d&b Z5397 User Manual

Page 1
Z5397
Z
Mounting instructions 1.2 en
Page 2
General information
Z5397 Mounting instructions
Version: 1.2 en, 05/2015, D2817.EN .01
Copyright © 2015 by d&b audiotechnik GmbH; all rights reserved.
Keep these mountings instructions with the product or in a safe place so that they are available for future reference.
When reselling this product, hand over these mounting instructions to the new customer.
d&b audiotechnik GmbH Eugen-Adolff-Strasse 134, D-71522 Backnang, Germany T +49-7191-9669-0, F +49-7191-95 00 00 docadmin@dbaudio.com, www.dbaudio.com
Page 3

Contents

1. Z5397 YP Swivel bracket............................................. 4
1.1. Scope of supply and weight................................................... 4
1.2. Safety precautions................................................................... 4
1.3. Intended use............................................................................ 5
1.4. Assembly.................................................................................. 5
1.5. Adjustments.............................................................................. 6
1.6. Built-in dimensions................................................................... 6
2. Declarations........................................................................ 8
2.1.
Manufacturer's declaration.................................................... 8
2.2. Disposal................................................................................... 8
d&b Z5397 Mounting instructions 1.2 en 3
Page 4

1. Z5397 YP Swivel bracket

1.1. Scope of supply and weight

Please verify the shipment for completeness and proper condition of the items.
Qty. d&b Code Description
1 Z5397 YP Swivel bracket
1 D2817.EN .01 Z5397 Mounting instructions
Weight 1.6 kg (3.5 lb)

1.2. Safety precautions

General safety
Installation and setup should only be carried out by qualified and authorized personnel observing the valid national Rules for the Prevention of Accidents (RPA).
It is the responsibility of the person installing the assembly to ensure that the suspension/fixing points are suitable for the intended use.
Always carry out a visual and functional inspection of the items before use. In case there is any doubt as to the proper functioning and safety of the items, these must be withdrawn from use immediately.
Operational safety
It is essential to secure the bracket with the securing pin [S] before lifting the cabinet or placing it onto a loudspeaker stand.
When using the bracket, all locking devices (securing pin [S] and fixing lever [F]) must be secured.
Do not under any circumstances unlock the securing pin [S] to adjust the vertical angle of the cabinet.
Secondary safeties must always be provided and used when flying or fixing loudspeaker loads overhead.
Load safety information
The Z5397 YP Swivel bracket is designed to support one YP loudspeaker (Y7P or Y10P).
No additional loads must be added.
The bracket must only be used in an upright position or suspended vertically as shown in the graphic opposite.
d&b Z5397 Mounting instructions 1.2 en4
Page 5

1.3. Intended use

The d&b Z5397 YP Swivel bracket must only be used in conjunction with d&b YP cabinets (Y7P or Y10P) as described in these mounting instructions.
Using the Z5024 Loudspeaker stand adapter, YP cabinets can be mounted onto a loudspeaker stand with a tube diameter of 35 mm (1.4").
Using the Z5010 TV spigot with fixing plate in conjunction with the Z5012 Pipe clamp, YP cabinets can be vertically flown from overhead bars or trusses with a tube diameter between 40 mm and 70 mm (1.5" and 2.75").
The horizontal aiming as well as the vertical aiming can be set continuously.

1.4. Assembly

Note: To ensure the cabinet to be exactly vertically aligned
within the bracket the d&b logo should always at the bottom left whether the cabinet will be mounted on a high stand or flown from bars or trusses.
1. Insert the hooks of the bracket's adapter plate into the corresponding slots of the cabinet's quick lock adapter plate.
2. Push the adapter plate towards the back of the cabinet until it is fixed in place.
3. Insert the securing pin [S] into the corresponding socket.
Ensure the securing pin is properly inserted and locked.
Þ
d&b Z5397 Mounting instructions 1.2 en 5
Page 6

1.5. Adjustments

Function of the fixing lever [F]
For adjustment of the cabinet and for visual reasons, it might be necessary to set the fixing lever to another position.
1. Pull the lever towards you.
2. Turn it to the desired position.
3. Release the lever to fix it in place.
Vertical aiming
1. Slightly loosen the fixing lever [F].
2. Set the loudspeaker to the required vertical angle.
3. Retighten the fixing lever.
Horizontal aiming
The horizontal aiming is set using the loudspeaker stand adapter or the TV spigot assembly.

1.6. Built-in dimensions

Z5397 YP Swivel bracket, Mounting options and built-in dimensions in mm [inch]
d&b Z5397 Mounting instructions 1.2 en6
Page 7
Built-in dimensions Z5010/Z5012 Assembly
Z5397 YP Swivel bracket dimensions in mm [inch]
d&b Z5397 Mounting instructions 1.2 en 7
Page 8

2. Declarations

2.1. Manufacturer's declaration

This declaration covers:
d&b Z5397, YP Swivel bracket.
National standards and technical specifications applied:
DIN 18 800, DIN 1055, BGV C1.
Backnang, 2014-05-26
Frank Bothe, Head of R&D d&b audiotechnik GmbH

2.2. Disposal

When out of use the rigging components must be disposed of in accordance with the national environmental regulations.
Ensure that damaged rigging components are disposed of in a way that they cannot be used again.
d&b Z5397 Mounting instructions 1.2 en8
Page 9
Page 10
D2817.EN .01, 05/2015 © d&b audiotechnik GmbH
www.dbaudio.com
Loading...