Falcon
User Manual
About Daymak
Daymak is one of Canada’s largest Alternative Vehicle providers. We design, engineer, manufacture, import and repair everything from recreational dirt bikes, go-karts and electric
golf cars to alternative transportation solutions such as e-bikes and gas scooters.
Our electric bicycles represent an energy-e cient and eco-friendly alternative for people
who need to get around the city. They greatly increase the practicality of bicycle transportation in urban centres. Costing only a few cents to charge, an e-bike can make city life
more convenient and much less expensive.
While there are many new Green technologies that are still in their infancy, electric bicycles
have been developing over the last 40 years or more. E-bike technology has been dramatically re ned since the introduction of the rst custom-conversion bicycles. Today, electric
bicycles are a supremely reliable and a ordable means of transportation.
Daymak is constantly developing new eco-friendly alternative transportation strategies,
led by its own Research and Development department in Toronto, Canada. We are always
improving our products. Our innovative in-house engineering and quality testing provide
customers with many new kinds of reliable, eco-friendly vehicles, designed to help change
the lives of our customers and the world.
Daymak warranties, services, and stocks parts for everything it sells. We support our products.
Please feel free to visit our website. You’ll nd the latest in cool transportation solutions,
support for the products you’ve purchased and contact information.
Table of Contents
Introduction......................................................................................................................................................4
Part Diagrams ..................................................................................................................................................5
Product Speci cations ..................................................................................................................................6
Components.....................................................................................................................................................7
Operating Instructions ...............................................................................................................................10
Operational Conditions and Maintenance ..........................................................................................11
Parts Replacement Schedule....................................................................................................................12
Annex 1 ............................................................................................................................................................13
Introduction
E-Bikes
Riding an electric bicycle is a great way to hop around town conveniently and cheaply. EBikes represent a natural progression in the development of urban transportation.
Using only small amounts of electricity, e-bikes have the potential to radically reduce the
amount of pollution in our cities. As well, they are very quiet, so they do not add to the high
levels of noise pollution which we often take for granted. They are easy, and usually free,
to park. They are unobtrusive and highly practical additions to the urban landscape.
E-bikes are also inexpensive. They (currently) require no registration, no insurance, no licence and do not incur parking charges. As well, compared to internal combustion engines, the engines in electric vehicles have fewer moving parts and require far less maintenance.
Your Daymak e-bike is the result of Daymak’s years of experience, the highly trained technical skills of our sta and careful, ongoing design work by our engineers. We hope you
enjoy using this product and welcome any feedback that you may have.
New Laws
Most provinces in Canada, most states in the U.S.A, the United Kingdom and many European countries have new laws that permit cyclists to use electric motors to assist the regular operation of bicycles. Please check with your provincial or state government to learn
about your local laws. At the back of this manual you will nd the some of the common
Canadian provincial regulations that govern e-bikes.
Liability
Daymak does not assume any liability for damages, loss of pro ts, or claims from third
parties due to improper use of this product. Daymak does not assume any liability for damages due to problems with the product resulting from service by a third party that is not
certi ed by Daymak.
The information in this guide may be subject to change without notice. For the latest information available, please contact your local Daymak dealer or visit our website.
We have taken all possible measures to ensure the accuracy and completeness of the information in this guide. However, if you do nd anything missing, incomplete or wrong, do
not hesitate to contact us.
4
Part Diagrams
Diagram 1: The Falcon
This diagram illustrates the various parts of your Falcon. Please note that many of these parts are not user-serviceable and should be repaired only by trained professionals. This is especially true of the electrical
systems and the mechanical components.
1
1. Handlebars
2. Display panel
3. Wheel Guards
3
4
2
6
5
3
4
4. Wheels
5. Foot Pads
6. Battery
5
Product Specifi cations
Max Speed 20 km/h
Battery Lithium Battery
Range (from full charge) 55 km
Minimum Turning Radius Zero (turns on the spot)
Optimum Tire Pressure 1.0Bar/100kPa/15psi
Vehicle Weight 55 kg
Vehicle Footprint 65 x 49 cm
Chassis Height 10.0 cm
Handlebar Height 90 ~120 cm (adjustable)
Tire Diameter 50.5 cm
Maximum Carrying Capacity 120 kg
Minimum Carrying Capacity 30 kg
Maximum Climbing Gradient 26
6
Components
Handlebar
The handlebar maintains balance and controls the direction of the vehicle. The front and
rear of the handlebar is shown below. The height of the handlebar can be adjusted to suit
the rider:
Warning
The handlebars cannot tilt in excess of 45 left or right around the axis point.
7
Warning
To avoid injury, always hold the handlebar rmly during power-up, while riding or when
shutting the power o .
Display Panel
The display panel shows information about the Falcon’s operations. Make sure to install
both batteries - the battery indicator(s) should both turn on when installed correctly. The
speedometer can display current speed and track accumulated mileage. Display lights indicate whether the Falcon is on high speed or low speed. The battery indicator consists of
6 lamp lights, all of which gradually turn o as the battery is drained. If only a single lamp
light on the battery indicator is lit, it is a good idea to charge the battery.
Warning
In the event that the battery runs out of charge, the rider must shut o the power, and
charge the batteries immediately. Continued use of the vehicle may become hazardous
due to insu cient power.
Wheel Guards
The wheel guards prevent dirt splashing the rider, the foot mats and display panel protect
the rider from the rotating wheels while riding. If desired, the height of the fender can be
adjusted to accomodate ordinary or o -road tires.
8
Wheels
The wheels bear the weight of the vehicle and the rider. The tire pressure is 15psi/100kPa.
Please ensure that both tires are equally pressurized before riding the Falcon.
Foot Pads
The foot pads support the rider’s feet. While riding, both feet should always be positioned
in the middle of the pad as shown below.
Battery
The battery provides power to the Falcon. The battery voltage is 70VDC. Do not open the
battery compartment or the vehicle’s control panel - you may be subject to electric shock.
Always shut o the power and dismount the Falcon before charging the battery.
To charge the battery, open the cover at the back of the display panel and plug in the
charger included with the vehicle into the socket.
9
Warning
In the event that the vehicle is not used for an extended period, it is advised to charge the
batteries once every 30 days, otherwise irreversible damage to the battery can occur. At
the bare minimum the battery must be charged once every three months. If the vehicle is
to be stored, disconnect the battery rst.
Do not disassemble or reassemble the battery box, expose it to high pressure, re, or any
heat sources under any circumstances.
Battery
The charger provided uses AC 160V-240V, 50/60Hz. When charging, a red indicator light
should turn on. The light should turn green once the battery is fully charged. When
charging the battery for the rst time, it is normal for it take 5-6 hours. The battery lasts approximately 4 hours per full charge. If the Falcon is not used immediately, it is also advised
to close the circuit breaker to save power.
10
Operating Instructions
When riding for the rst time or if the Falcon has been in a reclined position for a long
time, you must rst initialize the positioner. See Annex 1.
To switch on the vehicle, hold the handlebar while standing in the centre near the rear of
the vehicle. Switch on the vehicle - the display panel should illuminate indicating normal
operation.
When status lights stop circulating, audio cues should be heard from both left and right
motors. This indicates that motors and control system are operating normally.
To mount the vehicle, wait for the 4 red indicator lights in the middle to stop ashing. Step
onto the unit with one foot to feel the balance. If the unit feels balanced, step on the vehicle with your other foot. Keep your body upright to control the unit and achieve stability.
While holding the handlebars, lean forward and the vehicle should move forward slowly.
Lean backwards and it should gradually come to a stop. The Falcon’s forward and reverse
movement is controlled by the rider’s body movement.
Tilting the handlebar controls the direction of the vehicle. You can also lean your body left
or right while turning the handlebars to maintain balance. The turn rate and turning angle
varies according to speed. In general, the greater the angle of the handlebar, the faster the
turn speed. When reversing, the control direction of the handlebars is reversed.
When dismounting, pull back the handlebar and shift your bodyweight to an upright
position. When the vehicle has stopped completely, remove one foot, while holding the
handlebar to maintain stability, then completely dismount. When the vehicle is on, do not
release the handlebar to remain in control of the vehicle. Remember to shut o the vehicle
completely before dismounting.
Warning
If the Anti-Fall function is in use, the safety strap must be attached to the rider’s body before stepping on the vehicle; if the vehicle loses balance, the power will shut o .
Operating Conditions and Maintenance
If the alarm goes o and the handlebars vibrate while riding, slow down. When riding forward at excessive speeds, the handlebar and the whole vehicle will automatically begin to
lean backward to lower the speed - this is a normal function to limit the speed.
Before riding, ensure that the handlebar, wheels, batteries, wheel guards and other parts
are installed correctly and securely. Screws may loosen from vibration during operation.
You may need to tighten screws to avoid loss of power, unwanted vibration or other unwanted vibration that may cause injury.
While riding, if any abnormal sounds are heard, stop the vehicle, dismount, and check the
entire vehicle before proceeding.
Do not attempt to perform a maintenance check or repair the Falcon. In the event of failure, please bring it to an authorized professional. Unauthorized repairs or any attempted
repairs by a non-certi ed professional will invalidate warranties and may incur more repair costs.
11
Parts Replacement Schedule
Directional Potentiometer replace annually or for every 1,000 km traveled
Handlebar Suspension Gas
Springs
Tires
Gearbox oil change oil for every 2,000 km traveled
replace annually or for every 1,000 km traveled
replace both tires if tread depth is less than
0.5mm
12
Annex 1
Using the Remote Control
The top left button controls the power, the lower left
button is the mode key button. The upper right button locks the vehicle, and the lower right button is the
display key.
In the o -state, press and hold the power button for 5
seconds to hear the buzzer “beep.” The battery indicator lights should turn on.
At this time, the status lights should ash. All light indicators may cycle - if this is the case, the systems are
working to properly balance the vehicle. If the lights
continue to cycle, do NOT ride the vehicle - wait for
the status lights to stop ashing before riding.
To power o the Falcon, press the power button while
in standby mode and you should hear a beeping
sound before it turns o .
Locking and Unlocking the Falcon
In standby mode, press the lock key until you hear a “beep” sound. The status lights should
ash on the display panel, and the lights will eventually turn o . It is now in the lock state
- an alarm will trigger and the handlebars will vibrate if the vehicle is touched.
To unlock the vehicle, press the lock button on the remote control again. The status lights
on the display panel should turn on.
13
Calibrating the Balance Point
When riding for the rst time or after an extended period, it is a good idea to calibrate the
system to nd a balance point. While in the o state, press the power button and the mode
button together for two seconds. After a few “beeps,” the vehicle will calibrate its systems.
At this point, the vehicle shoud level the platform and a nal “beep” will con rm that the
calibration is complete. After calibrating, the system will automatically shut down.
Correcting the platform level and directional data
While in standby mode, press the power button and mode display button until you hear
a “beep.” The display lights shouldturn on - from here you can con gure 5 di erent parameters represented on the battery indicator. The rst light adjusts the controls for the
left platform step, the second light controls the right platform. The third and fourth light
adjusts the abatement for both left and right platforms. The fth light adjusts the sensitivity of the steering. To increase the values for each, press the display button to gradually
increase the desired parameter. Upon each button press, the light increases in brightness
incrementally.
Set the running time
Press the power button and lock button until you hear a “beep” to enter the setup. The digital display should read 0. Press the mode key to reduce the number, the power button to
cancel the setting and revert to default, the lock key to save and exit, and the display key
to increase the value.
Digital tube numerical switch
While in standby mode, press the display key to switch the display value - this will display
the value in running time - press it again to cycle display of speed and mileage. To set the
default of which to display on the panel, press the mode key and display key at the same
time while the display is on the desired parameter (running time, speed, or mileage) until
you hear a beep. Press the mode and display key again to save this setting.
Change between high and low speed
By default, the Falcon is set to high speed (20km/h) - press the mode key upon seeing the
frequency display on the panel- the status lights should display a new frequency that represents low speed mode (10km/h).
14
Loading...