Davis 6380 Installation Manual
W
IRELESS
T
EMPERATURE/HUMIDITY
TATION
S
I
NSTALLATION MANUAL
The Wireless Temperature/Humidity Station is for Wireless Vantage ProTM.
OMPONENTS
C
The Wireless Temperature/Humidity Station consists of sensors and a transmitter, protected by a radiation shield.
1-1/2" U-Bolts
1/4" Flat Washers
1/4" Hex Nuts
3-Volt
Lithium
Battery
#8 Flat Washers
#8 Split Lock Washers
#8 Hex Nuts
#8 Wing Nuts
Mounting Bracket
Radiation Shield Assembly
Product # 6380
OOLS FOR SETUP
T
In addition to the hardware provided, you will need some or all of the following materials:
Adjustable wrench or 11/32" wrench and 7/16" wrench
✦
Ballpoint pen or paper clip (small pointed object of some kind)
✦
✦
Drill and 3/16" (5 mm) drill bit (if mounting on a vertical surface)
Four 1/4" x 1-1/2" (38 mm) lag screws (if mounting on a vertical surface)
✦
I
NSTALLATION
S
TEPS
For ease of installation, please follow the steps in the order presented.
Prepare the temperature/humidity station, page 3
✦
Remove shield plates to access the Sensor Interface Module, page 3
✦
Insert the battery, page 4
✦
✦
Set the transmitter ID, page 4
✦
Set ID on the station using DIP switches, page 4
✦
Set the console to recognize the signals, page 5
✦
View current readings, page 6
(If you don’t see readings from the correct Station No., put your
✦
temperature/humidity station in TEST mode, page 6)
✦
Choose a location for the temperature/humidity station, page 7
✦
Test transmission from the proposed mounting location, page 7
Mount the temperature/humidity station, page 8
✦
✦
A note on securing cables, page 11
See “Maintenance” on page 10. For Technical Support, see “Contacting Davis
Instruments” on page 11.
Page 2
REPARING
P
THE
EMPERATURE
T
UMIDITY
/H
TATION
S
Removing Radiation Shield Plates
1. Turn the radiation shield assembly upside down. You need to remove the radiation
shield plates to access the Sensor Interface Module, or “SIM”.
The SIM is where you will install the battery and set the transmitter ID.
2. Remove the wing nuts, lock washers and flat washers.
3. Lift two closed plates and then three open plates, sliding them off the threaded studs.
You should now be able to see the SIM.
Closed Plate
Deployment
Closed Plate
Deployment
Radiation Shield Assembly (upside-down)
Open Plate
Antenna
Hole
Antenna
Hole
Open Plate
#8 Wing Nut
#8 Lock Washer
R
ADIATION
Open Plate
S
HIELD
P
Sensor
Interface
Module
(SIM)
LATES
#8 Flat Washer
R
EMOVING
Preparing the Temperature/Humidity Station Page 3
Applying Power
Insert the 3-volt lithium battery into the battery holder, matching the “+” sign
on the battery with the “+” sign on the SIM.
Consult this drawing to locate the DIP switches. You will work with them during the next installation step.
3-Volt
Lithium
Battery
Antenna
DIP Switches
S
S
ETTING
THE
T
I
ENSOR
RANSMITTER
NTERFACE
M
ID
ODULE
ON
T
EMPERATURE
/H
UMIDITY
S
TATION
Each wireless transmitting station must be set to one of eight transmitter IDs.
DIP switches #1, 2 and 3 on the SIM allow you to control the ID — the “channel” the station will transmit on. (DIP switch #4 is used for transmission testing, not for transmitter ID.)
The transmitter and receiver communicate with each other only when both are set to
the same ID.
The factory default transmitter ID is ‘1’. Looking at the table on the next page,
you can see that means the DIP switches are in the OFF position when each
transmitting station leaves the factory, whether it is an ISS, a temperature/humidity station, or another kind of station.
Since the ISS is included with every Wireless Vantage Pro, the console/receiver
is set to find the ISS on ‘1’. Set your temperature/humidity station to its own
number.
Page 4
Loading...