DaytonAudio PMA250 User Manual

250W PA MODULE
with MIXER

Model: PMA250 User Manual

Thank you for purchasing the PMA250 PA Amplifi er. This amp is ideal for building active monitors or converting existing speakers to a
powered audio system. Perfect for karaoke applications! The open frame module design mounts easily to speaker cabinets, creating a
self contained portable P.A. system. The unit features two microphone and one line level input, each with its own level control that offers
easy mixing of all inputs. Each input is compatible with both balanced and unbalanced sources. A handy balanced line level output
allows easy daisy chaining of multiple amplifi er units. The PMA250 also has a convenient speaker output for connection of an additional
slave or non-amplifi ed speaker system. Other useful features include bass, treble, and master volume controls.

Inputs/Outputs

MIC 1 & 2: Allows the connection of both balanced (XLR) and unbalanced (1/4")

Note: Not to be used as an input for line level equipment e.g. CD

Line In: Allows the connection of both balanced (XLR) and unbalanced (1/4") line

Note: If you are using a turntable with this unit, a RIAA equalized

Line Out: Balanced (XLR male) line level output for easy daisy chaining of multiple

Speaker Out: Allows the connection of an additional slave or non-amplifi ed speaker

Note: The absolute minimum impedance for this amplifi er is 4 ohms.

Power In: This unit features a grounded IEC power jack. This jack allows the user to

microphones. Each MIC input has a level control to independently adjust
or mix each input.

players, tuners, turntables, etc.

level equipment e.g. CD players, tuners, cassette players, etc. It features
a level control to independently adjust or mix the input level. A 1/4" plug
to two RCA jack adaptor is included for easy connection of devices using
RCA type output connectors. This is a mono input. All stereo signals are
summed to mono.

phono preamp must be used.

units. The Line Out signal will include any MIC or Line In input being used.
This Line Out should be connected to the Line In of additional units.

system. The connection uses a standard 1/4" plug with the tip being positive.
The minimum impedance allowed for the slave speaker is 8 ohms.

If the active speaker impedance is 4 ohms, the Speaker Out feature
should not be used. Example: Active speaker = 8 ohms, slave speaker
= 8 ohms, total amplifi er load will be 4 ohms which is acceptable.
Active speaker = 4 ohms, slave speaker = 4 ohms, total amplifi er load
will be 2 ohms which is not acceptable and could cause damage to
the amplifi er.

quickly exchange the power cord if damaged or if a longer cord is desired.
This IEC jack also houses the main power fuse (5A, 110V/2.5A, 230V
GMA). If the unit stops operating for any reason, always check this fuse
fi rst. An extra fuse is located inside the fuse housing.

Master: Controls the volume or output level of the amplifi er.

Treble: Allows the user to fi ne tune the high frequency output of the amplifi er. The

Bass: Allows the user to fi ne tune the low frequency output of the amplifi er. The

Clip LED: The unit features a red Clip LED indicator. If the Clip LED is illuminated

Power: This switch turns on and off the amplifi er. The unit features a green power

is present.

Voltage: This switch allows the user to select between 115VAC or 230 VAC.

Specifi cations

Output Power: 150 watts into 8 ohms @ 0.09% THD (1 kHz)

250 watts into 4 ohms @ 0.9% THD (1 kHz)

Freq. Response: MIC 1 & 2: 20 Hz-15 kHz (+/-3 dB)
Line In: 10 Hz-18 kHz (+/- 3 dB)
Input Sensitivity: MIC 1 & 2: 5mV
Line In: 500mV
Voltage Input: 110~120 VAC, 60 Hz, 450 watts

220~230 VAC, 50 Hz, 450 watts

Dimensions: 10-7/16" W x 10-7/16" H x 3-5/16" D
Enclosure Cutout: 9-1/4" W x 9-1/2" H
Weight: 12 lbs.

Controls/ Switches

frequency is centered at 10 kHz and allows for +/- 12 dB of adjustment.

frequency is centered at 100 Hz and allows for +/- 12 dB of adjustment.

or fl ashing, the amplifi er is producing distortion (clipping) and the volume
level should be reduced.

LED for positive indication that AC power

Dayton Audio products are warranted free from defects in material and workmanship for 5
years from date of purchase. 1 year warranty applies to the following products: powered
subwoofers and electronic devices (e.g. subwoofer amplifi ers, and plate amplifi ers, as well
as the Omnimic V2 and DATS loudspeaker testing devices). In the rare case of a product
failure, please contact your place of purchase or call our Customer Support Department at
[phone].

There are no other warranties, either expressed or implied, that extend the foregoing, and
there are no warranties of merchantability or fi tness for any particular purpose. Dayton Audio
is not responsible for any consequential or inconsequential damage to any other unit or
component or the cost for installation or extraction of any component of the audio system,
or for the improper use of products. This includes but is not limited to burnt voice coils,
overheating, bent frames, holes in the cone, or broken lead wires.

This warranty gives you specifi c legal rights and you may also have other rights that vary
from state to state.

Non-Warranty Service: If non-warranty service is required, the product may be sent to
the Company for repair/replacement, transportation prepaid, by calling [phone] for
details, complete instructions, and service fee charges.

Warranty Information

Warranty Limitations

Dayton Audio® Last Revised: 5/18/2015

daytonaudio.com

tel + 937.743.8248
[e-mail]

705 Pleasant Valley Dr.
Springboro, OH 45066
USA