Deadman Technologies AV01RF Users manual

AV01-RF Manual

Deadman Technologies, LLC Transceiver Module

AV01-RF, version 0.1

AV01-RF is a wireless transceiver data module with reasonably small form factor, low power
consumption, good stability and reliability. It has wide application uses in remote control,
industry automation, wireless telemetry and remote consumer applications. This module has an
embedded micro-controller and is highly versatile with several General Purpose Input and
Output (GPIO) options for equipment and other devices’ connectivity.

AV01-RF is designed with Texas Instruments CC2510F32 transceiver chip with embedded
MCU. The module comes preprogrammed from the factory employing spread spectrum
diversity and compliant to FCC 15.241

Changes or modifications not expressly approved by Deadman Technologies, LLC could
void the user's authority to operate the equipment.

FCC

The following statement must be placed in the finish product users manual:

Changes or modifications not expressly approved by Deadman Technologies, LLC could void the
user's authority to operate the equipment.

Or equivalently:

Changes or modifications not expressly approv ed by the party responsible for compliance could
void the user's authority to operate the equipment.

The following statement must be placed in the finish product users manual

“This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interfer ence in which
case the user will be required to correct the interference at his own expense.”

The following statement is required to be placed on the product. If the product is too small, (defined by <4
x 4 inches) or if approved by the FCC, this statement may be placed in the manual.

“This device complies with Part 15 of the FCC Rules. Operation is subject to the fo llowing two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.”

The finished product label must state the following:

Contains FCC ID: 244KR-AV01RF

Contains IC: 11230A-AV01RF
The FCC ID and/or IC certification numbers must be placed on a non-removable portion of the exterior of
the finished product. Contact Deadman Technologies, LLC for questions regarding placement of
certification numbers.

1

:

1

For class B devices (intended for residential use), contact Deadman Technologies for changes to required statements.

English

French

This device complies with Industry Canada licence-

Le présent appareil est conforme aux CNR d'Industrie

d'en compromettre le fonctionnement.

Industry Canada

The following statements (both English and French versions of the text) must be placed in the finish
product users manual:

exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not
cause interference, and (2) this device must accept any
interference, including interference that may cause
undesired operation of the device.

Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible

For laboratory use wherein FCC and IC approvals are not required:

The Texas Instruments CC2510 data sheet is appended in this users manual for detailed
instructions on programming, register settings and all other performance specifications related to
the GPIO, MCU programming and device performance. The IAR workbench is required to
adjust and reprogram the product. Any adjustment or reprogramming voids the users authority to
use the product outside the laboratory.

The device comes with one IO assigned from the factory. If additional IO assignments are
required, contact Deadman Technologies, LLC for firmware development of up to 21 GPIO with
custom defined interrupt routines.

The electrical specifications in the CC2510 data sheet are fully applicable to this module and
must be adhered to (see the CC2510 data sheet). Summary technical specifications are:

PERFORMANCE

Power Output:

Programmable up to 0dBm

RF Line-of-sight Range:

300m

RF Effective Rate:

Programmable up to 500kBaud

Receiver Sensitivity:

-103dBm@2.4kBaud

NETWORKING

Networking Topology:

Point-to-point, point-to-multipoint

POWER

Supply Voltage:

3.3 VDC external

Transmit Current:

26mA typical

Receive Current:

19.7mA typical

Sleep current:

0.220 mA typical

GENERAL

Communication Mode:

Half-duplex

2400Mhz – 2483.5Mhz; The module is

LLC.

Channel:

2 – default; multiple programmable BW/spacin g
dependent

Interface:

I^2S, UART, USB

PHYSICAL PROPERTIES

Size:

30mm×36mm×7mm

Weight:

20g

Antenna Base:

50Ω, chip antenna with balun

Operating Temperature:

Industrial:-40℃~+85℃

Frequency Stability:

±40ppm total tolerance including a) initial

dependence.

1. Summary Technical Specifications

programmed at the factory and certified wit h two
hopping frequencies of 2405MHz and 2425MHz

Frequency Band:

Any changes to the hopping frequencies
voids the FCC certification unless recerti fied
by the user or by Deadman Technologies,

tolerance, b) crystal
loading, c) aging, and d) temperature

2. AV01-RF Module Application Field

* AMR (Automatic Meter Reading)
* Wireless alarm and security systems
* Building automation, wireless monitoring, Access Control System;
* Wireless data transmission, automatic data collection system;
* Wireless remote control,
* Wireless LED display,
* Industry automation, wireless telemetry, SCADA
* Other ISM wireless data communication needs

3. How To Use The AV01-RF

TOP BOTTOM

1. Requires regulated 3.3VDC power supply