Daystar KJ71043BK User Manual

1

KJ71043BK

KJ71044BK ( Includes Switches)

2007-2010 JEEP WRANGLER JK

A Pillar Switch Panel

www.Daystarweb.com

Tech Support Contact Info

[e-mail]

Phone: [phone]

Instruction Sheet: P21095-02
2013 Daystar Products Interna­tional Inc.

Revision: 2
Revision Date: 09/04/2013
Revised by: TY

2

Introduction

is your number one source for Made In The USA

quality, Comfort Ride™ leveling kits. Now backed

with our exclusive Go Everywhere © Lifetime Lim­ited Warranty (see terms at Daystarweb.com). To assure your safety and prop­er installation of this product, take a moment to read all instructions and Prod­uct Safety Information before trying to install your Daystar® product. Current
OEM suspension design is complex: meaning safe and proper installation
requires understanding OEM service techniques for disassembly and assembly
of the components indicated together with the instructions and warnings set
out below and in the OEM service manual and your owner’s manual. Day-

star® strongly recommends seeking advice from or having this product in­stalled by a professional mechanic who can inspect your suspension, confirm
compatibility with your tire and wheel choice and, if needed, reset alignment
to optimize your steering and the features of your Daystar® Comfort Ride kit.

We are here to help if you have remaining technical questions after reading

Product Safety Information

Throughout these instructions important safety information is generally pre­ceded by one of three signal words indicating the relative risk of injury. The
signal words mean:

! WARNING A hazardous situation which, if not avoided, could result in
death or serious injury. You can be Killed or Seriously Hurt if you don’t fol­low instructions.

! CAUTION A hazardous situation which, if not avoided, could result in
minor or moderate injury. You can be moderately HURT and also may suffer
property damage if you don’t follow instructions.

NOTICE Careful attention is required to this instruction or operation but
does generally not relate to personal injury. Damage to your product or other
property may result if you don’t follow instructions.

!WARNING

Familiarize yourself with all vehicle manufactures’ and Daystar
warnings, instructions and limited warranties before driving your
modified vehicle. Also be aware many states / countries have
laws governing on-road vehicle modifications. You are responsi­ble for assuring the safety and legality of your vehicle. A sum­mary of current state vehicle laws is available at www.sema.org.

3

Quantity Description

1 Gloves

1 Razor Blade or Ezacto Blade

1 T-20 Torx Bit Driver

1 File

Tools Needed

Quantity Part Number Description

1 KJ71043BK or

KJ71044BK w/

switches

Windshield pillar
Switch panel

(Part List)

Bill of Materials

Installation Instructions

!Warning: Always work with appropriate personal safety
gear including safety glasses, gloves and hearing protection if
using air powered tools.

Begin by inspecting the components & hardware for dam­age. Then compare components & hardware to the bill of materi­als for completeness. If anything is missing/damaged, do not pro­ceed with the installation. Please, call Daystar Products (800-595-

7659) and we will send you the missing of damaged components

4

1. Remove the driver side sun visor using a t-20 Torx bit.

2. Unclip and remove the upper interior windshield roof trim
Molding.

3. Unclip and pull out gently to remove driver side interior
Windshield pillar trim panel.

4. Remove clips on back of factory part, using pliers.
NOTE check positioning of clips for reinstall, be gentle
Not to damage clips.

5. Transfer the clips on to back of the Daystar Switch Pillar
Trim panel. Support panel and gently push clips on to studs.

6. Your new Switch panel can accommodate up to 4 switches.

7. Working from the back of trim panel you can cut holes for
switches using a razor blade knife or ezacto knife. Cut small
and file hole for a snug fit.

8. Wire per instructions on items switches will power.

9. Install new Switch trim panel align clips with holes and push
in till panel clips in place.