DECKED DT2 User Manual
Installation Instructions:
DT2
TOYOTA TUNDRA
6’7” BED LENGTH
2007CURRENT
TOOLS REQUIRED
• Adjustable wrench (that opens to about 1”)
• 1/2” open end wrench
• #2 Phillip screwdriver
• 3/8” socket
Watch short installation videos at www.decked.com/video | Register your system at www.decked.com/warranty
FOLLOW US:
VERSION 4
DECKED.COM | 208.806.0251
• 7/16” deep socket
• 7/32” Allen wrench
• 1/2” drill bit
• Wire cutters
• T40 Torx Driver
@DECKEDUSA | #DECKEDUSA
CONTENTS
DECKED carton
LEFT/DRIVER deck half - 1
RIGHT/PASSENGER deck half - 1
Center vert - 1
Drawer - 2
Cabside ammo can - 2
Tailgate side ammo can - 2
Ammo can lid - 4
Ammo can window - 2
C-channel - 2
Ruler - 1
Hardware box - 1
Hardware box - unbagged components
(inside DECKED carton):
Shims - Toyota 55/65 - 4
Weather strips - 2
Handle - 1
Bottle opener - 1
▼ ASSEMBLY OVERVIEW ▼
HARDWARE box - bagged components
PREP SD/TUN - 1
CCHANNEL HW 1
BOLT 1 FS - 1
CS AMMO CANS - 1
J3 - 2
J5 - 2
DRAWER 1 1
DRAWER 3 1
HANDLE 1
WHEELS 1
FINAL FS 1
PREPEXTRA 1
LEFT/DRIVER
DECK HALF
AMMO CAN
WINDOW
COVER
JHOOK
ATTACHMENTS
RIGHT/PASSENGER
DECK HALF
AMMO
CAN LID
CABSIDE AMMO
CAN
RULER
CCHANNEL
TAILGATE
AMMO CAN
CENTER VERT DRAWER
Page 2 | v.4 | DT2 DECKED. COM | #DECKEDUSA | @DECKEDUSA
▼ HEY! TORQUE BOY: READ BEFORE YOU INSTALL DECKED ▼
1. DON’T be an idiot read the instructions.
2. DON'T over tighten bolts, get em' hand-tight.
3. DON'T use power tools.
4. If you don't follow directions and do use power tools:
1). Set clutch at a very low setting. 2). If you blow it, see NOTE.*
NOTE* Two extra threaded inserts are included in BAG PREP-EXTRA. That’s all you get. The inserts will replace any
stripped inserts in the tailgate ammo cans, but NOT THE CENTER VERT, so hand tighten until snug only! You can
also screw the inserts back in if dislocated. There is a straight screwdriver slot on the underside of the insert.
TAILGATE ammo cans have wide bottoms; CABSIDE ammo cans have narrow bottoms.
NOTE: You will need a buddy to help with exactly two steps, not including draining the sixpack or snapping
pics of you posing.
5. DON'T over tighten J-hooks during installation.
Make 'em good and snug enough to keep the
system from moving in the bed.
6. Nice job if you’re still reading .
Prevent abusive, expletitive-filled language, watch our detailed installation video
or give us a call. We’re happy to help!
208.806.0251 | DECKED.COM/INSTALLVIDEO
AMMO CAN DRAIN HOLES
(TO DRILL OR NOT TO DRILL.)
• Do you use a tonneau or shell over your DECKED system?
There is no need to drill holes.
• Does your DECKED system live outside?
The ammo cans will get water in them. You’ll need to drill holes in the ammo cans.
There are two dimples in the bottom of each ammo can. Drill a 1/2” hole at each dimple. A smaller hole
will get clogged.
DECKED. COM | #DECKEDUSA | @DECKEDUSA DT2 | v.4 | Page 3
SHIMS
• There are 4 SHIMS provided:
• Using the information in the respective circular detail views:
a) Clean the surfaces thoroughly where the shims will be located (isopropyl alcohol is recommended).
b) Remove the layer of tape on the bottom of the shim to expose the adhesive surface.
c) Place the shim and apply with pressure.
NOTE: Repeat details A and B on passenger side.
DETAIL A
Place shim 5 1/2” from tailgate side of floor. Center
shim between floor beads shown. Repeat opposite side.
DETAIL B
Place shim 3” from cabside panel. Center shim
between floor beads shown. Repeat opposite side.
5 1/2”
3”
CABSIDE
B
A
TAILGATE
Page 4 | v.4 | DT2 DECKED. COM | #DECKEDUSA | @DECKEDUSA
PREP BED
(JUST LIKE YOUR MOMMA TAUGHT YOU.)
• Remove all factory tie-downs on both sides of truck bed (T40 Torx driver required).
Make sure to SAVE THE FACTORY TUNDRA BOLTS, as you will need them for the DECKED brackets.
• Install DECKED tie-down brackets on both sides of truck using bolts from step above; BAG PREP SD/TUN.
SAVE THESE BOLTS REUSE BOLTS
PREP SD/TUN
FACTORY TUNDRA
TIEDOWN BRACKETS
DECKED. COM | #DECKEDUSA | @DECKEDUSA DT2 | v.4 | Page 5
TIEDOWN BRACKETS
DECKED
Loading...