Dcs Outdoor WRT15I, WR15I Wrapper
WRAPPER FOR FREE STANDING ICEMAKER
INSTALLATION INSTRUCTIONS
Before you begin, read these instructions completely and carefully.
Getting Started
Remove packaging and retain until installation is complete.
CAUTION:
The surface on which the grill cart and Icemaker are located must be at and level. Icemaker should be
installed near water and drain supply. All plumbing must be out of the way of any foot trac.
Note: Wrapper must be installed on the Icemaker and attached to the grill cart before the grill head is
installed on the cart.
WARNING!
Some parts have sharp edges; care must be taken when handling the various components to avoid injury.
Please read safety information provided in these instructions before beginning assembly. Wear gloves
when handling.
Contents
Part Description Qty
Hardware Kit Includes:
Protective Grommet, 2.50 Diameter
Protective Grommet, 1.25 Diameter
Machine Screw 10-24 X 1-1/8
Sheet Metal Screw 10-24 X 1/2
Hex Bolt 1/4-20 X 1/2
Nut, Hex 1/4-20
Nut, Tinnerman U-nut #10-24 MS
Machine Screw 10-24 X 3/8
7” Cable Tie
Installation Instructions
Assembly instructions for Freestanding
application:
Tools Required
Phillips Screwdriver
1
1
1
8
2
2
2
4
4
1
5/16 Socket/Nutdriver and 5/16 Wrench
Safety Glasses
Work Gloves
Loosen (2) screws on front bottom grill cover 1.
(Fig. 01) approx. 1/8”. (No need to remove screws.)
Note: Installation of optional drain pump (sold
separately - model # RF15I-P) must be done
before installation of wrapper.
Front bottom grill cover
Screws
Fig. 01
1
Remove (4) screws on back panel of Icemaker as 2.
shown (Fig. 02). (Retain screws for re-use.)
Place the left side panel on the unit by sliding the 4.
bottom front ange behind the front grill plate
(Fig. 07). Then lift the rear of the panel so the U-nut
holes are visible in the slotted holes of the upper
and lower rear anges of the panel. Install machine
screws (10-24 X 3/8) into U-nuts as shown (Fig. 08
and 09). Do not tighten at this point.
Upper rear ange
Screws
Fig. 02
Install 2 Tinnerman U-Nuts on Icemaker Adapter 3.
(Fig. 03) and attach to upper area of Icemaker as
shown (Fig. 04). Repeat for the bottom location
(Fig. 05). Tighten all screws at this point. See
Fig. 06 for nal placement.
U-nut
Icemaker
adapter
Upper
screw
U-nut
near top
Female catch
U-nut
Lower rear ange
Repeat Step 4 for the other side panel. 5.
Place both top risers on top of unit as shown in 6.
Fig. 10.
Bottom front
ange
Fig. 07
Fig. 09
Screw
U-nut
Female catch
Fig. 08
Screw
Fig. 03
Fig. 05
Lower
screw
U-nut
near oor
Fig. 04
Icemaker
adapters
Fig. 06
Ensure
holes
are
aligned
Top risers
Side view
Fig. 10
Ensure
holes
are
aligned
2
Using screws provided (10-24 X 1-1/8), attach riser 7.
to the side panels. Take note of the alignment of the
holes on the riser and side panel (Fig. 11).
Ensure
holes
are
aligned
Fig. 11
Adjust the side panels to be level with the top of the 8.
Icemaker, then tighten all ange screws.
The 4 male catch clips are preinstalled in the back 9.
panel. See your Icemaker Use & Care Manual for
instructions on connecting to your potable water
supply and drain. Route the supply hose thru the
large opening in the back panel and connect to
the inlet on the back of the Icemaker. If you have
installed the optional drain pump (sold separately model # RF15I-P), feed the drain line thru this same
large opening. Feed the power cord thru the smaller
opening and install protective grommets on both
openings (Fig. 12).
Once you have tested the unit and veried there 10.
are no leaks, align the rear panel male clips to the
preinstalled female clips of the side panels, push at
the outer corners to engage clips. See Fig. 13 for
nal assembly. Do not bundle-up excess hose & cord
behind the panel.
Fig. 13
Solid Surface Installation – Required Accessory
(sold separately):
Solid Surface for Icemaker (WRT15I) ■
Locate holes on the solid surface and place onto 1.
the Icemaker so the holes align on the sides.
Check for proper t and alignment. Insert screws
(10-24 X 1-1/8) to anchor solid surface to risers. See
Fig. 14 for nal assembly.
Vent hose
Power cord
Water inlet
Drain hose
Fig. 12
Rear of Icemaker
shown with
optional drain
pump installed
Fig. 14
Final check to see that all spacing and gaps are even 2.
and level.
3
Loading...