Decolav 5230 User Manual

ATTACHING UNITS

CAMERON MODULAR SERIES

1

5221 Vanity with
1661 Top

5225 Drawer Console
with 1664 Top

5222 Vanity with
1662 Top

5226 Vanity Drawer
with 1665 Top

5223 Vanity with
1663 Top

5230 Suppport Leg

Note: Tops are to be purchased separately, the are not included with base unit. Tops Shown on items for illustration purposes only

TABLE OF CONTENTS

Installation Instructions Page
o Product Con gurations 2

o Installing the Vanity 4
o Installing the Drawer Console with the Vanity and Support leg 5 & 6
o Installing the Vanity Drawer with the Vanity and the Support Leg 6 & 7
o Installing the Sink to the Vanity Top 8
o Installing the top to the Vanity 9
o Hinge Adjustment and Care and Cleaning 10
o Limited Lifetime Warranty 11

Customer Service: 561-274-2110
www.decolav.com

LET YOUR DREAMS COME ALIVE, YOUR PASSIONS

BECOME REALITY, BE THE ENVY OF YOUR NEIGHBORS

®

PRODUCT CONFIGURATIONS

CAMERON MODULAR SERIES

2

Note: Products shown above with optional accessories: Mirrors, Sinks, Vanity Tops and Vanity Stools avalible
separately

Customer Service: 561-274-2110
www.decolav.com

LET YOUR DREAMS COME ALIVE, YOUR PASSIONS

BECOME REALITY, BE THE ENVY OF YOUR NEIGHBORS

®

THANK YOU

CAMERON MODULAR SERIES

RUSTIC MODULAR SERIES

3

Dear Valued Customer,
DECOLAV
satis ed with your new product. We welcome and look forward to helping you create another unique look for your next
bathroom project.

Prior to installation, please take a moment to review all provided materials and hardware. For assistance with your new product,
please contact our dedicated DECOLAV

Sincerely,

Robert H. Mayer
Chief Executive O cer and President

®

would like to take this opportunity to thank you for your purchase – It is our sincere hope that you are completely

®

customer service sta .

CHANGING THE WAY YOU VIEW THE BATHROOM

BEFORE YOU BEGIN

®

1. Prior to installation, unpack your new DECOLAV® product and inspect it. Keep the product in its original package until you
are ready to install it.

2. The wall must be square, plumb and level.

3. Shut the water supply o when replacing an existing  xture. Preparation of the  oors and walls, including all additional wall
supports, may be required.

4.

Observe all local plumbing and building codes.

5. It is recommended that a professional contractor be retained for the installation of this product.

6. Anchors and wall screws are not provided.

RECOMMENDED TOOLS

Tape Measure

Adjustable Wrench

Pipe Clamp

Channel Locks

Drill

Hack saw

Level

Phillips
Screwdriver

Pencil

Pipe Wrench

Square

Plumber’s Putty
or Caulking

Ruler

Customer Service: 561-274-2110
www.decolav.com

Putty Knife

Flathead
Screwdriver

LET YOUR DREAMS COME ALIVE, YOUR PASSIONS

BECOME REALITY, BE THE ENVY OF YOUR NEIGHBORS

Scroll Saw

Pipe Cutter

®

CAMERON MODULAR SERIES

Hookup Hardware Included with the Vanity Drawer and the Drawer Console

4

Item Desription QTY

A

BC

A Connecting Bolt (Included with Drawer Console and Vanity Drawer) 4
B Flat Washer (Included with Drawer Console and Vanity Drawer) 4
C Connecting Wood Screw (Included with Drawer console and Vanity

6

Drawer
D T-nut (Included with Drawer Console and Vanity Drawer) 4
E Small T nut screw (included with Drawer console and Vanity Drawer) 12

DEF

F Insert Nut, Factory installed on Support Leg 2

Note: Hookup Hardware is Only Provided with the Vanity Drawer and the Drawer Console. No Hookup
Hardware is Provided with the Vanities.

INSTALLING THE VANITY

STEP #1

o If a Vanity drawer or a Drawer console is to be hooked to the vanity skip to the hook up sections on

Page 5 and 6. Follow hook up steps. Once Vanity hookup is complete follow Vanity installation

instructions.
o Carefully remove vanity from carton and place safely aside.
o Turn o water supply to faucet.
o Remove existing vanity.
o Determine the location on the wall where the vanity will be installed.
o Measure the vanity width and height and mark outline on wall.

STEP #2

o Measure and mark the locations of the plumbing pipes and lines
o Make a cutout in the back panel of the vanity using a circular saw or saber saw, allow enough room for
the plumbing lines and pipes to pass through.
o Drill 2, 3/16” diameter holes in the vanity back rail. These holes will be used to connect the vanity to the
wall using wall anchors or screws (not included).
o Carefully Position the vanity in the desired location.
o Level the vanity side to side and front to back using a carpenter’s level and adjust the leg levelers. The leg
levelers are located at the bottom of each leg.
o Attach vanity to wall using wall anchors or screws (not included).

Customer to bore holes in
the back rail for attching the
vanity to the wall.

Figure B

Notes:
o We recommend two people to install this vanity

Customer Service: 561-274-2110
www.decolav.com

Customer to make cutout
in vanity back panel

LET YOUR DREAMS COME ALIVE, YOUR PASSIONS

BECOME REALITY, BE THE ENVY OF YOUR NEIGHBORS

Figure A

®