Kit Contents:
• 10 - Aluminum balusters
(2.5 balusters required per linear foot of railing)
Items You Will Need:
CLASSIC BALUSTER
INSTALLATION INSTRUCTIONS
• Deckorators baluster
connectors (sold separately)
• Deckorators stair connectors
set at 35° (sold separately)
• Deckorators rail connectors
(optional, sold separately)
• Drill driver
• Tape measure
• Clamps
• Safety glasses
• Carpenter’s pencil
• White rubber mallet
• Support blocks (can be cut
from scrap rail material)
Installation Instructions:
INLINE RAILING
Prior to construction, check with your local regulatory agency for
special code requirements in your area. Common railing height is
36". Structural support should come from either the continuation
of deck support posts that extend up through the deck floor or
from railing posts that are bolted to the inside of the rim or outer
joist. 6' on-center post spacing is recommended. Never span
more than 8' on-center between railing posts.
Step 3: Using a drill driver, screw on Deckorators baluster
connectors (sold separately) on each mark using the screws
provided. Apply silicone caulk on each connector to prevent
balusters from turning or rattling after installation is complete.
The caulk should be on the outside of the connector, where the
baluster will make contact with the connector’s outer edge.
Note: Specific types of treated lumber are known to corrode
aluminum. Deckorators baluster connectors provide a barrier
between the aluminum balusters and treated lumber to ensure
long term performance.
Step 1: Measure railing opening, from post to post to
determine the length of each baluster rail section.
Step 2: Cut top and bottom rails (2x4s) to length and clamp
together. Mark top and bottom rails 4-1/2" on-center, starting from
the cetner of the rail.
Step 4: Place the bottom rail between the rail posts, supported
by a 3” block (2x4 scrap material works best). Secure rail to posts
using Deckorators rail connectors (sold separately) and slide
balusters over the bottom connectors. Carefully place top rail over
the balusters, making sure each baluster is seated properly on
each connector.
Step 5: Inspect nished railing for proper baluster spacing and
secure top rail. Add a cap rail for a nished look.
Step 8: Clamp the top and bottom rails together with the top 2x4
rail inverted. Position rails as shown and mark 5-1/2” on-center,
working from the center out to the ends of the rails.
STAIR RAILING
Step 6: For rail sections longer than 4’, support blocks are
recommended. These can be made from leftover 2x4 rail material.
Properly position the support block and toe-nail it to the bottom rail
and deck board.
Step 7: Stair rails and balusters can present an installation
challenge. Deckorators angled stair rail connectors (sold
separately) create a snug and accurate baluster t for stair angles
at 35 degrees. Cut top and bottom stair rails at the proper angle.
Lay top and bottom 2x4 rails alongside the posts and mark.
Step 9: Properly position the connectors on the rails. The top
and bottom connectors will be facing opposite directions. Screw
the connectors in place. To properly set angled connectors, begin
screwing vertically until the screw bites into the wood. Reposition
screw to the proper angle and tighten. Do not over-tighten, which
can move the connector off center.
Step 10: Make sure connectors are properly aligned, apply
silicone caulk to each stair connector, and assemble the top
and bottom rails with the balusters. Then attach full rail section
between the stair rail posts.
THE DIAGRAMS AND INSTRUCTIONS IN THIS BROCHURE ARE FOR ILLUSTRATION PURPOSES ONLY AND ARE NOT MEANT TO REPLACE A LICENSED PROFESSIONAL. ANY CONSTRUCTION OR USE OF THE
PRODU CT MUST BE IN ACCORDANCE WITH ALL LO CAL ZONING A ND/OR B UILDING CODES. T HE CONSUMER ASSUMES AL L RISK S AND LIABILIT Y ASSOCI ATED WI TH THE CONSTRUC TION OR USE OF THIS
PRODU CT. THE CONSUMER OR CO NTR ACTOR SHOU LD TAKE ALL NECESSARY S TEPS T O ENSURE THE SAFETY OF E VERYONE INVOLVED I N THE PR OJEC T, INCLU DING , BUT NOT LIMI TED TO, W EARING THE
APPROPRI ATE SA FETY EQUIPMEN T. EXCE PT AS CONTAI NED IN THE WRI TTEN LIMI TED WARRA NTY, THE WARRAN TOR DOES NOT PR OVID E ANY OTHER WARRA NTY, EITHER EXPRESS OR IMPLIED, AND SHALL
NOT BE LIABLE FOR ANY DAM AGES, INCLUDING CONS EQUEN TIA L DAM AGES .
©2018 Universal Forest Products, Inc. Deckorators is a registered trademark of Universal Consumer Products, Inc. in the U.S. All rights reserved.
68956 U.S. Highway 131, White Pigeon, MI 49099
10382_12/18
Deckorators.com
Loading...