De Agostini Sky Rider Drone User Manual
Pack 04
TM
www.model-space.com
CONTENTS
Another ve detailed, easy-to-follow stages
in building your Sky Rider Drone.
Stage 14: Straps for the battery case
Stage 15: Assembling the body
Stage 16: The first electronic speed control
Stage 17: Back left arm cover
Stage 18: Checklist
TM
www.model-space.com
Editorial and design by Continuo Creative, 39-41 North Road, London N7 9DP
All rights reserved © 2015
Published in the UK by De Agostini UK Ltd,
Battersea Studios 2, 82 Silverthorne Road, London SW8 3HE
Published in the USA by De Agostini Publishing USA Inc.,
915 Broadway, Suite 609, New York, NY 10010.
Items may vary from those shown.
Picture credits: p32 Corbis, p33-41 De Agostini, p42 Corbis
Responsibility
De Agostini advises that the use of Sky Rider Drone is subject to all the relevant regulations
currently in force. Such regulations require the prudent and responsible use of Sky Rider Drone
at all times, stating the responsibility of the user in the event that the same causes any damage
or injury to persons or property on the ground or to other users of the airspace in proximity of
which Sky Rider Drone ies. De Agostini also points out that it is not permitted to use Sky Rider
Drone for unauthorised or unlawful purposes; if Sky Rider Drone is used for unauthorised or
unlawful purposes, the user will be fully responsible for any loss or damage arising from such
unauthorised use. In particular, the user must comply with all provisions of law and refrain from
using Sky Rider Drone in any manner that could interfere with third-party privacy rights.
De Agostini declines any liability for any damage arising from the use of Sky Rider Drone.
Privacy rights
De Agostini recommends that the use of the built-in camera aboard Sky Rider Drone is in
accordance with the relevant provisions of law. The recording and disclosure of the image of a
person without their prior consent may in fact constitute infringement of law and involve the
responsibility of the author of such actions. De Agostini therefore recommends photographing
people only with their prior consent and not to use in any way these recordings (for example, by
storing and/or disseminating them by any means of communication) without rst obtaining such
consent. De Agostini recommends that images likely to harm the reputation or dignity of a person
are not disclosed. The use of Sky Rider Drone for purposes of monitoring or spying is strictly
prohibited and may be punishable by law.
Disclaimer
The explanations and specications set out in the relevant sections of Sky Rider Drone are
only for information purposes and are to be considered correct at the time of publication. They
have been prepared with the utmost attention in order to provide users with accurate and
reliable information. However, De Agostini cannot be held responsible for any consequences
arising from omissions and/or errors in these instructions, nor for any damage caused directly
or indirectly from the use of the information herein contained. Since the commitment of De
Agostini is designed to ensure continual updates and improvements, the product you have
purchased may slightly differ from the model described in the instructions.
IMPORTANT INFORMATION
Not suitable for children under the age of 14. This product is not a toy and is not designed or intended for use in play.
34
Assembly Guide
34
Straps for the battery case
Fixing the two straps for the battery case.
The second belt
As in the previous step, put the second belt into the
corresponding slots in the chassis. When complete, the
chassis should look like the photograph above.
The first belt
For this stage, you
will need the two
battery holder straps
from Stage 11, and
the chassis from this
stage, as seen in the
photo. Slide the first
belt into the slots as
shown. The strap is
fitted with the Velcro
side facing down.
21
Your parts
1. Chassis
2. 8 M3 nuts
3. Allen key 2.5mm
4. 3 screws M2 x 6mm
5. 3 screws M2 x 12mm
6. 2 screws M3 x 20mm
3
2
4 5 6
1
Stage 14
Assembly Guide
35
Assembling the body
Fixing the undercarriage and the chassis together.
You will need
For this stage’s assembly, you will need the
undercarriage bar (from Stage 4), the chassis (to
which you attached the straps in Stage 14), four
M3 x 12mm screws (from Stage 4) and four M3 nuts
(Stage 14). Arrange the pieces on your work table.
1
Your parts
1. Propeller 10 x 4.5 inches
CCW (counter-clockwise)
1
Stage 15
Loading...