Page 1
6FT Climbing Dome with Slide
SAFETY GUIDELINES
At the beginning of each play season
• Tighten all hardware. Lubricate all metallic moving parts per manufacturer’s instructions.
• Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose,
cracked, or missing.
• Check metal parts for rust. If found, sand and repaint using a nonlead-based paint meeting the
requirements of 16 CFR 1303.
• Reinstall any plastic parts, such as any other items that were removed for the cold reason.
• Rake and check depth of loose fill protective surfacing materials to prevent compaction and to
maintain appropriate depth. Replace as necessary.
Twice a month during play season
• Tighten all hardware.
• Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose,
cracked, or missing.
• Rake and check depth of loose fill protective surfacing materials to prevent compaction and to
maintain appropriate depth. Replace as necessary.
SAFETY GUIDELINES
• This product in intended for indoor, outdoor, domestic use only.
• This product has not been designed for commercial use in play centers, nurseries etc.
• Place the equipment on level ground, not less than 6ft from any structure or obstruction such
as fence, garage, house, overhanging branches, laundry lines, or electrical wires.
• Do not install home playground equipment over concrete, asphalt, packed earth, grass,
carpet, or any other hard surface. A fall onto a hard surface can result in serious injury or
death to the equipment user.
• To prevent serious injury, children must not use the equipment until properly installed.
• Risk of using helmets and other items that can wrap around child’s neck, become entangled
or entrapped by the equipment, and lead to strangulation or death.
•
The maximum fall height for the product is around 3ft.
•
This product is designed to be used by no more than 3 children at the same time between
the ages of 3 to 8.
• Maximum user weight for slide is 100 pounds.
• On-site adult supervision for children of all ages is required at all times. Never leave children
unattended.
• Do NOT allow children to use the equipment in a manner other than intended.
• Do NOT allow children to wear inappropriate items, such as but not limited to, loose fitting
clothing, hood and neck drawstrings, scarves, cord-connected items, capes and ponchos.
These items can cause death by strangulation.
• Do NOT allow children to climb when the equipment is wet.
• Do NOT attach items to the playground equipment that are not specifically designed for use
with the equipment, such as, but not limited to, jump ropes, clothesline, pet leashes, cables
and chain as they may cause a strangulation hazard.
• Dress children with well fitting and full foot enclosing footwear. Examples of inappropriate
footwear are clogs, flip flops, and sandals.
• Do NOT allow loose, hooded or baggy clothes to be worn as children can get trapped and
may be unable to free themselves. Children should not wear cycle helmets whilst on this
equipment.
Once a month during play season
• Lubricate all metallic moving parts per manufacturer’s instructions
At the end of each play season or when the temperature drops below 32°F
• Remove other items as specified by the manufacturer and takes indoor or do not use.
• Owners shall be responsible for maintaining the legibility of warning labels.
Disposal Instructions
When you wish to disassemble or dispose of the product please completely disassemble the unit
and discard of it in a safe place and manner so as not to present any hazard to any individual.
PLEASE DO NOT RETURN TO STORE
STOP
Please do not return this product to the retailer!!
We are able to assist you in ANY way
If you find that you have any trouble with assembly or
missing or damaged parts please contact the seller.
Page 2
DOME PARTS LIST
DOME PARTS LIST
(32 ¾")
F1 M8×38mm Bolt
(x 19pcs)
F3 M6×59mm Bolt
(x 12pcs)
S1 M8 Flat Nut
(x 19pcs)
T1 M8 Washer
(x 27pcs)
F4 M6×
Bolt
(x 4pcs)
S2 M8 Hooded Nut
(x 4pcs)
T2 M6 Washer
(x 36pcs)
51mm
F2 M8×35mm Bolt
(x4pcs)
F5 M6×32mm Bolt
(x 2pcs)
S3 M6 Hooded Nut
(x 18pcs)
1#Tube (Green) x 4pcs
2#Tube (Blue) x 18pcs
3#Tube (Green) x 17pcs
4#Tube (Green) x 2pcs
5#Tube (Green) x 1pc
6#Tube (Green) x 1pc
7#Tube (Green) x 1pc
8#Tube (Green) x 2pcs
(24 ⅞")
(23 ⅗")
(23 ⅗")
(
Note:
(23 ⅗")
(21 ⅝")
(42 ⅓")
Tube#5 & 6 are exactly the same)
(47 ¼")
9# Plastic Borad
(x3pcs)
11# Large Climbing Rock
(x 11pcs)
10# Small Climbing Rock
(x8pcs)
Spanner (x 1pc)
12# Slide
(x1pcs)
Allen Key
(x 1pc)
Page 3
STEP 1
STEP 2
Lay out 4pcs tube#1, 3pcs tube#3 and 1pc tube#5 in sequence as shown
below, connect them with bolts and washers to form a circle.
Do not use Flat Nut to secure the bolt at this step.
NOTE:
The screws go through from inside out, with the head of the bolt on the
inside. The convex side of the tube always faces inward of the dome.
1#Tube (x 4pcs)
3#Tube (x 3pcs)
5#Tube (x 1pcs)
3
1
F1 M8×38mm Bolt
(x 8pcs)
1
T1 M8 Washer
(x 8pcs)
Attach 2pcs tube#3 to both ends of tube#1, and 2pcs tube#2 to both
ends of tube#3(at the bottom) to form upside-down V shapes with
bolt and washer.
Repeat the same to make a total of 7 V shapes.
Secure the bottom 8 joints with M8 Flat Nut. Make sure the nuts are
just tight enough to hold the pieces in place, but not fully tightened.
It will help increase flexibility in following assembly.
3#Tube (x 8pcs)
2#Tube (x 6pcs)
external
3
T1+F1
3
internal
S1 M8 Flat Nut
1
3
(x 8pcs)
3
2
F1 M8×38mm Bolt
(x 7pcs)
T1 M8 Washer
(x 7pcs)
1
3
3
1
1
3
external
1
3
T1+F1
internal
Bottom Joint
3
S1
5
internal
1
5
3
1
2
3
5
1
3
2
3
Page 4
STEP 3 STEP 4
Connect the 7 V-shape (triangles) together with 6pcs tubes#2, use 7pcs
M8 Flat Nut to secure the tubes in place.
*Do not fully tighten the flat nut at this step.
2#Tube (x 6pcs)
1
3
2
S1 M8 Flat Nut
(x 7pcs)
3
2
2
1
3
2
Add 4pcs tube#3 and 6pcs tubes#2 in the order illustrated below to form
the middle level.
Connect the tubes at the top with bolt and washer as shown below.
*Remove the 7pcs M8 Flat Nut previously installed before adding tube#2
and tube#3.
2#Tube (x6pcs)
3
3#Tube (x4pc)
1
3
3
2
3
5
3
3
1
F1 M8×38mm Bolt
(x 4pcs)
3
T1 M8 Washer
(x 4pcs)
2
2
2
5
3
3
1
2
3
1
external
2
1
3
3
internal
1
3
external
3
3
internal
2
2
Page 5
STEP 5 STEP 6
Connect the top of the 6 triangle shapes formed in step 4 with 2pcs
tube#3 and 1pc tube#6, secure the joint with bolt and washer previously
attached, and 4pcs M8 Flat Nut.
*Do not fully tighten the flat nut at this step.
3
3#Tube (x2pcs)
6#Tube (x1pc)
2
internal
2
1
S1 M8 Flat Nut
(x 4pcs)
3
6
2
3
2
3
internal
1
Add 2pcs tubes#4 as illustrated, secure the upper end with bolt, washer
and nut previously attached, and the bottom end to tube#5 with 2pcs
M8x35 Bolts, M8 Washers, and M8 Hooded Nuts.
(upper end)
4#Tube (x2pcs)
Note: The end closer to the hole on the pole is the upper end.
T1 M8 Washer
(x 4pcs)
1
5
4
(lower end)
2
3
3
F2 M8×35mm Bolt
(x2pcs)
S2 M8 Hooded Nut
3
6
(x 2pcs)
1
3
3
2
3
3
5
6
2
1
1
3
1
4
3
3
1
3
Page 6
STEP 7 STEP 8
Place tubes#7 over 2pcs tube#4, secure both ends with M6x51mm Bolt,
M6 Washer and M6 Hooded Nut.
7#Tube (x1pc）
T2 M6 Washer
(x 4pcs)
5
F4 M6×51mm
Bolt (x 2pcs)
3
1
4
7
S3 M6 Hooded Nut
(x 2pcs)
1
3
1
Add 2pcs tube#8 between tube#6 and tube#7.
Secure them to tube#6 with M8x35 Bolt, M8 Washer, M8 Hooded Nut,
and to tube#7 with M6x51 Bolt, M6 Washer, and M6 Hooded Nut.
8#Tube (x2pcs）
5
F4 M6×51mm
Bolt (x 2pcs)
F2 M8×35mm Bolt
(x2pcs)
3
1
8
7
4
S3 M6 Hooded Nut
(x 2pcs)
S2 M8 Hooded Nut
(x 2pcs)
1
6
T2 M6 Washer
(x 4pcs)
T1 M8 Washer
(x 4pcs)
3
1
1
4
3
F4+T2
7
1
7
Note: Tube#8 should be
8
installed beneath tube#7.
3
F2+T1
3
6
8
S2
S3
Page 7
STEP 9 STEP 10
Add 3pcs Plastic Board over tube#8, and secure with M6x59mm Bolt, M6
Washer, and M6 Hooded Nut.
9# Plastic Borad
(x3pcs)
9
8
F3 M6×59mm Bolt
(x 12pcs)
1
T2 M6 Washer
(x 24pcs)
3
S3 M6 Hooded Nut
(x 12pcs)
1
Attach the Slide as illustrated, and secure it to tube#7 with M6x32mm Bolt,
M6 Washer and M6 Hooded Nut.
12#Slide (x1pc)
7
F5 M6×32mm Bolt
1
(x 2pcs)
T2 M6 Washer
(x 4pcs)
3
S3 M6 Hooded Nut
(x 2pcs)
1
3
7
5
9
8
6
12
5
4
1
7
9
1
3
12
7
1
3
1
3
Page 8
STEP 11 STEP 12
Install the climbing rocks to cover the bolt on each of the joint.
Add 8pcs Small Climbing Rocks to the bottom joints.
*Make sure all bolts and nuts are tightened as much as possible before
installing the climbing rocks, so that the rocks can be secured completely.
10# Small Climbing Rock
(x8pcs)
1
3
1
Install the Large Climbing Rocks on the joints not touching the ground.
Line up the notch on the bottom of the climbing rock with the tube on the
top of the joint.
*Make sure all bolts and nuts are tightened as much as possible before
installing the climbing rocks, so that the rocks can be secured completely.
Large Climbing Rock
11#
(x 11pcs)
3
1
1
3
5
1
1
3
5
1
1
3
*Make sure the tube fits
into the notch of the rock.
3
Loading...