Daystar KU70033BK User Manual

TOOLS NEEDED

BILL OF MATERIALS

• Floor jack

• Jack stand (s) 4

• Wheel chock

• Grease ( poly lube gun KU11005)

• 3/4 drive ratchet

• 10” 3/4 extension

• 5/8 wrench and 5/8 socket

• Measuring tap

• 18mm wrench

• 18mm socket

Jeep JK Products

• KJ09138 3/4” Front & rear lift

• KJ09137 1 3/4” Front & rear lift

• KU09059 EVS Foam bump-stops

• KU09060 EVS Foam bump-stops

• KU70034 Ft lower control arms

• KU70033 Rear upper control arms

• KU70037 Rear lower control arms

• KU70091 poly flex tool

• KU11005 Poly lube gun

• KJ71020 Upper dash panel

• KJ71020 Lower switch panel

Part # Description Qty
S11098
S11117

BU70033
M03856
S11118
S10205
S10212
S10818
S10903
S10818
P11183
S11123

Upper arm 2

Rod end 2

Hardware kit 1

Bushing 8

Sleeve 2

9/16 Nut 2

9/16 Bolt 4

1-14 Jam nut 2

washer 8

1-14 Jam nut 2

Thread lock 1

Nut plate 2

KU70033 Rear upper

2007 to Current Jeep JK control arm kit

Hells gate, Moab UT

www.Daystarproducts.com

Tech Support Contact Info

[e-mail]

Phone: [phone]

Fax: [phone]

841 South 71

st

Avenue

Instruction Sheet P11241
2007 Daystar Products International Inc.

Thank you for choosing Daystar Products

Daystar recommends a certified technician install this system. In addition to
these instruction, professional knowledge of disassemble/reassembly proce­dures as well as post instructions checks must be known. Attempts to install
this system without this knowledge and expertise may jeopardize the integrity
and/or operating of the vehicle.

Please read all the instructions before beginning the installation. Check the kit
hardware against the parts list. Be sure you have all the needed parts and un­derstand where they go. If anything is missing , do not proceed with the in­stallation, call Daystar Products to obtain needed items

.

12.

With the Daystar control arm installed tighten the mount bolts to 75 ft
pounds and jam nuts.

Product Use Information

As a general rule, the taller a vehicle is the easier it will roll. We strongly rec­ommend , because of rollover possibility, that seat belts and shoulder harness
be worn at all times. Avoid situations where a side rollover may occur.

Braking performance and capabilities are decreased when significantly large/
heavier tires and wheels are used. Take this into consideration while driving,
Also , speedometer recalibration is necessary when larger tires are installed.

Do not add, alter, or fabricate any factory or after-market parts which increases
vehicle height over the intended height of the Daystar Product purchased. Mix­ing component brands, lifts, and/or combining body lift with suspension lift
voids all warranties. Daystar makes no claims regarding lifting devices and
excludes any and all implied claims. We will not be responsible for any prod­ucts that is altered.

Notice to Dealer and Vehicle Owner

Any vehicle equipped with any Daystar Product must have the “Warning to
driver” decal installed on the sun visor or dash. The decal is to act a constant
reminder for whoever is operating the vehicle of its unique handling charac­teristics. INSTALLING DEALER— Its is your responsibility to install the
warning decal and forward these instructions on too the vehicle owner for
review and to be kept in the vehicle for service life.

After installation occurs, a qualified alignment facility is required to align the
vehicle to factory specs.

Reinstall the wheel and jack up the jeep and remove the jack stands.

13.

Repeat steps 6 to 13 on the other side.

14.

Check that all hardware and lug nuts are tighten.

15.

Using a lube gun lube the bushings.( KU11005 )

16.

You should have your alignment checked.

17.

Check all hardware after 500 miles.

18.