Installation Instructions:
DN3
NISSAN TITAN
5’7” BED LENGTH
2016CURRENT
TOOLS REQUIRED
• Adjustable wrench (that opens to about 1”)
• 1/2” open end wrench
• #2 Phillip screwdriver
• 3/8” socket
Watch short installation videos at www.decked.com/video | Register your system at www.decked.com/warranty
FOLLOW US:
VERSION 5
DECKED.COM | 208.806.0251
• 7/16” deep socket
• 7/32” Allen wrench
• 1/8” Allen wrench
• 1/2” drill bit
• Wire cutters
@DECKEDUSA | #DECKEDUSA
CONTENTS
DECKED carton
LEFT/DRIVER deck half - 1
RIGHT/PASSENGER deck half - 1
Center vert - 1
Drawer - 2
Cabside ammo can - 2
Tailgate side ammo can - 2
Ammo can lid - 4
Ammo can window - 2
C-channel - 2
Ruler - 1
Hardware box - 1
Bottle opener - 1
Torsion brace - 1
Hardware box - unbagged components
(inside DECKED carton):
Shims NISSAN - DN3/DN4 - 4
Weather strips - 2
Handle - 1
▼ ASSEMBLY OVERVIEW ▼
HARDWARE box - bagged components
PREP TBO - 1
BOLT 1 FS(B1) - 1
CCHANNEL 1
CS AMMO CANS - 1
J5 - 4
DRAWER 1 1
DRAWER 3 1
HANDLE 1
WHEELS 1
WASHERS 1
PREPEXTRA 1
AMMO
CAN LID
LEFT/DRIVER
DECK HALF
AMMO CAN
WINDOW
COVER
RIGHT/PASSENGER
DECK HALF
RULER
CABSIDE AMMO
CAN
CCHANNEL
TAILGATE
AMMO CAN
CENTER VERT
BOTTLE OPENER
Page 2 | v.5 | DN3 DECKED. COM | #DECKEDUSA | @DECKEDUSA
TORSION BRACE
DRAWER
▼ HEY! TORQUE BOY: READ BEFORE YOU INSTALL DECKED ▼
1. DON’T be an idiot read the instructions.
2. DON'T over tighten bolts, get em' hand-tight.
3. DON'T use power tools.
4. If you don't follow directions and do use power tools:
1). Set clutch at a very low setting. 2). If you blow it, see NOTE.*
NOTE* Two extra threaded inserts are included in BAG PREP-EXTRA. That’s all you get. The inserts will replace any
stripped inserts in the tailgate ammo cans, but NOT THE CENTER VERT, so hand tighten until snug only! You can
also screw the inserts back in if dislocated. There is a straight screwdriver slot on the underside of the insert.
TAILGATE ammo cans have wide bottoms; CABSIDE ammo cans have narrow bottoms.
NOTE: You will need a buddy to help with exactly two steps, not including draining the sixpack or snapping
pics of you posing.
5. Start all bolts with fingers to avoid cross-threading
6. DON'T over tighten J-hooks during installation.
Make 'em good and snug enough to keep the
system from moving in the bed.
7. Nice job if you’re still reading .
Prevent abusive, expletitive-filled language, watch our detailed installation video
or give us a call. We’re happy to help!
208.806.0251 | DECKED.COM/INSTALLVIDEO
AMMO CAN DRAIN HOLES
(TO DRILL OR NOT TO DRILL.)
• Do you use a tonneau or shell over your DECKED system?
There is no need to drill holes.
• Does your DECKED system live outside?
The ammo cans will get water in them. You’ll need to drill holes in the ammo cans.
There are two dimples in the bottom of each ammo can. Drill a 1/2” hole at each dimple. A smaller hole
will get clogged.
DECKED. COM | #DECKEDUSA | @DECKEDUSA DN3 | v.5 | Page 3
SHIMS
• There are 4 DOUBLE STACKED shims provided:
• Using the information in the respective circular detail views:
a) Clean the surfaces thoroughly where the shims will be located (isopropyl alcohol is recommended).
b) Remove the layer of tape on the bottom of the shim to expose the adhesive surface.
c) Place the shim and apply with pressure.
NOTE: Repeat details A and B on passenger side.
DETAIL B
Place shim 1 1/2” from seam in floor (blue). Align tailgate side
of shim 4” from rear of floor. Repeat on passenger side.
1 1/2”
4”
DETAIL A
Align shim to seam in floor (blue). Place shim
2” from cabside panel of bed. Repeat on passenger side.
2”
CABSIDE
A
B
TAILGATE
Page 4 | v.5 | DN3 DECKED. COM | #DECKEDUSA | @DECKEDUSA