discovered settings and
add the switch and associated cameras to the Closed IPTV system
Click ‘Auto-Synchronise NVR variables with cameras’ when the unit is in
conguration mode to synchronise some of the settings (eg camera title) with
a newly added camera. This synchronisation will only occur for Remote Codec
cameras (ie NetVu Connected cameras and video servers) .
Switch
Each switch can have up to 16 video sources attached to it. A switch may not have
all ports congured with a video source, so there may be more than two switches
attached to the NVR. This option sets the base camera number on the selected
switch, all subsequent video sources on that switch will receive a consecutive
number. The ‘Cameras’ option will display the camera numbers that have been
assigned to the switch by the Closed IPTV NVR.
MI-Q-ENS/E1-2
Loading...