Dcs Outdoor WR24RTD Wrapper
WRAPPER FOR FREE STANDING OUTDOOR BEER
DISPENSER, REFRIGERATOR & REFRIGERATED DRAWERS
INSTALLATION INSTRUCTIONS
Before you begin, read these instructions completely and carefully.
Getting Started
Remove packaging and retain until installation is complete.
CAUTION:
The surface on which the grill cart and refrigerated unit is located must be at and level.
Note: Wrapper must be installed on the refrigerated unit and attached to the grill cart before the grill
head is installed on the cart.
WARNING!
Some parts have sharp edges; care must be taken when handling the various components to
avoid injury. Please read safety information provided in these instructions before beginning
assembly. Wear gloves when handling.
Contents
Part Description Qty
Back Panel 1
Side Panels (right and left)
Top Riser
Male Strike Catch Clips (pre-attached)
Female Strike Catch Clips (pre-attached)
Hardware Kit Includes:
Protective Grommet
MS 10-24 X 1-1/8 PH PAN HD SS
SM 10-24 X 1/2 PH PAN TY F SS
Hex Blt 1/4-20 X 1/2 Full TH SS
Nut Hex 1/4-20 KEPS SS
2
2
4
4
1
1
8
2
2
2
Left panel
Installation Instructions
Assembly instructions for Freestanding application:
Loosen (2) front bottom grill screws (Fig. 01) approx. 1.
1/8”. (No need to remove screws.)
Tools Required
Phillips Screwdriver
5/16 Socket and 5/16 Wrench
Safety Glasses
Work Gloves
Top riser
Back panel
Screws
Right panel
Remove (2) top outer corner screws on back panel of 2.
refrigerated unit (Fig. 02). (Retain screw for re-use.)
Place the left side panel on the unit by sliding the 3.
front ange behind the bottom grill plate (Fig.03).
Then lift the rear of the panel so the screw holes
are visible in the slotted holes of panel, re-install
top screw and lower screw (Fig. 04 and 05)
(10-24 X 1/2 Hex Head SS - lower screws are
provided with hardware kit). Do not tighten at this
point.
Fig. 01
Screw
Screws
Fig. 02
1
Repeat Steps 2 and 3 for the other side panel. 4.
Place both top risers on top of unit as shown in (Fig. 07). 5.
Using screws provided (10-24 X 1-1/8 Pan Head SS), attach riser to the side panels. Take note of the 6.
alignment of the holes on the riser and side panel (Fig. 06).
Adjust the side panels to be level with the top of the refrigerated unit, then tighten all ange screws. 7.
The 4 male catch clips are preinstalled in the back panel. Feed the power cord thru the back panel and 8.
install protective grommet supplied with the hardware kit (Fig. 14).
Align the bottom male clips to the preinstalled female clips of the side panels, push at the outer corners to 9.
engage clips. See Fig. 08 for nal assembly.
Upper
Bottom front
ange
Fig. 03 Fig. 04
ange
Screw
Lower rear ange
Fig. 05
Female
cup
Ensure
holes
are
aligned
Fig. 06
Ensure
holes
are
aligned
top risers
Side View
Fig. 07
Ensure
holes
are
aligned
Top riser
Left panel
Fig. 08 Wrapper Kit Assembly shown with Refrigerated Drawers
Solid Surface Installation – Required Accessory (sold separately):
Solid Surface for Refrigerator and Refrigerated Drawer (WRT24RD) ■
Solid Surface for Beer Dispenser (WRT24T) ■
Locate holes on the solid surface and place onto the refrigerated 1.
unit so the holes align on the sides. Check for proper t and
alignment. Insert screws (10-24 X 1-1/8 PH SS) to anchor solid
surface to risers (Fig. 09). See Fig. 10 for nal assembly.
Final check to see that all spacing and gaps are even and level. The 2.
Refrigerated Drawer Unit (RF24D) must have the anti-tip device
installed. (Refer to the Installation Instructions that came with the
unit.)
Back panel
Right panel
Fig. 09
Solid surface
Assembly Instructions for Modular application (linked to a
CAD cart):
Remove the screws and the front bottom grill cover from the refrig-1.
erated unit and set them aside (Fig. 01).
2
Fig. 10
Loading...