Z5351
E8 Horizontal bracket
Mounting instructions (1.1 EN)
Contents
1. Product description and scope of supply......................................................3
2. Intended use..........................................................................................................3
3. Safety precautions...............................................................................................4
4. Mounting options and coverage angles.......................................................4
5. Assembly................................................................................................................5
6. Maintenance and care.......................................................................................5
7. Disposal..................................................................................................................5
Manufacturer's declarations..................................................................................6
General Information
Z5351 E8 Horizontal bracket
Mounting instructions
Version 1.1 EN, 03/2015, D2979.EN .01
Copyright © 2015 d&b audiotechnik GmbH; all rights reserved.
Keep this manual with the product or in a safe place so that it is
available for future reference.
d&b audiotechnik GmbH
Eugen-Adolff-Strasse 134, D-71522 Backnang, Germany
Telephone +49-7191-9669-0, Fax +49-7191-95 00 00
E-mail: docadmin@dbaudio.com, Internet: www.dbaudio.com
Fig. 1:Z5351 E8 Horizontal bracket
115 [4.5"]
9 [0.35"]
230 [9"]
398 [15.7"]
92 [3.2"]
Z5351 E8 Horizontal bracket
1. Product description and scope of supply
The Z5351E8 Horizontal bracket enables E8 loudspeaker cabinets to be
mounted and set to different horizontal or vertical angles.
Scope of supply
Please verify the shipment for completeness and condition of the items.
Qty. d&b Code Description
1 Z5351
4
4
4
1 D2979.INT Mounting instructions
Weight and dimensions
Weight.............................................................................................................1.5 kg (3.3 lb)
E8 Horizontal bracket [1]
Hex head bolt M10 x 25 [2]
Spring washer [3]
U washer [4]
Fig. 2: Dimensions in mm [inch]
2. Intended use
The Z5351 E8 Horizontal bracket must only be used in conjunction with
the d&b E8 loudspeaker as described in these mounting instructions.
Installation and set up should only be carried out by qualified and
authorized personnel observing the valid national Rules for the
Prevention of Accidents (RPA).
It is the responsibility of the person installing the assembly to ensure that
the suspension/fixing points are suitable for the intended use.
The horizontal bracket can be:
– directly mounted to walls or ceilings.
– horizontally flown and mounted to bars and trusses with a tube
diameter of up to 50 mm (2") using the Z5010 TV spigot with
fixing plate and the Z5012 Pipe clamp.
Z5351 Mounting instructions (1.1 EN) Page 3 of 6
(a)
(b)
(c)
Fig. 3: Semi-circular slots and hole of the
65°
0°
15°
310 [12.2"]
268 [10.5"]
65°
0
°
15°
0°
30°
357 [14"]
300 [11.8"]
end of the bracket.
3. Safety precautions
General safety
Always carry out a visual and functional inspection of the bracket
before use. In case of any doubts the bracket must not be used. Please
also refer to section 6. Maintenance and care on page 5.
Load safety information
The maximum permitted working load of the bracket is 7.3 kg
(16.1 lb) (according to BGV C1) which corresponds to the weight of
one E8 loudspeaker.
4. Mounting options and coverage angles
Each end of the bracket (Fig. 3) is provided with two semi-circular slots
(a, b), 12 mm (0.47“) wide, marked with 5° and 15° detents and one
12 mm (0.47“) hole (c). Slot (a) allows angle settings over a range of
80° and slot (b) over a range of 30°.
In conjunction with the M10 threaded inserts at the top and bottom of
the loudspeaker cabinets the bracket can be attached differently. The
following mounting options and coverage angles are possible:
Option 1:
One bolt is fitted to the 12 mm hole (c) and a second to the semicircular slot (a) on each end of the bracket. The vertical coverage angle
can be set over a range of 80° (65° or 15° relative to the main axis of
the loudspeaker (0°) - Fig. 4). The angle can be read from the point on
the scale which corresponds to the center of the fixing bolt in slot (a).
Fig. 4: Option 1
Option 2:
Both bolts are fitted to the semi-circular slot (b) on each end of the
bracket. The vertical coverage angle can be set over a range of 30°
(Fig. 5). The angle can be read from the point on the scale that
corresponds to the center of the fixing screw in slot (b) which is fitted
along the scale.
Fig. 5: Option 2
Z5351 Mounting instructions (1.1 EN) Page 4 of 6
Fig. 6: Tie bar of the bracket
5. Assembly
Fixing to walls or ceilings
Two mounting holes 9 mm (0.35“) are provided on the back of the
bracket for fixing the bracket directly to walls or ceilings or other
suitable surfaces.
Attaching the bracket to the cabinet
NOTICE: Only use the supplied and specified screws [2]. Always use
the spring washer [3] and U-washer [4] to prevent the bolts from
slackening.
Tools required: Open ended spanner/wrench (size #17).
1. Fit the cabinet to the prepared bracket.
2. Bolt the bracket to the cabinet.
3. Set the desired angle before finally tightening the screws.
6. Maintenance and care
In case of mobile use of the bracket please observe the following notes.
Storing/Transport
Due to its surface treatment the bracket is temporarily protected against
moisture. However, ensure the bracket is in a dry state while stored or
during transport and use.
During transport ensure the bracket is not stressed or damaged by
mechanical forces.
Cleaning
Regularly clean and lubricate the bracket using WD-40®or a similar
product.
Inspections
To eliminate the potential risk of accident due to malfunctioning of the
bracket carry out a visual and functional inspection of the bracket
regularly. In particular pay attention to obvious damage (deformation,
cracks and corrosion).
If the bracket fails to operate correctly and/or safely the bracket must
be withdrawn from use immediately.
7. Disposal
Please dispose of this product according to the respective national
regulations.
Ensure that damaged rigging components are disposed of in a way that
they can not be used again.
Z5351 Mounting instructions (1.1 EN) Page 5 of 6
Manufacturer's declarations
EC Declaration of conformity
within the meaning of the EC Machine Directive 98/37/EEC
We hereby declare that the equipment designated below is designed and built in the version sold by us in such a way as
to comply with the relevant fundamental safety and health criteria of the applicable EC Directive(s). This declaration shall
cease to be valid if alterations are made to the equipment without our prior agreement.
This declarations covers:
d&b E8 Horizontal bracket, Z5351
To be used as described in these mounting instructions.
National standards and technical specifications applied:
DIN EN ISO 12100, DIN EN 1050, BGV C1
D2979.EN .01, 03/2015 d&b audiotechnik GmbH
Backnang, 2008-01-10
(Frank Bothe, Managing director)
d&b audiotechnik GmbH, Eugen-Adolff-Str. 134, D-71522 Backnang, Germany, Phone +49-7191-9669-0, Fax +49-7191-95 00 00
Loading...