DCS DD24SVT7 Installation Manual

INSTALLATION INSTRUCTIONS

DishDrawer

DD24SUT7 and DD24SVT7

dishwasher

models

US CA

590225B 04.14

SAFETY AND WARNINGS

WARNING!

Electrical hazard

Before installing the dishwasher, remove the house fuse or open the circuit

breaker. If permanently connecting the dishwasher, be sure the power is isolated and the dishwasher unplugged.

GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances. WARNING - Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt as to whether the appliance is properly grounded.

If the dishwasher is installed as a permanently connected appliance: GROUNDING INSTRUCTIONS - This appliance must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. Do not modify the power supply plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use an extension cord, adapter plug or multiple outlet box.

Failure to follow this advice may result in electrical shock or death.

WARNING!

Cut hazard

Take care - panel edges are sharp.

IMPORTANT SAFETY INSTRUCTIONS!

Installation of this dishwasher requires basic mechanical and electrical skills. Be sure to leave these Instructions with the Customer. Installation must comply with your local building, electricity, and plumbing regulations. At the completion of the dishwasher installation, the Installer must perform the Final Checklist. Remove all packaging materials supplied with the dishwasher. This dishwasher is manufactured for indoor use only. Ensure all water connections are turned OFF. It is the responsibility of the plumber and electrician to ensure that each installation complies with all Codes and Regulations. The dishwasher MUST be installed to allow for future removal from the enclosure if service is required.

The switched power outlet must be outside the dishwasher cavity, so that it is accessible after

installation.

Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord and hoses. If the dishwasher is to be relocated from one installation to another it must be kept upright to avoid damage from water spillage.

Make sure only new hoses are used for connection (supplied with the dishwasher). Old hoses should

not be reused. Failure to install the dishwasher correctly could invalidate any warranty or liability claims.

If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring the vehicle,

boat or mobile facility containing the product to the service shop at your expense or pay the service technician’s travel to the location of the product.

The DCS by Fisher & Paykel DishDrawer dishwasher is designed for connection to the national power

supply grid. In some instances connection to off-grid alternative energy systems, such as wind, solar and stand alone generation, may result in damage to the electronic control of the appliance. Any damage to the control as a direct consequence of connection to alternative energy sources will not be covered under the terms of the Warranty.

SAVE THESE INSTRUCTIONS

Failure to use caution could result in injury or cuts.

PARTS SUPPLIED

Drain hose support (1)

Edge Protector (1)

(If the services hole is through a metal partition the hole must be protected with the Edge protector supplied to prevent damage to the power cord or hoses.)

Drain hose joiner (1)

Wire clip (1) (for securing

Drain hose joiner)

Side mounting bracket kit (A and B) (2)

OPTIONAL

Clamp (1) (for securing

Drain hose joiner)

Phillips ⁄” (16 mm) screws (7)

1½ ” (38 mm) bottom fixing screws & metal washers (2)

If the Drain hose supplied is not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hoses by 11’ 10” (3.6m).

The kit is available from the nearest DCS by Fisher & Paykel Authorized Service Center, or Toll free 1.888.936.7872 or www.dcsappliances.com

Rubber washer for inlet hose (1)

(comes already fitted)

Moisture protection tape (1)

(to prevent moisture damage)

100 mm

OPTIONALLY HARD WIRING PRIOR TO INSTALLATION

REMOVE THE DRAWER

Product may move. Mark chassis position on cavity

4” (100mm)

TERMINATE THE WIRING AS SHOWN

Press the release tabs in on either side and push back to release drawer from runners.

Remove knock-out for cable clamp and fit a suitable cable clamp for the conduit.

Access cover

To prevent kinked hoses, we recommend rotating the drawer counter-clockwise and resting it on its side after removal.

REMOVE THE ACCESS COVER & POWER CORD

Electrical Shock Hazard

Before continuing, ensure that the product is disconnected from the power supply.

Failure to follow this warning may result in electrical shock, injury or re.

REFIT THE DRAWER ONTO THE RUNNERS & CLOSE

WARNING!

Pull forward the release tabs on both sides 4”(100

mm)

Ensure the drawer is now rotated clockwise back.

Before refitting the drawer, ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward.

Use copper conductors only.

Ensure the release tabs on both sides are reset fully.

+ 10 hidden pages