
KT09112 1996-2001 4-Runner 2WD & 4WD
1 ½” Front Coil Spring Spacer Lift Kit With Rear Coil Spring Spacers
www.DaystarWeb.com
Tech Support Contact Info
Tech@DaystarWeb.com
Phone: 623.907.0081
Fax: 623.907.0088
841 South 71st Avenue
Phoenix, AZ 85043
Part No. Description Qty.
M00337 Boot Shock/Strut 4
M02233 End Link Bushings 4
M03112 Bump stop 4
M03272 Coil Spring Spacer 2
Bill of Materials
P10027 Grease Pack 2
P01055 Cable Ties 4
M03277 Coil Spring Spacers 2
S10762 M10-1.25X 50mm Stud 6
S10518 10mm Nylock Nut 6
INSTALLATION INSTRUCTIONS
FRONT
1. Read complete instructions before beginning installation, the following special tools are recommended: Coil spring
compressor, floor jack, ball joint separator, jack stands, and metric hand tools.
2. Jack the vehicle in the center of the front cross member.
3. Support the vehicle by placing jack stands on the frame cross member so that the front tire/wheels are off the
ground.
4. Remove the front tires/wheels.
5. Disconnect the sway bar end links and remove the upper ball joint cotter pin and nut.
6. Separate the upper ball joint from the spindle. (Using ball joint separator or a suitable tool)
7. Remove upper strut nuts on the strut tower (3) on each side of vehicle that holds strut assembly to the frame
mount.
8. Remove the lower strut bolt from the lower control arm and remove the strut assembly from the vehicle. (Note the
direction of the bolt for reinstallation)
9. Compress the coil spring on the strut assembly with a suitable coil spring compressor and remove the upper strut
isolator mount nut.
10. Remove the compressed coil spring assembly from the strut and install the strut boot.
11. Remove the coil spring isolator from the strut mounting plate.
12. Remove the 3 pressed in studs on the upper strut isolator mount and install the supplied 10mm bolts without nuts.
13. Reinstall the coil spring isolator to the upper strut mounting plate.
14. Reinstall the compressed coil spring onto the strut assembly and re-attach the upper strut mount plate using the
new strut stem cushions and stock hardware.
15. Decompress the coil spring in the strut assembly. Make sure that the spring is seated correctly into the strut
assembly alignment indentation.
16. Slide the coil spring spacer onto the strut assembly over the 10mm bolts.
17. Install the strut assembly into the strut tower and start the upper three 10mm nuts with spring washers. (Make
sure that the bottom of the strut is aligned as well)
18. Install the lower strut bolt in the original position that it was removed. (Step 8)
19. Using the floor jack, raise the lower control arm and connect the upper ball joint on the upper control arm to the
spindle. Make sure that you replace the cotter pin. (Not supplied)
20. Install the front tires/wheels.
21. Lower the vehicle onto the ground and tighten the upper strut tower nuts. (3 on each side)
22. Torque all bolts to factory specifications. Re-torq ue all bolts after 500 miles.
Instruction Sheet Page 1 of 2
P10513 Rev03
© 2006 Daystar Products
International Inc.

Tech Support Contact Info
Tech@DaystarWeb.com
KT09112
1 ½” Front Coil Spring Spacer Lift Kit With Rear Coil Spring Spacers
1. Jack up rear end and place jack stands under frame allowing re ar suspension to move up and down freely.
2. Disconnect lower shock mount bolts/nuts so that the rear axle droops and the coil springs become loose.
3. Disconnect the panhard bar at the drivers side of the axle.
4. Remove the coil spring and the coil spring isolator/bump-stop.
5. Place the isolator/bump-stop into the new coil spring spacer and then onto the frame. Reinstall the coil
6. Jack up the rear suspension so that the coil spring seats into the coil spring spacer and on the axle pad.
7. Jack up the rear of the vehicle, remove the jack stands and lower the vehicle. Check all bolts/nuts for
1996-2001 4-Runner 2WD & 4WD
INSTALLATION INSTRUCTIONS
REAR
spring in between the coil spring spacer and the axle. (Note: you may have to pry the coil spring onto the
axle pad.)
Reconnect the lower shocks mount bolts/nuts and reconnect the panhard bar.
tightness and recheck after 500 miles.
© 2006 Daystar Products
Instruction Sheet Page 2 of 2
P10513 Rev03
International Inc.
www.DaystarWeb.com
Phone. 623.907.0081
Fax. 623.907.0088
841 South 71st Avenue
Phoenix, AZ 85043