Page 1
200W INTEGRATED
STEREO HYBRID
TUBE AMPLIFIER
Model: HTA200
User Manual
Page 2
Safety Information
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of electric shock, do not remove cover.
No user serviceable parts inside. Refer servicing to qualied
personnel. To reduce the risk of re and shock do not expose
unit to rain or moisture. The unit should be connected to an
earth grounded AC electrical socket. The unit should be operated in a well ventilated area. Minimum clearance is 2 inches
from the ventilation openings.
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(a)This device may not cause harmful interference.
(b)This device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
2
Page 3
Welcome
Thank you for purchasing the Dayton Audio HTA200 Integrated Stereo Hybrid Tube Amplier.
designed to make it easy for anyone to enjoy the warm, natural sound quality of vacuum tube amplication without the
size, power consumption, and price of using traditional tube ampliers. The HTA series from Dayton Audio achieves
this by combining vacuum tubes in th
output power amplier. Additionally, each amplier includes multiple analog and digital inputs for connecting modern
devices such as computers with the classic sound of tube ampliers.
e preamp input section with a modern power efcient solid state Class A/B
This amplier has been
Contents
Useful Features................................................................................................................................................................3
What's In the Box ............................................................................................................................................................3
Controls and Functions
Front Panel..................................................................................................................................................................4
Rear Panel..................................................................................................................................................................5
Remote Control...........................................................................................................................................................6
Connections
Connecting Power ......................................................................................................................................................6
Connecting Speakers.................................................................................................................................................7
Connecting Banana Plug Cables...............................................................................................................................7
Connecting Speaker Wires.........................................................................................................................................7
Connecting A Subwoofer............................................................................................................................................7
Connecting Headphones............................................................................................................................................7
Connecting Sources...................................................................................................................................................8
Troubleshooting..............................................................................................................................................................9
Specications ................................................................................................................................................................10
Warranty .........................................................................................................................................................................10
Useful Features
• Phono preamp for connecting turntables without any extra hardware
• Built-in high-quality USB-DAC for direct connection to any computer
• Warm glow from the preamp tubes and front panel controls
• Control the tone with bass and treble knobs
• Remote control and motorized volume knob for easy operation from across the room
• Easily add a subwoofer with the dedicated subwoofer output
What's In The Box
• HTA200 Integrated Stereo Hybrid Tube Amplier
• Remote Control
• AC Power Cable
• Bluetooth Antenna
• User Manual
*Please check to make sure that nothing is missing from the package
3
Page 4
Controls and Functions
Front Panel
1. POWER SWITCH/INDICA T OR
Turns the device on and off.
2. POWER INDICA T OR
The ring surrounding the power switch will
illuminate amber when the unit is turned on.
3. METERS
Indicates the audio output level of the left and
right channels.
4. DISPLAY
Indicates the input source.
............. Aux
.......... Bluetooth
......... Coaxial
............. Optical
............. Phono
5. BASS CONTROL
Adjusts the volume level for the bass output.
6. TREBLE CONTROL
Adjusts the volume level for the treble output.
7. HEADPHONE OUTPUT
The headphone output allows you to listen to any
input privately without playing audio through your
speakers. The output accepts ¼” TRS headphone
connectors. Plugging in headphones here will cut off
the signal to the speakers and SW OUT [11].
NOTE: To avoid accidental damage to your headphones or speakers always turn down the volume
before connecting or disconnecting headphones.
8. VOLUME CONTROL
Turn this up to begin experiencing the warm natural
tone generated by the tube preamplier.
9. SOURCE INPUT SELECTOR
Press the corresponding input button to select the
desired source.
NOTE: PC-USB input will not be selectable
unless there is a device connected to the unit
and powered on.
................... PC-USB
........... Mute
4
Page 5
Rear Panel
10. DIGITAL (OPTICAL) INPUT
11. SUBWOOFER OUTPUT
Use a single RCA cable to connect the SW OUT
to a powered subwoofer or separate subwoofer
amplier.
This will output a full range mono signal and the
volume output will change depending on the position
of the front panel volume control.
NOTE: The output will signal will be interrupted
when headphones are connected on the front of the
amplier.
12. BLUETOOTH ANTENNA
Connect the supplied Bluetooth antenna here for
optimum signal strength.
13. GROUND TERMINAL
14. AC VOLTAGE SELECTOR SWITCH
The unit is set at the factory for 110V operation. For
220V operation, move the voltage selector switch
to the 220V position. When operating at 220V the
internal fuse located in the IEC socket should also
be changed. In most 220V applications a separate
power cord will be required and is not included.
15. PC-USB INPUT
16. DIGITAL (COAXIAL) INPUT
17. LINE LEVEL (AUX) INPUT
18. PHONO INPUT
19. SPEAKER OUTPUTS
Using insulated 2 conductor wire to connect to
speakers. The polarity, positive (+), and negative (-)
for all speaker and amplier connections must be
consistent so both the left and right speakers are
in phase.
NOTE: The speaker outputs are not bridgeable.
20. AC POWER INPUT
5
Page 6
Remote Control
1. MUTE
1. When muted, the HT A200 will display ---- on it’ s screen.
2. VOLUME +/-
1. Control the volume of the amplier. The volume knob will
rotate to indicate the current level of the amplier.
3. TRACK TRANSPORT CONTROLS
1. Control the playback of the Bluetooth input.
2. “play/pause logo” – start/pause the current song.
3. “forward logo” – skip forward to the next song.
4. “backward logo” skip backward to the beginning of the current
song or the previous song.
4. INPUT SELECTION
1. Directly select any of the inputs here.
2. NOTE: PC-USB is only selectable when a device is connected
to the USB port on the rear of the unit.
Connections
Connecting the Power Cable
Before connecting the main power cable, make sure that the voltage selector switch is set according to your local
voltage. Incorrect setting of the voltage selector switch could cause damage to the amplier and has a potential risk
of re.
6
Page 7
Connecting Speakers
The amplier can power speakers with a minimum impedance of 4Ω. Using high quality two conductor speaker wire
connect your speakers to the binding posts on the rear of the unit.
Connect the HT A200’ s left speaker terminals marked “L-” and “L+” to the corresponding “-” and “+” terminals on your
left speaker. Repeat the same process for the right channel.
Note: Never connect the negative terminals together or to ground. The HTA200 is not designed to operate in a
bridged mode and attempting to do so may damage the amplier.
Connecting Banana Plug Cables
1. Tighten the knob.
2. Insert the banana plug terminated cable into the
end of the corresponding terminal.
Connecting Speaker Wires
1. Strip about 3/8" of insulation from the end of each
speaker wire and twist the bare wires of the cable
together.
2. Unscrew the knob before inserting the bare wire into
the hole in the side of each terminal before tightening
the knob to secure the wire.
Connecting A Subwoofer
If you really want to feel the bass or just want to bother the neighbors you can add a subwoofer using the SW OUT
connection on the rear of the HT A200. This signal is full range and will send a mono summed signal that is controllable by the front volume knob. Using a single RCA cable you can connect to the line level input on a powered sub-
woofer or to any external subwoofer amplier to power passive subwoofers.
Connecting Headphones
Headphones can be connected to the ¼" TRS connection on the front of the HTA200. This is great for listening to any
source and enjoying the classic warmth from the tube preamps. Plugging in headphones will stop any signal from
being output to the speaker output terminals or SW OUT.
Note: To avoid damage to headphones or your hearing make sure to turn down the volume before plugging in your
headphones. Always turn down the volume knob before unplugging headphones to avoid accidental output to your
speakers or startling any cats napping nearby .
7
Page 8
Connecting Sources
TV
PC
CD PLAYER
The HT A200 is capable of receiving signals directly from a wide variety of sources. Using high quality cables will
ensure the best possible transmission from your connected devices.
WBA51
TURNTABLE
Connecting a Turntable
The HTA200 is capable of connecting directly to most turntables without the addition of an external phono preamplier.
1. Ensure that your turntable is set to output a phono signal. Many modern turntables have the ability to output
either a line level signal or a phono signal. If your turntable is set to output a line level signal please connect it
to the AUX input on the HTA200.
2. Remove the covers from the PHONO RCA plugs and connect the turntable to the phono input.
3. Connect the ground wire of the turntable to the ground terminal on the rear of the HT A200 (if applicable).
Bluetooth as a Source
1. Connect the Bluetooth antenna to the BT ANTENNA port on the rear of the unit. Also make sure that the
Bluetooth input is selected on the HT A200.
2. Using a smart phone, tablet, computer, or other device capable of transmitting Bluetooth audio, go the
devices settings and scan for available Bluetooth devices.
3. Look for and select “HT A200” in the device list and begin pairing. The front display panel on the HTA200 will
ash until a device is paired.
4. Once the front display panel stops ashing and your device indicates that you are connected you can begin
streaming your favorite music from up to 30 feet away .
8
Page 9
Troubleshooting
9
Page 10
Specications
Maximum Power Output (Peak)................. 140W x 2 @ 4 Ohm
RMS Power Output..................................... 70W x 2 @ 4 Ohm
Total Gain .................................................... 29 dB
THD+N ......................................................... <1.5% @ Maximum Rated Output
Frequency Response................................. 15 Hz – 20,000 Hz (1 dB)
Input Sensitivity.......................................... 630 mV
Channel Separation.................................... 53 dB
Minimum Speaker Impedance................... 4 Ohm
Tone Controls – Bass/Treble..................... 6 dB/oct @ 200 Hz and 4,000 Hz
Signal To Noise Ratio................................. 80 dB
Digital Section
Digital Inputs............................................... SPDIF LPCM (up to 48 kHz 16 Bit)
PC-USB........................................................ up to 192 kHz 32 Bit
Bluetooth..................................................... 5.0
General
Power Requirement
USA....................................................110V, 60 Hz
EC...................................................... 220V, 50 Hz
Standby Power Consumption ................... 45W
Preamplier Tubes ..................................... 13P1P x 2, 6H2 x 2, 6A2 x 2
Stabilivolt Tube........................................... WY3P
Amplication............................................... Class A/B
Dimensions (W, H, D)................................. 13-1/8 x 6-1/2 x 12-1/2 in. (333 x 165 x 318 mm)
Weight.......................................................... 16.4 lbs. / 7.44 kg
All Specications are accurate at the time of printing.
Dayton audio reserved the right to make improvements without notice.
Warranty
Dayton Audio products are warranted to be free of all defects in material and workmanship for 5 YEARS from the
date of purchase from an authorized Dayton Audio dealer. This warranty and all rights provided are limited to the
original owner and are non-transferable. Responsibility is limited to replacement or repair as set forth in this warranty
statement.
Should a product require warranty service during this period, Dayton Audio will repair or replace without charge, any
part or product proving defective in material or workmanship. All warranty repairs and service must be performed by
an authorized Dayton Audio technician or service facility. The use of non-authorized repair services renders this war
ranty null and void, and any charges relating to non-authorized repair are the responsibility of the product owner.
All expenses (except return shipping costs) related to replacing or repairing a defective part or product under this
warranty shall be assumed by Dayton Audio. Dayton Audio reserves the right to replace defective product with a new
or factory reconditioned unit.
For more information and to register your new Dayton Audio device visit daytonaudio.com.
-
10
Page 11
Notes
Purchased on: ____________________
11
Page 12
5-Year Limited Warranty
See daytonaudio.com for details
Dayton Audio
daytonaudio.com
tel + 937.743.8248
info@daytonaudio.com
®
705 Pleasant Valley Dr.
Springboro, OH 45066
USA
Last Revised: 2/22/2023
12
Loading...