Dcs Bga26-bql Owner's Manual
THE PROFESSIONAL
26” BGA GRILL
Use and Care Guide
MODEL:
BGA26-BQ
1
Thank you for selecting this DCS Professional “BGA” Series Grill. Because of these appliances’ unique
features we have developed this Use and Care Guide.It contains valuable information on how to properly
operate and maintain your new grill for years of safe and enjoyable cooking.
To help serve you better,please fill out and submit your Ownership Registration Card by visiting our website
at www.dcsappliances.com and selecting “Customer Service” on the home page and then select
“Ownership Registration” or submit the enclosed Ownership Registration Card to the address below. In
addition, keep this guide handy, as it will help answer questions that may arise as you use your new
appliance.
For your convenience, product questions can be answered by a DCS Consumer Service Representative at
1-888-281-5698, email:support@dcsappliances.com, or by mail:
WAR NI NG
Improper installation, adjustment alteration, service or maintenance can
cause property damage, injury or death. Read the installation, operating and
maintenance instructions thoroughly before use, installing or servicing this
equipment. For outdoor use only.
PRECAUTION
Do Not store or use gasoline or any other flammable vapors and liquids in the
vicinity of this or any other appliance.
FOR YOUR SAFETY
IF YOU SMELL GAS:
1. Shut off gas to the appliance.
2. Extinguish any open flames.
3. If odor continues, immediately call your gas supplier.
P
LEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.
DCS
Attention: Customer Service
5800 Skylab Road
Huntington Beach, CA 92647
A MESSAGE TO OUR CUSTOMERS
2
SAFETY PRACTICES & PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
GRILL MODEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
GAS REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-9
LOCATING GRILL / BUILT-IN CLEARANCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-10
BUILT-IN CONSTRUCTION DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
LEAK TESTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
INSTALLER FINAL CHECKLIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
BURNER ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-14
USING THE GRILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-16
LIGHTING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
CARE & CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
BURNER REMOVAL AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
PA RT S LISTS
Grill Burner Assembly / Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Grill Body Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Grill Cart Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Cart Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
WIRING DIAGRAM
Wiring Diagram for BGA26-BQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
WAR RANT Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
TABLE OF CONTENTS
33
IMPORTANT SAFETY NOTICE:
Certain Liquid Propane dealers may fill liquid propane cylinders for use in the
grill beyond cylinder filling capacity. This “Overfilling” may create a
dangerous condition.
“Overfilled” tanks can build up excess pressure. As a safety device, the tanks pressure relief valve will
vent propane gas vapor to relieve this excess pressure. This vapor is combustible and therefore can
be ignited. To reduce this danger, you should take the following safety precautions:
1. When you have your tank filled,be sure you tell the supplier to fill it to no more than 3/4 (75%)
of its total capacity.
2. If you own or use an extra spare tank, or have a disconnected tank, you
should NEVER store it near or under the grill unit or heat box, or near
any other ignition or heat source. A metallic sticker with this warning
is attached to the grill to remind you, your family and all others who
may use your BBQ grill of these safety precautions.
Do not remove this sticker.
WAR NING
:
Do not try lighting this appliance without reading the
“LIGHTING INSTRUCTIONS” section of this manual.
This Grill is for outdoor use only.
WAR NING:
Push and hold the igniter button, turn the selected burner knob to “HI”. If
burner does not light in 4 to 5 seconds turn knob “OFF” and wait 5 minutes
before trying again for any accumulated gas to dissipate.
CAUTION:
Children should not be left alone or unattended in an area where the grill is
being used. Never allow them to sit,stand or play on or around the grill at any
time. When in use,portions of the grill get hot enough to cause severe burns.
■ Do not store items of interest to children around or below the grill, in the cart or masonry
enclosure. Never allow children to crawl inside a cart or enclosure.
■ Never let clothing,pot holders or other flammable materials come in contact with or too close
to any grate, burner or hot surface until it has cooled. Fabric may ignite and result in personal
injury.
■ Do not heat unopened food containers as a build-up of pressure may cause the container to
burst.
■ Always use a covered hand when opening the grill lid and only do so slowly to allow heat and
steam to escape.
SAFETY PRACTICES & PRECAUTIONS
4
For personal safety, wear proper apparel. Loose fitting garments or sleeves should never be worn
while using this appliance. Some synthetic fabrics are highly flammable and should not be worn while
cooking. Only certain types of glass, heat-proof glass ceramic, earthenware, or other glazed utensils
are suitable for grill use. Use of these types of materials may break with sudden temperature changes.
Use only on low or medium heat settings according to the manufacturer’s directions.
WAR NING:
Spiders and insects can nest in the burners of this and any other grill, and
cause the gas to flow from the front of the burner. This is a very dangerous
condition which can cause a fire to occur behind the valve panel, thereby
damaging the grill and making it unsafe to operate.
WAR NING:
Keep the area surrounding the grill free from combustible materials, trash, or
combustible fluids and vapors such as gasoline or charcoal lighter fluid. Do
not obstruct the flow of combustion and ventilation air.
WAR NING:
Never use the grill in windy conditions. If located in a consistently windy area
(oceanfront, mountaintop, etc.) a wind break will be required. Always adhere
to the specified clearances listed.
■ Never lean over an open grill. When lighting a burner, always pay close attention to what you
are doing. Be certain you are pushing the igniter labeled for the burner you intend on using.
■ When using the grill,do not touch the grill rack, burner grate or immediate surrounding area as
these areas become extremely hot and could cause burns.
■ Grease is flammable. Let hot grease cool before attempting to handle it. Avoid letting grease
deposits collect in the drip pan. Clean often.
■ Do not use aluminum foil to line drip pans or grill racks. This can severely upset combustion air
flow or trap excessive heat in the control area. The result of this can be melted knobs and/or
damaged ignition and gas control components.
■ Begin by insuring proper installation and servicing. Follow the installation instructions
provided with this product. Have your grill installed by a qualified technician. Have the installer
show you where the gas supply shut off valve is located so that you know where to shut off the
gas to the grill. If you smell gas, your installer has not done a proper job of checking for leaks.
If the connections are not perfectly seated and tightened, you can have a small leak and
therefore a faint gas smell. Finding a leak is not a “do-it-yourself ” procedure. Some leaks can
only be found with the burner control in the “on”position and this must be done by a qualified
technician.
SAFETY PRACTICES & PRECAUTIONS
5
■ Clean the grill with caution. Avoid steam burns; do not use a wet sponge or cloth to clean the
grill while it is hot. Some cleaners produce noxious fumes or can ignite if applied to a hot
surface.
■ Be sure all grill controls are turned off and the grill is cool before using any type of aerosol
cleaner on or around the grill. The chemical that produces the spraying action could, in the
presence of heat, ignite or cause metal parts to corrode.
■ Do not use the grill for cooking excessively fatty meats or products which promote flare-ups.
■ Never grill without the drip pan in place and pushed all the way to the back of the grill. Without
it hot grease could leak downward and produce a fire or explosion hazard.
■ Do not operate the grill under unprotected combustible construction. Use only in well
ventilated areas. Do not use in buildings, garages, sheds, breezeway or other such enclosed
areas. This unit is for outdoor use only.
■ If a cart unit is stored indoors ensure that it is cool, fold the side shelf down, then push, never
pull, the grill. If LP, the cylinder must be unhooked and the LP cylinder stored outside in a well
ventilated area, out of reach of children.
■ Do not use charcoal in the grill. Never use the grill in a windy area. Keep any electrical supply
cord, or the rotisserie motor cord away from the heated areas of the grill.
■ Never use a dented or rusty LP tank. Keep the ventilation openings of the cylinder enclosure
free and clear from debris.
■ Use only dry potholders; moist or damp potholders on hot surfaces may cause burns from
steam. Do not use a towel or bulky cloth in place of potholders. Do not let potholders touch
hot portions of the grill rack or burner grate.
■ CALIFORNIA PROPOSITION 65-WARNING: The Burning of gas cooking fuel generates some by
products which are on the list of substances which are known by the State of California to cause
cancer or reproductive harm. California law requires businesses to warn customers of potential
exposure to such substances. To minimize exposure to these substances always operate this
unit according to the use and care manual, ensuring you provide good ventilation when
cooking with gas.
SAFETY PRACTICES & PRECAUTIONS
PREFERRED AIR FLOW
GRILL EXHAUST
EXHAUST
FLAME
BURNER
WIND
WIND
PRIMARY
INTAKE
AIR FLOW
EXHAUST VENT FLOW
GRILL PLACEMENT
6
GRILL MODEL
BGA26-BQ
7
GAS REQUIREMENTS
Verify the type of gas supply to be used,
either natural or LP, and make sure the
marking on the appliance rating plate
agrees with that of the supply. The rating
plate is located on the inside back wall of
the Grill. Never connect an unregulated
gas line to the appliance.
An installer supplied gas shut-off valve
must be installed in an easily accessible
location. All installer supplied parts must
conform to local codes, or in the absence
of local codes, with the National Electrical
Code, ANSI/NFPA 70-1990, and the
National Fuel Gas Code, ANSI Z223.1-
1988.
All pipe sealants must be an approved
type and resistant to the actions of LP
gases. Never use pipe sealant on flare
fittings. All gas connections should be
made by a competent technician and in accordance with local codes and ordinances. In the absence
of local codes, the installation must comply with the national fuel gas code ANSI Z223.1-1988. Gas
conversion kits are available from the factory. When ordering gas conversion kits have the model
number,and the type of gas (natural or LP) from your grill.
TOTAL GAS CONSUMPTION OF THE GRILL WITH ALL BURNERS ON HI:
BGA26-BQ - 33,000 Btu/hr
The appliance and its individual shut-off valve must be disconnected from the gas supply piping
system during any pressure testing of that system at test pressures in excess of 1/2 PSIG (3.5 kPa.).
The appliance must be isolated from the gas supply piping system by closing its individual manual
shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to
or less than 1/2 PSIG (3.5 kPa.). The installation of this appliance must conform with local codes or,in
the absence of local codes, with the national fuel gas code,ANSI Z223.1a-1988. Installation in
Canada must be in accordance with the Standard Can1-b149.1 and/or .2 (installation code for gas
burning appliances and equipment) and local codes.
NATURAL GAS HOOK UP:
Connection: 1/2" NPT male with 3/8" flare adapter. Operating pressure: 4.0" W.C.
Supply pressure: 5" to 14" water column. If in excess of 14" W.C. a step down regulator is required.
Check with your local gas utility company or with local codes for instructions on installing gas supply
lines. Be sure to check on type and size of run, and how deep to bury the line. If the gas line is too
small, the grill will not function properly. Any joint sealant used must be an approved type and be
resistive to the actions of LP gases.
FIG.01 Natural Gas (26BQR Shown)
Coupling
1/2 NPT
Close
NIpple
Regulator
4.0" W.C.
Adapter 1/2 NPT
to 3/8 flare fitting
Do not put threading
compound on these
threads
*Installation must conform with
local codes or with the National
Fuel Gas Code ANSI Z223.1
Bottom of unit
Threading compound
must be resistant to LP gas
1/2 NPT
Close
NIpple
Installer supplied shut-off
valve must be easily
accessible*
8
GAS REQUIREMENTS
TO HOOK-UP THE FITTINGS SUPPLIED WITH THE GRILL:
Assemble as shown (Fig.01). Use threading compound on male threads only. Do not use threading
compound on the male end of the 1/2 NPT to 3/8 flare adapter. Use a second pipe wrench to hold the
grill inlet pipe to avoid shifting any internal gas lines of the grill. Ensure that the regulator arrow points
in the direction of gas flow towards the unit,away from the supply. Do not forget to place the installer
supplied gas valve in an accessible location.
LP GAS HOOK UP (TYPE 1 OR QCC1 REGULATOR):
Grills orificed for use with LP gas come equipped with a high capacity hose/regulator assembly for
connection to a standard 20 lb. LP cylinder (Type 1). The LP tank is not included.
Connection: 1/2" NPT male with a 3/8" Flare adapter (included). LP Hose with a quick disconnect and
fittings are included. Operating pressure: 10.0" W.C.
To connect the LP regulator/hose assembly to the tank/valve assembly,first make sure the main valve
on the tank is completely closed. Although the flow of gas is stopped when the Type 1 system is
disconnected as part of of its safety feature, you should always turn the LP tank main valve (Fig.02) off
after each use and during transport of the tank or unit. Insert the regulator inlet into the tank valve
and turn to the black coupler clockwise until the coupler tightens up. Do not overtighten the
coupler.
Turn the main tank valve on and turn the burner control valves on the unit to the “HI”
position for about 20 seconds to allow the air in the system to purge before attempting to light the
burners.
To disconnect the coupler, first make sure the main tank valve is turned off. Grasp the coupler and turn
counter clockwise. The inlet will then disengage,remove the inlet from the tank valve opening if it has
not already done so when it disengaged. Your local LP filling station should be equipped with the
proper equipment to fill your tank.
LP TANK REQUIREMENTS:
A dented or rusty LP tank may be hazardous and should be checked by your LP supplier. Never use
a cylinder with a damaged valve. Always check for leaks after every LP tank change. The LP gas
cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders of
the U.S. Department of Transportation (DOT) and designed for use with a Type 1 system only. Do not
FIG.02 LP Gas (26BQR Shown)
Adapter 1/2 NPT
to 3/8 flare fitting
Do not put threading
compound on these
threads
LP Regulator hose
assembly 10" W.C.
*Installation must conform with
local codes or with the National
Fuel Gas Code ANSI Z223.1
Bottom of unit
Threading compound
must be resistant to LP gas
Type 1 Regulator
Main Valve
Type 1 Tank
Loading...