DCS DishDrawer DD24SUT7, DishDrawer DD24SVT7 Installation Instructions Manual

US CA

INSTALLATION INSTRUCTIONS

DishDrawer

TM

dishwasher

DD24SUT7

590225A 10.11

3

SAFETY AND WARNINGS

1

WARNING!

Electrical hazard

Before installing the dishwasher, remove the house fuse or open the circuit

breaker. If permanently connecting the dishwasher, be sure the power is isolated
and the dishwasher unplugged.

GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of a malfunction or breakdown,
grounding will reduce the risk of electric shock by providing a path of least
resistance for electric current. This appliance is equipped with a cord having
an equipment-grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is installed and grounded in accordance
with all local codes and ordinances. WARNING - Improper connection of the
equipment-grounding conductor can result in a risk of electric shock. Check with
a qualified electrician or service representative if you are in doubt as to whether
the appliance is properly grounded.

If the dishwasher is installed as a permanently connected appliance:
GROUNDING INSTRUCTIONS - This appliance must be connected to a grounded
metal, permanent wiring system, or an equipment-grounding conductor must
be run with the circuit conductors and connected to the equipment-grounding
terminal or lead on the appliance.
Do not modify the power supply plug provided with the appliance - if it will not
fit the outlet, have a proper outlet installed by a qualified electrician. Do not use
an extension cord, adapter plug or multiple outlet box.

Failure to follow this advice may result in electrical shock or death.

WARNING!

Cut hazard

Take care - panel edges are sharp.

Failure to use caution could result in injury or cuts.

IMPORTANT SAFETY INSTRUCTIONS!

Installation of this dishwasher requires basic mechanical and electrical skills.
Be sure to leave these Instructions with the Customer.
Installation must comply with your local building, electricity, and plumbing regulations.
At the completion of the dishwasher installation, the Installer must perform the Final Checklist.
Remove all packaging materials supplied with the dishwasher.
This dishwasher is manufactured for indoor use only.
Ensure all water connections are turned OFF. It is the responsibility of the plumber and
electrician to ensure that each installation complies with all Codes and Regulations.
The dishwasher MUST be installed to allow for future removal from the enclosure if service is required.

The switched power outlet must be outside the dishwasher cavity, so that it is accessible after

installation.

Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to
the power supply cord and hoses.
If the dishwasher is to be relocated from one installation to another it must be kept upright to avoid
damage from water spillage.

Make sure only new hoses are used for connection (supplied with the dishwasher). Old hoses should

not be reused.
Failure to install the dishwasher correctly could invalidate any warranty or liability claims.

If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring the vehicle,

boat or mobile facility containing the product to the service shop at your expense or pay the service
technician’s travel to the location of the product.

SAVE THESE INSTRUCTIONS

4

PARTS SUPPLIED

2

Phillips
⁄” (16 mm)
screws (7)

1½ ” (38 mm)
bottom fixing
screws & metal
washers (2)

Drain hose
support (1)

Drain hose
joiner (1)

Side mounting
bracket kit
(A and B) (2)

OPTIONAL

If the Drain hose supplied is not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hoses by 11’ 10” (3.6m).

The kit is available from the nearest DCS by Fisher & Paykel Authorized Service Center, or Toll free 1.888.936.7872 or www.dcsappliances.com

Edge Protector (1)

(If the services hole is through
a metal partition the hole
must be protected with the
Edge protector supplied to
prevent damage to the power
cord or hoses.)

Wire clip (1)
(for securing

Drain hose joiner)

Moisture protection
tape (1)

(to prevent moisture
damage)

Clamp (1)
(for securing

Drain hose joiner)

Rubber
washer for
inlet hose (1)

(comes already
fitted)

5

OPTIONALLY HARD WIRING PRIOR TO INSTALLATION

9

12

11

11

10

4

5

6

7

7

8

8

3a

3c

3

3b

REMOVE THE DRAWER

TERMINATE THE WIRING AS SHOWN

REMOVE THE ACCESS COVER & POWER CORD

Remove knock-out for cable clamp and
fit a suitable cable clamp for the conduit.

Use copper conductors only.

2

100 mm

1

3

4

5

To prevent kinked hoses, we recommend
rotating the drawer counter-clockwise
and resting it on its side after removal.

Product may move.
Mark chassis position
on cavity

Access
cover

Press the release tabs in on
either side and push back
to release drawer from
runners.

3

4” (100mm)

18

19

15

16

17

Before refitting the drawer,
ensure the hoses are not
twisted and the latches at
the rear of each drawer
runner are facing forward.

Ensure the release tabs on
both sides are reset fully.

Ensure the drawer
is now rotated
clockwise back.

13

14

15

16

17

Pull forward the release tabs
on both sides 4”(100

mm)

3d

REFIT THE DRAWER ONTO THE RUNNERS & CLOSE

Electrical Shock Hazard

Before continuing, ensure that the product is
disconnected from the power supply.

Failure to follow this warning may result in
electrical shock, injury or re.

WARNING!