DCS BGCU, BGRU User Manual
Backguard for professional
ranges and cooktops
Models BGRU and BGCU
Dosseret pour cuisinières et
tables de cuisson professionnelles
Modèles BGRU et BGCU
Installation instructions
Guide d’installation
US CA
A MESSAGE TO OUR CUSTOMERS
Thank you for selecting this Backguard System. Because of the unique features of this accessory we have
developed this Installation Guide. It contains valuable information on how to install your new Backguard System.
Keep this guide handy, as it will help answer questions that may arise as you use your new accessory.
For your convenience, product questions can be answered by a DCS Customer Care Representative by phone:
1-888-
936-7872
NOTE: Inspect the product to verify that there is no shipping damage. If any damage is detected, call the shipper
and initiate a damage claim. DCS by Fisher & Paykel is not responsible for shipping damage.
DO NOT discard any packing material (box, pallet, straps) until the unit has been inspected.
WARNING!
Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death.
Read the installation, operating and maintenance instructions thoroughly before installing, using or servicing this
equipment.
, or email:
customer.care@fisherpaykel.com
.
1
US
CA
WARNING!
If the information in this manual is not followed exactly, a fire or explosion may result causing property damage,
personal injury or death.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
DANGER
If You Smell Gas:
1. Do not try to light any appliance.
2. Do not touch any electrical switch; do not use any phone in your building.
3. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
4. If you cannot reach your gas supplier, call the fire department.
5. Installation and service must be performed by a qualified installer, service agency or the gas supplier.
WARNING!
To reduce the risk of injury to persons in the event of a cooktop grease fire, observe the following: Turn burner off
first. Smother flames with a close-fitting lid, cookie sheet, metal tray, baking soda or use a dry chemical or foam-type
fire extinguisher. Be careful to prevent burns. If the flames do not go out immediately evacuate and call the fire department. Never pick up a flaming pan - You may be burned. DO NOT USE WATER ON GREASE FIRES, including wet
dishcloths or towels - a violent steam explosion will result. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate it.
2. The fire is small and contained in the area where it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit.
WARNING!
Do not place items of interest to children on racks or appliance. Children could be seriously injured if they should
climb onto or into the appliance to reach these items.
WARNING!
Do not place combustible material (paper, cloth, plastic, etc.) on the rack.
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.
US
CA
2
TABLE OF CONTENTS
Backguards for ranges – BGRU models
SPECIFICATIONS 4
RANGE MOUNT STANDARD BACKGUARD INSTALLATION 4
WALL MOUNT FULL BACKGUARD INSTALLATION 5
Backguards for cooktops – BGCU models
SPECIFICATIONS 8
WALL MOUNT STANDARD BACKGUARD INSTALLATION 8
3
US
CA
WALL MOUNT FULL BACKGUARD INSTALLATION 9
US
CA
SPECIFICATIONS
4
8-3/4 "
12 "
MODEL A RACK (13-5/8”) QTY. RACK (16-5/8”) QTY.
BGRU-3030 29-7/8” 2 -
WALL MOUNT FULL BACKGUARDS
26-1/2 "
BGRU-3036 35-7/8” - 2
BGRU-3048 47-7/8” 2 1
A
8-1/2 "
1-5/16 "
RANGE MOUNT STANDARD BACKGUARDS
MODEL A
BGRU-1230 29-7/8”
A
BGRU-1236 35-7/8”
BGRU-1248 47-7/8”
BACKGUARDS FOR RANGES - BGRU MODELS
1-5/16 "
RANGE MOUNT STANDARD BACKGUARD
INSTALLATION
1. Unpack the backguard and screw the front section onto the back section, as shown (Fig. 01)
2. Align the backguard with the range, so that it rests on the island trim. Fasten the bottom of the backguard to the
rear of the range using all the screws provided, as shown (Fig. 02). The two center screws come already attached
to the range for your convenience.
Front Section
Back Section
# 8
Self-tapping
sheet metal
screws
Screw is loosened
Fig.01
Fig.02
WALL MOUNT FULL BACKGUARD INSTALLATION
RECOMMENDED INSTALLATION ORDER:
1) VENT HOOD 2)BACKGUARD SYSTEM 3) RANGE
1. Locate and level range per installation instructions.
2. After unpacking all backguard system parts, locate the Back Section 1/4” (see fig. 03) above and centered over
the Island Trim attached to the range.* Secure Back Section to wall with the appropriate fasteners (not supplied)
to anchors or wood stud (fig. 03).
WARNING:
The Back Section must be securely fastened to the wall. Failure to do so could cause damage or personal injury if
the Backguard was to pull free from wall when racks are loaded. The maximum weight placed on each rack should
be 10 lbs.
*After 1/4” is located, slots in back section may be used to adjust spacing between range island trim and
backguard for a flush fit.
3. Attach rod, end caps and center stanchion to Front Section of backguard with #10 machine screws supplied
(fig. 04).
4. Bend wedge-shaped tabs down on top of the front section approximately 3/16”. When mounting the front
section, insure that these tabs engage the mating holes in the top of the rear section (see fig. 05, page 4).
5. Secure Front Section of backguard to Back Section with #8 self-tapping sheet metal screws supplied
(fig. 05, page 4).
5
US
CA
BACKGUARDS FOR RANGES - BGRU MODELS
6. Attach racks to rod (fig. 06, page 4). The maximum weight placed on each rack should be 10 lbs.
Bend down approx. 3/16”
Back Section
Front Section
End
Cap
Slots to choose
desired spacing
between Range Island
Trim and Backguard.
16” for 30” Range
32” for 36/48” Range
1/4”
Island
Trim
Center
Stanchion
Rod
End
Cap
#10
Machine
Screws
Fig.03
Fig.04
US
CA
WALL MOUNT FULL BACKGUARD INSTALLATION
6
Front Section
Tabs*
BACKGUARDS FOR RANGES - BGRU MODELS
Holes*
Back Section
Rack
#8
Selftapping
sheet
metal
screws
Fig.05 Fig.06
*Insure tabs and holes engage to secure top of backguard.
CARE AND MAINTENANCE
This is made of stainless steel. Use the mildest cleaning procedure first. Hot soapy water, rinse and dry. If
the panel has food soil remaining, try a general kitchen cleaner, such as Fantastik®, Simple Green® or Formula
409®. Apply cleaner with a damp sponge, rinse thoroughly and dry. Always scrub lightly in the direction of the
grain. Do not use a steel wool pad, it will scratch the surface. To touch up noticeable scratches in the stainless
steel, sand very lightly with dry 100 grit emery paper, rubbing in the direction of the grain. After cleaning use
a stainless steel polish, such as Stainless Steel Magic®. If the rear top burners are used extensively on high it is
possible for the vertical stainless steel panel to discolor from the burner heat. This discoloration can be removed
by using Revere Ware Stainless Steel Cleaner.
Loading...