Decolav 5234 User Manual
LINEN TOWER INSTALLATION
INSTRUCTIONS
CARE AND CLEANING
• DO NOT clean the product with Detergents, Acid, Abrasives, Harsh Cleaners or a cloth with a coarse surface (S.O.S.® Pads, Scotch Brite® Pads).
This is good advice for any plumbing xture regardless of material.
DO NOT allow your DECOLAV
•
DO clean your DECOLAV
•
be used. Use a mild furniture polish to clean wood frame.
DO clean your DECOLAV
•
RECOMMENDED TOOLS
Tape Measure
®
product to unnecessarily encounter other solid objects.
®
product. Wipe with a damp cloth and dry with a soft cloth. If necessary, a general mild soap and water solution can
®
mirror. Wipe with a glass cleaner and a clean soft cloth. Use a mild furniture polish to clean wood frame.
Phillips
Screwdriver
Drill
Level
1
Pencil
Step #1
o Determine where the Linen Tower is to be placed
o Install the Anti Tip bracket on the back of the Linen Tower in the predrilled holes using the supplied
screws. Figure A
o Measure the distance from the oor to the top screw hole on the installed Anti Tip bracket on the Linen
Tower.
o Use this measurement to mark the wall for the second Anti Tip bracket.
o Install the second Anti Tip bracket on the wall at the same height as the one on the Linen Tower. Use
screws if stud is available, if no stud is available use drywall anchors (not included). Figure B
Back of
Linen Tower
Anti Tip
Bracket
Pre-drilled Hole
Anti Tip
Bracket
Figure A
NOTE: Due to vast di erence in building materials, wall anchors are not provided but are recomended throughout instructions.
Customer Service: 561-274-2110
www.decolav.com
Wall
LET YOUR DREAMS COME ALIVE, YOUR PASSIONS
BECOME REALITY, BE THE ENVY OF YOUR NEIGHBORS
Figure B
®
LINEN TOWER INSTALLATION
INSTRUCTIONS
Step # 2
o Slide the Linen Tower toward the wall. Leave enough room behind the wall cabinet to install the zip tie to
connect the two Anti Tip brackets. Figure C
o Connect the two Anti Tip brackets with the Zip tie and leave the Zip Tie a little loose. Figure C
o Slide the linen tower against the wall and level by adjusting the oor glides.
o Pull the Zip Tie tight and clip o the excess using scissors or cutting pliers
Zip Tie
Figure C
Notes:
o Pictured item may be di erent than actual item. This document is for instructional purposes only.
o We recommend two people to install this product.
Anti Tip
Bracket
2
Adjusting the Hinges
o The rear screw will move the door closer to the end panel or
away from the end panel. If the door is rubbing the end panel,
use this adjustment screw. Remember to adjust both hinges on
the door for the desired clearance. Figure D
o To get the doors even across the top and bottom edges of the
doors use the side to side adjustment screw. Remember to
adjust both hinges on the door for the correct position. Figure D
o Doors were adjusted at the factory prior to shipping but due to
the variances in home walls the hinges may need slight
adjustment.
Figure D
Hinge Plate Screws
Moving the Hinges to the Opposite Side
o Unclip the Hinge from the Hinge plate using the hinge
release button on the back of the hinge between the
hinge plate and the hinge. Figure E
o Repeat for all hinges on door and lay door to the side.
o Unscrew the two mounting screws on each Hinge Plate
and move the move them to the opposite side.
Figure E
o Repeat for all the hinge plates
Hinge Release
Button
Side to Side Adjustment
Front to Back Adjustment
Hinge Plate
Customer Service: 561-274-2110
www.decolav.com
Figure E
LET YOUR DREAMS COME ALIVE, YOUR PASSIONS
BECOME REALITY, BE THE ENVY OF YOUR NEIGHBORS
Hinge
®
Loading...