DCS CADBNDT Installation Manual

SOLID SURFACE FOR OUTDOOR BEER DISPENSER, REFRIGERATOR,

REFRIGERATED DRAWERS, ICE MAKER, BEND UNIT AND

BEND UNIT BRACKET

INSTALLATION INSTRUCTIONS

Before you begin, read these instructions completely and carefully.

Getting Started

Remove packaging and retain until installation is complete.

WARNING!

Some parts have sharp edges; care must be taken when handling the various components to
avoid injury. Please read safety information provided in these instructions before beginning
assembly. Wear gloves when handling.

Contents

Part Description Qty

Screws MS 10-24 X 1-1/8 PH PAN HD SS (for Refrig-

erator, Refrigerator Drawers and Ice Maker only)

Flat Washer (for Beer Dispenser only) 4

Screws MS 10-24 X 1-1/8 PH PAN HD SS

(for Beer Dispenser only)

Hex Nut 10-24 KEPS (for Beer Dispenser only) 4

Solid Surface

Note: Some parts may not be used in your conguration.

4

8

1

Tool Required

Phillips Screwdriver

5/16 Socket

Safety Glasses

Work Gloves

Installation Instructions

Solid Surface Installation

Locate holes on the solid surface and place on to the refrigerated unit. Ensure side holes align on the 1.
refrigeration units. Check for proper t and alignment. Insert screws (10-24 X 1-1/8 PH SS) to anchor solid
surface to risers (Fig. 02).

Solid Surface

Riser

Fig. 01

Final check to see that all gaps are spaced even and level. 2.

Fig. 02

Solid Surface Installation for Beer Dispenser Only

Mount the draft tower onto the solid surface using the four screws, nuts, 1.
washers (provided) and one mounting gasket (part of draft tower kit in the
Beer Dispenser)(Fig. 03 and 04).

Gasket

Fig. 03

Fig. 04

Over. . .

Important:

The hole in the top of the refrigerated unit must be sealed to prevent air leak using some
insulating foam rubber (not included).

Care and Maintenance

EASY DAILY CLEANING AND MAINTENANCE

Water stains or a small quantity of smears may be removed easily by using a wet cloth and a little household
cleaner, mild detergent or soapy water.

THE SURFACE

The surface can be cleaned with ne gauze with soap and water. Commonly used glass cleaners are the best
agent to keep the surface clean and shiny.

MINOR STAINS OR SCRATCHES

May be eliminated by rubbing with a mild detergent and cloth. Larger scratches may be eliminated with ne
sand paper (800-1000 grit). The surface gloss will be restored after it is rubbed with cloth and water.

SERIOUS STAINS, CIGARETTE BURNS OR SCORES

Stains or scores may be eliminated with sandpaper and water and polished with a polishing machine (buer).
With regard to more serious damage, please contact professional distributors who know techniques and
possess equipment for repairing scratches.

USE AND FOOD SAFETY

The surface is smooth, so there is nowhere for bacteria or pathogens to hide. It is NSF certied and allows for
direct contact with food. However, we would still recommend you clean it before use and do not put other food
where raw meat is present until the area is completely cleaned. Cleaning with a diluted household disinfectant
will provide extra health protection.

USING HOT PADS

The surface is heat resistant and remains stable and undamaged below a temperature of 212º F (100º C);
however, high temperature and ame may scorch the countertop. This kind of damage can be removed under
most circumstances, but the use of a hot pad or insulated material on the surface will protect the countertop.

CUTTING

Direct cutting on the surface should be avoided.

SUDDEN HEATING

Heat proof pads should be used when placing boiling pots of water on the surface.

STRONG STAINS

The surface can resist most stains and corrosion, but strong chemical agents, bathroom detergents, derusting
agents, turpentine, and water pipes containing acid will produce blotches when they are placed on the surface
for a long time.

IMPACT

Avoid heavy items falling on the surface countertops to prevent ugly scratches or cracked countertop.

FLAMES
Avoid a ame contacting the surface directly.

WATER RESISTANCE

Although the surface is water resistant and its water absorption is very low, excessive stagnant water should be
avoided. Avoid placing a wet cloth or towel on the surface for a long time. Keep the surface as dry as possible
because water could contain contaminants which cause white spots to appear on the surface after a long
exposure. Under such circumstances, wipe the surface as soon as possible and blow-dry with a hair dryer.

Fisher & Paykel Appliances, Inc.
5900 Skylab Road, Huntington Beach, CA 92647

Customer Care: 888.281.5698 • Fax: [phone]

www.dcsappliances.com

P/N 242280 RA 5/08