OPERATION MANUAL
Carpet Tile / LVT Flooring Cutter LP-650
www.dcutproducts.com
SAFETY RULES FOR THE FLOORING CUTTER
1. READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE
OPERATING THE D-Cut MULTI-FLOORING CUTTERS.
2. If you are not thoroughly familiar with the operation of D-Cut Multi-flooring
Cutter, obtain advice from a qualified instructor or call 630-916-9100 USA
3. Stay alert. Do not operate while under the influence of drugs, alcohol, or
medication.
4. Always wear safety approved eye protection with side shields(ANSI Z87.1)
5. Keep work area free of debris.
6. Keep children and unauthorized persons away from the D-Cut Multi-flooring
Cutter and work area.
7. Make sure tool is secure. Operate only on a firm substrate or solid stand.
8. Use the right tool. Do not force the D-Cut Multi-flooring Cutter or use it for a
job for which it was not designed; use only on approved materials.
9. Keep the blade sharp. A dull blade will not perform properly.
10. Always keep hands away from blade while operating or carrying the cutter.
11. Do not alter or misuse this tool. The D-Cut Multi-flooring Cutter is precision
built; modifications not specified in this manual may result in a dangerous
and unsafe environment.
12. Maintain the D-Cut Multi-flooring Cutter with care. Keep Blade sharp and
clean. Follow instructions for changing accessories.
13. Use only recommended accessories. The use of improper accessories may be
hazardous and cause injuries.
14. Never leave the D-Cut Multi-flooring Cutter unattended. Secure the handle
with the lock chain when not in use.
2
CUTTING AND C
Installation of the Cutter(1)
Install the wheel assembly to the cutter
base with provided nuts as shown.
Warning: Do not put your fingers
against the sharp edge of the blade at
any time.
Installation of the Cutter (2)
Install the handle assembly to the cutter
base with provided screws as shown.
Warning: Do not put your fingers
against the sharp edge of the blade at
any time.
Straight Cut
Insert the floor plank between the
cutting blade and the base, flush with
the guide bar on the working table and
hold the plank then pull handle down
to complete a cut.
Warning: Maintain control of the
handle. Do not allow handle to slam
back after making a cut.
3
Diagonal Cut
Position the guide bar at 45°. Insert a
carpet tile between the cutting blade
and the base, along with the guide bar
as shown, then pull the handle down to
complete a cut.
45° Cut
Position the guide bar at 45°. Insert
the floor plank between the cutting
blade and the base, along with the
guide bar as shown, then pull the
handle down to complete a cut.
Lengthwise Cut
Insert the floor plank between the
cutting blade and the working table
along with the guide bar which can
be locked on both sides of the
working table. Keep moving the
plank along with the guide bar after
each cut until the complete plank is
cut.
4
Notch Cut
Make a lengthwise cut first to the
desired length on the floor plank as
mentioned above, then turn the
plank 90°, and put desired cutting
point under the blade.
Unlock two screws on the blade
holder and pull out the blade as
shown to above mentioned desired
cutting point, then pull the handle
down to complete a cut.
Changing the Blade
First loosen the two screws on the blade
and remove the stopper screw holder
and pull out the blade as shown. Use
provided Allan wrench to remove the
nine screws, then carefully move the
blade out of the small blade holder.
Note: the flat side of the blade should
face the working table.
Warning: Do not put your fingers
against the sharp edge of the blade at
any time.
Transportation
Slide the lock pins to lock the cutting
head when the cutter is not use to keep
the blade in a close position for the
safety as shown on top illustration.
Pull out the carry handle while the lock
pins are released as shown on bottom
illustration.
5
Explosive View
6
Explosive View
1
Screw M10 × 40 2
2
Wheel 2
3
Lock Nut M10 6
4
Wheel Base 2
5
Rubber Foot B 2 41 Guide Bar 1
6
Screw M6 ×12 4 42 Rotating Shaft 1
7
Washer φ6 5 43 Washer φ16 2
8 Front Cutter Base
9
Screw M8 × 50 6 45 Screw M6 × 20 4
10
Spring Washer φ8 16 46 Screw M8 × 55 2
11
Washer φ8 14 47
12
Wheel Shaft 1 48
13
Nylon Bar 1 49 Handle B
14
Screw M5 × 20 7 50 Right ABS Handle 1
15
Screw M6 × 10 9 51 Nut M4 2
16
Blade 1 52 Screw M4 × 30 2
17
Pull Ring 1 53 Left ABS Handle 1
18
Spring Washer φ5 8 54 Latch 2
19
Screw M5 × 14 8 55 Screw M5 × 8 20
20 Sliding Nylon Piece A
21
Spring Washer φ6 1 57 Guide Bar Socket 10
22
Customized Screw M6 × 10 1 58 Screw M8 × 20 4
23
Screw M10 ×55 2 59 Carry Handle Assembly 1
24
Screw M8 × 10 8 60 Screw M8 × 12 4
25
Right Bracket 1 61 Rear Cutter Base 1
26
Left Side Cover 1 62 Right Side Cover 1
27
Knurling Screw M6 × 12 2 63 Sliding Base 2
28
Pin 4 64 Screw M6 × 45 4
29
Sliding Socket 2 65 Rubber Feet A 2
30
Right Cutter Base 1 66 Left Cutter Base 1
31 Sliding Nylon Piece A
32
Knurling Screw M6 × 45 2 68
33
Blade Holder Base 1 69 Screw M8 × 25 4
34
Short Guide Pillar 2 70 Left Bracket 1
35
Long Guide Pillar 2 71 Long Supporting Bar 2
36
Spring 4 72 Screw M6 × 20 4
Parts Q’ty Parts Q’ty
37
Blade Holder 1
38
Carry Handle Base 2
39
Spring Pin Assembly 1
40
Short Supporting Bar 1
1 44 Nylon Cam Ring 4
Handle A
Knurling Screw M8
2 56 Working Table 1
2 67 Screw M8 × 40 4
Flange Nut M10 12
1
1
1
7
Loading...