Decolav 1720 User Manual
BENNETT BATH VANITY
1.4”
36
17.5”
445
13”
330
3.5”
89
3.5”
89
1.4”
35
21.6”
548
20"
508
5"
127
Finished Wall
item #1720-GAW / 1720-RAW / 1720-WEG
USE AND CARE GUIDE
THANK YOU FOR CHOOSING DECOLAV
We appreciate the trust and condence you have placed in DECOLAV® through the purchase of our products. We strive to continually create and manufacture quality
products designed to enhance your home. Visit us online at decolav.com for our full line of products, and follow us on Facebook, Twitter and Pinterest for the most
up-to-date information, product care tips and trends.
PRE-INSTALLATION
NOTE: Actual wood color, grain pattern and other appearance
characteristics may vary within each veneer species and grade.
NOTE: It is recommended that a professional contractor be
retained for the installation of this product.
• Unpack your new DECOLAV product and inspect it for damage. Keep the product in its original package until you are ready to install it
• The oor and walls must be square and level
• Shut the water supply o when replacing an existing xture
• Preparation of the oors and walls, including all additional wall supports, may be required
• Observe all local plumbing and building codes
RECOMMENDED TOOLS
tape measure phillips screwdriver drill level pencil
CARE AND CLEANING
• Do clean your DECOLAV product to maintain its new appearance over the years. Wipe with a damp cloth and dry with a soft cloth. If necessary, a general mild soap and
water solution can be used. Use only a mild furniture polish to clean wood frame
• Do not clean the product with detergents, acids, abrasives, harsh cleaners or cloths with a coarse surface (S.O.S.® pads, Scotch Brite® pads, etc.)
• Do not allow your DECOLAV product to unnecessarily encounter other solid objects
item #1720-GAW / 1720-RAW / 1720-WEG
Part Quantity
Vanity body
Front towel bar
(polished)
Decorative extension
(polished and brushed)
Machine screw 2
Lock washer 2
1
1
2 each
Flat washer 2
Glass wall 12
PRODUCT DIMENSIONS AND PARTS LIST
45"
1143
42”
1067
38.9”
987
127
21.6”
548
20"
508
5"
Vanity dimensions:
42” W x 21.6” D x 36” H
with decorative extension:
45” W x 21.6” D x 36” H
© DECO LAV, INC. 2014
915
36”
32”
813
front view side view
25.5”
648
5"
127
PLEASE CONTACT 18663326528 FOR FURTHER ASSISTANCE
DECOLAV.COM
1
Lock Washer
Flat Washer
Machine Screw
Front Towel Bar
Apply Silicone Here
Lavatory
(Sold separately)
Machine Washer
Lock Washer
Flat Washer
Decorative Extension
(Included)
Decorative Extension
(Included)
Apply Silicone Here
Lavatory
(Sold separately)
Apply Silicone Here
Machine Washer
Side Mounted Towel Bar
(Sold separately)
Drilled Hole
10mm
Decorative Extension
Hole
Position Template
Drill
Machine Washer
Lock Washer
Lock Washer
Flat Washer
Flat Washer
Lavatory
(Sold separately)
Side Mounted Towel Ba
(Sold separately)
Decorative Extension
(Included)
Decorative Extension
(Included)
Apply Silicone Here
Lavatory
(Not Provided
Purchased Separately)
D
E
F
C
I
Drawer
Apply Silicone Here
Side Mounted Towel Bar
(Not Provided
Purchased Separately)
Lavatory
(Not Provided
Purchased Separately)
D
E
F
Side Mounted Towel Bar
(Not Provided
Purchased Separately)
I
Drawer
BENNETT BATH VANITY
Machine Screw
Lock Washer
Flat Washer
item #1720-GAW / 1720-RAW / 1720-WEG
ASSEMBLY INSTRUCTIONS
Use Decolav drain item #9290-CP/SN/PN/DB,
NOTE:
9296-CP/SN/PN/DB or #9298-CP/SN/PN/DB.
Decolav cannot guarantee leakage wih other manufacturer drains.
1
SETTING UP YOUR NEW VANITY
• Carefully remove your new vanity from carton and place safely aside
• Turn o water supply to faucet
• Remove existing vanity
• Determine the location in the bathroom the vanity will be installed
• Measure the vanity width and height and mark outline on wall
• Move the vanity into place and level with the adjustable glides on bottom feet
• Locate and mark wall studs
2
CHANGING THE FRONT MOUNTED TOWEL BAR
lease note both a polished and brushed towel bar are included for your
(P
convenience)
• Slide the drawer out until fully extended. See gure 1
• While holding the Front Mounted Towel Bar, loosen the Machine Screw inside
both drawers
• Carefully remove and set aside the Machine Screws, Flat Washers and Lock
Washers. You will use them again
• Align the Front Mounted Towel Bar with the holes inside the vanity bottom
shelf. Insert the Machine Screw, Flat Washer and Lock Washer through the
hole inside the vanity bottom shelf. Re-tighten the Machine Screw on the
Front Mounted Towel Bar
• Repeat step to secure the opposite side of the Front Mounted Towel Bar
3
INSTALLING DECORATIVE EXTENSION
NOTE: Use Decolav decorative bottle trap item #9102-CP/SN/
PN/DB to complete the look.
Figure 1
Figure 2
Drilled Hole
10mm
• Measure and mark the location of the Decorative Extension by using the
cut-out template supplied. See gure 2
Carefully drill two holes, using a 3/
•
8” drill bit, through the vanity
cabinet wood. (Before drilling use commercial painters tape to help
prevent wood and finish from splitting)
4
INSTALLING SIDE MOUNTED TOWEL BAR
• Side Mounted Towel Bar is sold separately
• Measure and mark the location of the Side Mounted Towel Bar by using the
cut-out template supplied. See gure 3
Carefully drill two holes, using a 3
•
5
INSTALLING QUARTZ COUNTERTOP WITH INTEGRATED
/8” drill bit, through the vanity cabinet wood
LAVATORY
• Quartz countertop with Integrated Lavatory is sold separately
• Place the Quartz Countertop with Integrated Lavatory on top of the vanity cabinet. Adjustments
may be necessary to align correctly. See gures 5 and 6
• Insert the Glass Walls into the slots in the drawers. See gure 6
© DECO LAV, INC. 2014
Figure 5
Figure 3
Figure 4
Decorative Extension
Position Template
Drill
Drilled Hole
Hole
10mm
Drill
Side Towel Bar Hole
Position Template
Figure 6
PLEASE CONTACT 18663326528 FOR FURTHER ASSISTANCE
DECOLAV.COM
2
Loading...