KSLi-SUB/KSLi-GSUB
- perliminary -
SL
Manual 1.1 en
General information
KSLi-SUB/KSLi-GSUB Manual - perliminary -
Version: 1.1 en, 01/2020, D2733.EN .01
Copyright © 2020 by d&b audiotechnik GmbH & Co. KG; all
rights reserved.
Keep this document with the product or in a safe place
so that it is available for future reference.
When reselling this product, hand over this document to the new
owner.
d&b audiotechnik GmbH & Co. KG
Eugen-Adolff-Str. 134, D-71522 Backnang, Germany
T +49-7191-9669-0, F +49-7191-95 00 00
docadmin@dbaudio.com, www.dbaudio.com
Contents
1 Safety precautions.............................................................. 4
1.1 Information regarding the use of loudspeakers........................ 4
1.2 d&b ArrayCalc............................................................................ 5
2 KSLi-SUB/KSLi-GSUB loudspeaker............................... 6
2.1 Intended use................................................................................ 6
2.2 Connections................................................................................ 7
2.3 Operation.................................................................................... 8
2.3.1 Controller settings.................................................................... 8
2.4 Technical specifications.............................................................. 8
3 Manufacturer's declarations......................................... 10
3.1 EU conformity of loudspeakers (CE symbol).......................... 10
3.1.1 WEEE Declaration (Disposal).............................................. 10
d&b KSLi-SUB/KSLi-GSUB Manual 1.1 en - perliminary - 3
1 Safety precautions
1.1 Information regarding the use of loudspeakers
Potential risk of personal injury
Never stand in the immediate vicinity of loudspeakers driven at a
high level. Professional loudspeaker systems are capable of
causing a sound pressure level detrimental to human health.
Seemingly non-critical sound levels (from approx. 95 dB SPL) can
cause hearing damage if people are exposed to it over a long
period.
In order to prevent accidents when deploying loudspeakers on the
ground or when flown, please take note of the following:
▪ When setting up the loudspeakers or loudspeaker stands, make
sure they are standing on a firm surface. If you place several
systems on top of one another, use straps to secure them
against movement.
▪ Only use accessories which have been tested and approved by
d&b for assembly and mobile deployment. Pay attention to the
correct application and maximum load capacity of the
accessories as detailed in our specific "Mounting instructions" or
in our "Flying system and Rigging manuals".
▪ Ensure that all additional hardware, fixings and fasteners used
for installation or mobile deployment are of an appropriate size
and load safety factor. Pay attention to the manufacturers'
instructions and to the relevant safety guidelines.
▪ Regularly check the loudspeaker housings and accessories for
visible signs of wear and tear, and replace them when
necessary.
▪ Regularly check all load bearing bolts in the mounting devices.
Potential risk of material damage
Loudspeakers produce a static magnetic field even if they are not
connected or are not in use. Therefore make sure when erecting
and transporting loudspeakers that they are nowhere near
equipment and objects which may be impaired or damaged by an
external magnetic field. Generally speaking, a distance of 0.5 m
(1.5 ft) from magnetic data carriers (floppy disks, audio and video
tapes, bank cards, etc.) is sufficient; a distance of more than 1 m
(3 ft) may be necessary with computer and video monitors.
d&b KSLi-SUB/KSLi-GSUB Manual 1.1 en- perliminary -4
d&b ArrayCalc
1.2 d&b ArrayCalc
For both safety and acoustic reasons, d&b line arrays must be
designed using the d&b ArrayCalc simulation software. The
software is available as a native stand-alone application for both
Microsoft Windows and Mac OS X operating systems and can be
downloaded at www.dbaudio.com.
Detailed information on how to use and operate ArrayCalc is
provided by the Help system of the software. To access the Help
system, press F1 or select the Help button (
) from
the ArrayCalc toolbar. This will launch the HelpViewer which
provides an overview of the program as well as a search function
and direct access to the related topics.
In addition, ArrayCalc will provide you with typical array
configurations within the permitted load limits and will help you get
familiar with the mechanical load conditions and limitations.
d&b TI 385
Further information on line array design can be found in "TI 385
d&b Line array design, ArrayCalc". The TI is supplied with the
software or can be downloaded from the d&b website at
www.dbaudio.com.
d&b Seminar
We also recommend you to attend the regularly hosted d&b Line
array training seminars. Further information regarding the d&b
seminars and a seminar schedule can also be found on the d&b
website at
www.dbaudio.com.
d&b Video tutorials
In addition d&b provides related video tutorials which can also be
found on the d&b website at www.dbaudio.com or
www.sl-series.com.
d&b KSLi-SUB/KSLi-GSUB Manual 1.1 en - perliminary - 5
2 KSLi-SUB/KSLi-GSUB loudspeaker
2.1 Intended use
NOTICE!
Only operate d&b SL-Series loudspeakers with the specified and
correctly configured d&b amplifiers, otherwise there is a risk of
damaging the loudspeaker components and the directional
characteristics of the system cannot be achieved.
Applicable d&b amplifiers: 40D
Product description
The KSLi-SUB and KSLi-GSUB are installation specific cardioid
subwoofers for the KSLi sytsem. They can be used to supplement
KSLi8 and KSLi12 cabinets, either flown (KSLi-SUB) or ground
stacked (KSLi-GSUB).
When the Z5744 KSLi-SUB Mounting frame is used, KSLi-SUB
cabinets can be flown as pure SUB columns or in mixed arrays in
connenction with KSLi-TOP cabinets using the additional Z5745
KSLi-SUB Mounting adapter.
Both cabinets are actively driven, 2-way bass-reflex designs
housing three long excursion neodymium 15“ drivers. Two drivers
face to the front while one driver radiates to the rear of the cabinet.
Front and rear drivers are driven by separate amplifier channels
and operate in independent bass reflex chambers. Through its
cardioid dispersion pattern, this setup avoids unwanted energy
behind the system and greatly reduces the reverberant field at low
frequencies providing highest accuracy in low frequency
reproduction. The frequency response extends from 36 Hz to
105 Hz (33 Hz to 75 Hz - INFRA mode).
The cabinet enclosures are constructed from marine plywood and
have an impact and weather protected PCP (Polyurea Cabinet
Protection) finish. The front and rear of the cabinets are protected
by rigid metal grills. Each side panel incorporates two slots to
accept dedicated lifting pins (T-handles). During setup, these pins
serve as a temporary lifting aid and can be inserted and locked
when needed.
Four rubber feet prevent cabinet movement and protect the bottom
panel against scratching. Correspondingly shaped recesses in the
top panel of the cabinet prevent cabinet movement when stacking
KSLi-GSUBs or KSLi-SUBs.
The KSLi-SUB cabinet incorporates front and rear rigging strands
while the KSLi-GSUB comes without any rigging components and is
intended for ground stacked purposes.
Rigging components and arrays
Cabinets are mechanically connected using the rigging strands on
both sides of the cabinet front and a central strand at the rear of
the cabinet. All necessary rigging components are mounted on the
cabinet and fold out or slide out when needed.
A detailed description of the rigging components is given in the
respective rigging manuals.
d&b KSLi-SUB/KSLi-GSUB Manual 1.1 en- perliminary -6
Cardioid dispersion pattern
Cardioid dispersion
Cardioid dispersion avoids unwanted energy behind the system
and greatly reduces the excitation of the reverberant field at low
frequencies providing the greatest accuracy of low frequency
reproduction. The subwoofers can be used as stand-alone solutions
or in stacked combinations with a minimum distance of 60 cm (2 ft)
between adjacent cabinets or between the subwoofers and a side
wall. When positioned in front of walls, the minimum distance to
rear walls is maintained by the wheels mounted at the rear of the
cabinet.
2.2 Connections
The cabinets are fitted with a single NLT4 F connector using the pin
assignment 1+/1– for the front drivers and pins 2+/2– for the
rear driver.
Phoenix option
Connector wiring
NLT4 F
Phoenix option
NOTICE!
Risk of damage to the system components!
Different pin assignment on the loudspeaker and amplifier.
Þ Please refer to the corresponding amplifier manual.
Cabinets with Phoenix option are fitted with a 4-pole Phoenix
connector socket (Type: DFK PC 4/4 GF) using the following pin
assignment:
▪ Pins 1+/2– feeding the forward LF drivers.
▪ Pins 3+/4– feeding the rear LF driver.
Phoenix specifications and recommendations
The cabinet comes with a Phoenix plug (Type: SPC 5/4 Push-in
spring connector) which is already connected to the corresponding
Phoenix socket of the cabinet.
The plug allows for direct wire connection without any tools
depending on the cross section and conductor structure.
Technical specifications
Conductor cross section
Flexible, ferrule without plastic sleeve
Flexible, ferrule with plastic sleeve
Ferrule length (min/max) 10/15 mm
Release tool Flat-tip screwdriver 0.6 x 3.5 x 100 mm
up to 6 mm2 (AWG 9)
up to 4 mm2 (AWG 11)
Recommended connecting cable
d&b K3116.100 MC2 SWR
Ferrule without plastic sleeve (enclosed with the cabinet)
2 x 2.5 mm2 (AWG 13)
d&b LoadMatch
With the d&b four channel amplifier platform, the LoadMatch
function enables the amplifier to electrically compensate for the
properties of the loudspeaker cable used without the need for an
additional sense wire. For applicable loudspeakers, LoadMatch is
therefore independent of the connector type used.
d&b KSLi-SUB/KSLi-GSUB Manual 1.1 en - perliminary - 7
2.3 Operation
Amplifier output mode(s): 2-Way Active
Application Setup Cabinets per
pair of amplifier
channels
KSLi-SUB KSL-SUB
KSL-SUB AP
KSLi-GSUB KSL-SUB
KSL-SUB AP
1
1
1
1
AP setup
In connection with d&b ArrayProcessing (AP), the AP setup
contains the AP data that are generated in the ArrayCalc
simulation software and transferred to the applicable amplifiers via
the d&b Remote network using R1.
As soon as the data have been sent to the amplifiers, the AP setup
will be automatically activated.
2.3.1 Controller settings
For acoustic adjustment the INFRA mode can be selected.
KSLi-SUB frequency response, standard and INFRA mode
INFRA mode
With the INFRA mode selected, the frequency response of the
system extends from 33 Hz to 75 Hz.
The KSLi-SUB/KSLi-GSUB can now be used to supplement
applicable d&b loudspeaker systems operated in full range mode.
2.4 Technical specifications
System data
Frequency response (–5 dB standard)
Frequency response (–5 dB INFRA) 33 Hz - 75 Hz
Max. sound pressure (1 m, free field) with 40D 139 dB
(SPLmax: Broadband signal IEC 60268)
36 Hz - 105 Hz
Loudspeaker data
Nominal impedance front/rear
Power handling capacity front (RMS/peak 10 ms) 900/3500 W
Power handling capacity rear (RMS/peak 10 ms) 500/2000 W
Components 3 x 15" driver
Connections 1 x NLT4 F
Pin assignment
1+: Front+/1–: Front– /2+: Rear+/2–: Rear–
Phoenix option Phoenix socket (Type: DFK PC 4/4 GF)
Phoenix plug (Type: SPC 5/4)
Optional front splay (KSLi-SUB) 0° or 2°
Weight KSLi-SUB 82 kg (181 lb)
Weight KSLi-GSUB 78 kg (172 lb)
4/8 ohms
d&b KSLi-SUB/KSLi-GSUB Manual 1.1 en- perliminary -8
KSLi-SUB cabinet dimensions in mm [inch]*
*The same dimensions apply to the KSLi-GSUB
d&b KSLi-SUB/KSLi-GSUB Manual 1.1 en - perliminary - 9
3 Manufacturer's declarations
3.1 EU conformity of loudspeakers (CE symbol)
This declaration applies to:
d&b KSLi-SUB loudspeaker, Z0795
d&b KSLi-GSUB loudspeaker, Z0796
manufactured by d&b audiotechnik GmbH & Co. KG.
All production versions of these types are included, provided they
correspond to the original technical version and have not been
subject to any later design or electromechanical modifications.
We herewith declare that said products are in conformity with the
provisions of the respective EC directives including all applicable
amendments.
A detailed declaration is available on request and can be ordered
from d&b or downloaded from the d&b website at
www.dbaudio.com.
3.1.1 WEEE Declaration (Disposal)
Electrical and electronic equipment must be disposed of separately
from normal waste at the end of its operational lifetime.
Please dispose of this product according to the respective national
regulations or contractual agreements. If there are any further
questions concerning the disposal of this product, please contact
d&b audiotechnik.
d&b KSLi-SUB/KSLi-GSUB Manual 1.1 en- perliminary -10
- perliminary -
D2733.EN .01, 01/2020 © d&b audiotechnik GmbH & Co. KG
www.dbaudio.com
Loading...