How it Works
DaVinci
Loading...
CBHA1338
Specifications
13 pgs967.73 Kb0

DaVinci CBHA1338 Specifications

Download
Page 1
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40030A/2021
Page： 1 of 13
Date： May 25, 2021
Million Dollar Baby/ DaVinci/ Babyletto/ Nurseryworks/ DavinciKids/ Babymod/ Billy/ Franklin & Ben/ Million Dollar Baby Classic/ Beast Of Leisure
8700 Rex Rd. Pico Rivera, CA90660, USA
The following merchandise was submitted and identified by the applicant as:
Product Description:
Autumn 4-in-1 Mini Crib & Changer Combo/Mini Toddler Bed Conversion Kit/Twin Size Conversion Kit
Style / Item No. :
4381 / 20399 / 4389
Buyer/Order No. :
Million Dollar Baby
We have tested the submitted sample(s) as requested and the following results were obtained:
Sample information:
Dimensions
Measurement (mm)
Interior dimensions Interior length
949
Interior width
608
The rail height dimensions Lowest position to the
top of the mattress
628
Highest position to the top of the mattress
408
Test Requested: Please refer to the test summary
Test Results： --- See following sheets ---
Date of Receipt: Apr. 20, 2021 & Apr. 21,2021 & Apr. 29,2021 & May 07, 2021 & May 12, 2021 & May 17, 2021 & May 21, 2021
Testing Period: Apr. 20, 2021 ~ May 04, 2021 & May 07, 2021~ May 24, 2021
Page 2
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40030A/2021
Page： 2 of 13
Test Summary:
As specified by client, selected parts of the submitted sample(s) for compliance with
Item
Test Parameter
Conclusion
1
16 CFR 1220 SAFETY STANDARD FOR NON-FULL-SIZE BABY CRIB (Excluding clause 5.20)
Pass
(See results 1)
2
ASTM F406-19 Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards (Excluding clause 5.20)
Pass
(See results 2)
3
The bed’s size is not belong to the toddler bed’s scope, the standard was applied as per client’s request. There may be additional hazards and labeling requirements that are not covered by this standard:
16 CFR Part 1217 SAFETY STANDARD FOR TODDLER BEDS (Excluding clause 8 & 9)
(See results 3)
4
The bed’s size is not belong to the toddler bed’s scope, the standard was applied as per client’s request. There may be additional hazards and labeling requirements that are not covered by this standard : ASTM F1821-19ɛ1 Standard Consumer Safety Specification for Toddler
Beds (Excluding clause 8 & 9)
(See results 4)
5
16 CFR Part 1235 SAFETY STANDARD FOR CHANGING PRODUCTS
Pass
(See results 5)
6
ASTM F2388-18 Standard Consumer Safety Specification for Baby Changing Products for Domestic Use
Pass
(See results 6)
7
16 CFR Part 1130 Requirements for Consumer Registration of Durable Infant or Toddler Products (Excluding sec.1130.8)
(See results 7)
8
CPSIA section 101(f) - Lead in paint/similar surface coating material
Pass
(See results 8)
9
CPSIA section 101(a)(2) - Lead in accessible substrate materials
Pass
(See results 9)
10
CPSIA section 108 - Phthalates (16 CFR 1307) + Prop 65 (w/DIDP)
Pass
(See results 10)
**Remark: The chemical results of No.2, 4, 5, 7, 9 were transferred from report HJ30029A/2021 issued on Apr. 21, 2021 & No.10 were transferred from report HJ10018A/2021 issued on Mar. 11, 2021 & No.11, 12 were transferred from report HJ10011/2021 issued on Feb. 24, 2021 & No.20 were transferred from report HJ10009/2021 issued on Feb. 19, 2021 & No.21 were transferred from report HJ10033/2021 issued on Apr. 08, 2021.
Page 3
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40030A/2021
Page： 3 of 13
Test Results:
1. 16 CFR 1220 SAFETY STANDARD FOR NON-FULL-SIZE BABY CRIB
(Base on ASTM F 406-19 Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards)
Clause
5. General Requirements
Results
5.1 Corner Posts
Pass
5.2 There shall be no hazardous sharp points or edges as defined by 16 CFR 1500.48 and 16 CFR 1500.49 before or after testing to this specification.
Pass
5.3 There shall be no small parts, as defined by 16 CFR1501, before testing or liberated
as a result of testing in accordance with this specification.
Pass
5.4 The paint and surface coating on the product shall comply to 16 CFR 1303.
*Note: The details are shown in Results 8.
*Pass
5.5 There shall be no flammable solids as defined in 16 CFR1500.3 (c) (6) (vi) before or after testing in accordance with this specification
Pass
5.6 Scissoring, Shearing, or Pinching
Pass
5.7 Toy accessories attached to, removed from, or sold with a product, as well as their
means of attachment, must meet applicable requirements of Specification F963
N/A
5.8 Latching and Locking Mechanisms
N/A
5.9 Openings
Pass
5.10 Protective Components
N/A
5.11 Labeling
Pass
5.12 Stability
Pass
5.13 Cord/Strap Length
N/A
5.14 Coil Springs
N/A
5.15 Entrapment in Accessories
Pass
5.16 Mattress
Pass
5.17 Mattresses for Rigid Sided Products
Pass
5.18 Protrusions
Pass
5.19 Bassinet/Cradle Accessories
N/A
5.20 Record Keeping
Excluded
6
Performance Requirements for Rigid Sided Products
6.1 Before and after all testing, the product shall comply with the requirements of
Section 5
Pass
6.2 Crib-Side Height
Pass
6.3 Spacing of Unit Components
Pass
6.4 Hardware
Pass
6.5 Fasteners
Pass
6.6 Construction and Finishing
Pass
6.7 Requirements for Cutouts
N/A
6.10 Plastic Teething Rail
N/A
6.11 Cyclic Test
Pass
6.12 Side(s) or End(s) Latch Testing, or Both
N/A
Page 4
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40030A/2021
Page： 4 of 13
6.13 Mattress Support System Vertical Impact Test Requirements
Pass
6.14 Mattress Support System Testing
Pass
6.15 Crib Side Test Requirements
Pass
6.16 Spindle/Slat Strength Testing
Pass
6.17 Non-full-size crib designs shall allow assembly of key structural elements only in the manufacturer’s recommended use position or have permanent markings that indicate their correct orientation. The markings must be conspicuous in any misassembled state.
Pass
7
Performance Requirements for Mesh/Fabric Products
N/A
9
Marking and Labeling
Pass
10
Instructional Literature
Pass
N/A=Not Applicable
Conclusion：The submitted sample(s) complies with the requirements of 16 CFR 1220 SAFETY STANDARD
FOR NON-FULL-SIZE BABY CRIB (Base on ASTM F 406-19 Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards. (Excluding section 5.20)
2. ASTM F 406-19 Standard Consumer Safety Specification for Non-Full-Size Baby
Cribs/Play Yards
Clause
5. General Requirements
Results
5.1 Corner Posts
Pass
5.2 There shall be no hazardous sharp points or edges as defined by 16 CFR 1500.48
and 16 CFR 1500.49 before or after testing to this specification.
Pass
5.3 There shall be no small parts, as defined by 16 CFR1501, before testing or liberated
as a result of testing in accordance with this specification.
Pass
5.4 The paint and surface coating on the product shall comply to 16 CFR 1303. *Note: The details are shown in Results 8.
*Pass
5.5 There shall be no flammable solids as defined in 16 CFR1500.3 (c) (6) (vi) before
or after testing in accordance with this specification
Pass
5.6 Scissoring, Shearing, or Pinching
Pass
5.7 Toy accessories attached to, removed from, or sold with a product, as well as their
means of attachment, must meet applicable requirements of Specification F963
N/A
5.8 Latching and Locking Mechanisms
N/A
5.9 Openings
Pass
5.10 Protective Components
N/A
5.11 Labeling
Pass
5.12 Stability
Pass
5.13 Cord/Strap Length
N/A
5.14 Coil Springs
N/A
Page 5
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40030A/2021
Page： 5 of 13
5.15 Entrapment in Accessories
Pass
5.16 Mattress
Pass
5.17 Mattresses for Rigid Sided Products
Pass
5.18 Protrusions
Pass
5.19 Bassinet/Cradle Accessories
N/A
5.20 Record Keeping
Excluded
6
Performance Requirements for Rigid Sided Products
6.1 Before and after all testing, the product shall comply with the requirements of Section 5
Pass
6.2 Crib-Side Height
Pass
6.3 Spacing of Unit Components
Pass
6.4 Hardware
Pass
6.5 Fasteners
Pass
6.6 Construction and Finishing
Pass
6.7 Requirements for Cutouts
N/A
6.10 Plastic Teething Rail
N/A
6.11 Cyclic Test
Pass
6.12 Side(s) or End(s) Latch Testing, or Both
N/A
6.13 Mattress Support System Vertical Impact Test Requirements
Pass
6.14 Mattress Support System Testing
Pass
6.15 Crib Side Test Requirements
Pass
6.16 Spindle/Slat Strength Testing
Pass
6.17 Non-full-size crib designs shall allow assembly of key structural elements only in the manufacturer’s recommended use position or have permanent markings that indicate their correct orientation. The markings must be conspicuous in any misassembled state.
Pass
7
Performance Requirements for Mesh/Fabric Products
N/A
9
Marking and Labeling
Pass
10
Instructional Literature
Pass
N/A = Not Applicable
Conclusion：The submitted sample(s) complies with the requirements of ASTM F406-19 Standard Consumer
Safety Specification for Non-Full-Size Baby Cribs/Play Yards. (Excluding clause 5.20)
3. 16 CFR Part 1217 SAFETY STANDARD FOR TODDLER BEDS (Base on ASTM F1821-19
ɛ
1
Standard Consumer Safety Specification for Toddler Beds)
Clause
Results
5. General Requirements:
5.1
The bed shall conform to the regulations specified in Section 2 of this specification before and after testing.
Pass
Page 6
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40030A/2021
Page： 6 of 13
5.2
There shall be no hazardous sharp points or edges as defined by 16 CFR 1500.48 and 16 CFR 1500.49 before and after testing to this consumer safety specification.
Pass
5.3
There shall be no small parts as defined by 16 CFR 1501before testing or liberated as a result of testing to this specification.
Pass
5.4
Product must comply with 16 CFR 1303. *Note: The details are shown in Results 8.
*Pass
5.5
Wood Parts
Pass
5.6
Scissoring, Shearing, Pinching
Pass
5.7
Protective Components
N/A
5.8
Openings
Pass
5.9
Labeling
Pass
5.10
Corner Post Extensions
Pass
6. Performance Requirements:
6.1
Mattress Support System
Pass
6.2
Mattress Support System Attachment to End Structures
Pass
6.3
Mattress Support System Openings
Pass
6.4
Guardrails
Pass
6.5
End Structures and Side
Pass
6.6
Partially Bounded Openings
N/A
6.7
Spindle/Slat Static Load Strength
Pass
8
Marking and Labeling
Excluded
9
Instructional Literature
Excluded
N/A = Not Applicable
4. ASTM F1821-19ɛ1 Standard Consumer Safety Specification for Toddler Beds
Clause
Results
5. General Requirements:
5.1
The bed shall conform to the regulations specified in Section 2 of this specification before and after testing.
Pass
5.2
There shall be no hazardous sharp points or edges as defined by 16 CFR 1500.48 and 16 CFR 1500.49 before and after testing to this consumer safety specification.
Pass
5.3
There shall be no small parts as defined by 16 CFR 1501before testing or liberated as a result of testing to this specification.
Pass
5.4
Product must comply with 16 CFR 1303. *Note: The details are shown in Results 8.
*Pass
5.5
Wood Parts
Pass
5.6
Scissoring, Shearing, Pinching
Pass
5.7
Protective Components
N/A
5.8
Openings
Pass
5.9
Labeling
Pass
5.10
Corner Post Extensions
Pass
Page 7
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40030A/2021
Page： 7 of 13
6. Performance Requirements:
6.1
Mattress Support System
Pass
6.2
Mattress Support System Attachment to End Structures
Pass
6.3
Mattress Support System Openings
Pass
6.4
Guardrails
Pass
6.5
End Structures and Side
Pass
6.6
Partially Bounded Openings
N/A
6.7
Spindle/Slat Static Load Strength
Pass
8
Marking and Labeling
Excluded
9
Instructional Literature
Excluded
N/A = Not Applicable
5. 16 CFR Part 1235 SAFETY STANDARD FOR CHANGING PRODUCTS (Base on ASTM F2388-18 Standard Consumer Safety Specification for Baby Changing Products for Domestic Use)
Clause
Results
5. General Requirements
5.1
Sharp Points and Edges
Pass
5.2
Small Parts
Pass
5.3
Surface Coatings *Note: The details are shown in Results 8.
*Pass
5.4
Wood Parts
Pass
5.5
Openings
Pass
5.6
A changing table accessory
Pass
5.7
Toys
N/A
5.8
Threaded Fasteners
Pass
5.9
Protective Components
N/A
5.10
Product must comply with the applicable requirements of the Consumer Product Safety Improvement Act.
Pass
5.11
Scissoring, Shearing, and Pinching
Pass
5.12
If the changing product can be converted into another product for which a consumer safety specification exists, the product shall comply with the applicable requirements of that standard when in that use mode.
N/A
6. Performance Requirements
6.1
Structural Integrity
Pass
6.2
Stability
Pass
6.3
Barriers
Pass
6.4
Retention of Contoured Changing Pads and Add-on Changing Units
N/A
6.5
Entrapment in Enclosed Openings
Pass
6.6
Entrapment by Shelves
Pass
Page 8
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40030A/2021
Page： 8 of 13
6.7
Self-folding Steps
N/A
6.8
Restraint System
Pass
8. Permanency of Labels and Warnings
Pass
9. Marking and Labeling
Pass
10. Instructional Literature
Pass
N/A = Not Applicable
6. ASTM F2388-18 Standard Consumer Safety Specification for Baby Changing Products for Domestic Use
Clause
Results
5. General Requirements
5.1
Sharp Points and Edges
Pass
5.2
Small Parts
Pass
5.3
Surface Coatings *Note: The details are shown in Results 8.
*Pass
5.4
Wood Parts
Pass
5.5
Openings
Pass
5.6
A changing table accessory
Pass
5.7
Toys
N/A
5.8
Threaded Fasteners
Pass
5.9
Protective Components
N/A
5.10
Product must comply with the applicable requirements of the Consumer Product Safety Improvement Act.
Pass
5.11
Scissoring, Shearing, and Pinching
Pass
5.12
If the changing product can be converted into another product for which a consumer safety specification exists, the product shall comply with the applicable requirements of that standard when in that use mode.
N/A
6. Performance Requirements
6.1
Structural Integrity
Pass
6.2
Stability
Pass
6.3
Barriers
Pass
6.4
Retention of Contoured Changing Pads and Add-on Changing Units
N/A
6.5
Entrapment in Enclosed Openings
Pass
6.6
Entrapment by Shelves
Pass
6.7
Self-folding Steps
N/A
6.8
Restraint System
Pass
8. Permanency of Labels and Warnings
Pass
9. Marking and Labeling
Pass
10. Instructional Literature
Pass
N/A = Not Applicable
Page 9
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40030A/2021
Page： 9 of 13
7. 16 CFR Part 1130 Requirements for Consumer Registration of Durable Infant or Toddler Products
Sec.
Results
1130.3
General requirements
Pass
1130.4
Identification on the product
Pass
1130.5
Requirements for registration forms
Pass
1130.6
Requirements for format and text of registration forms
Pass
1130.7
Requirements for Web site registration or alternative e-mail registration
Pass
1130.8
Recordkeeping and notification requirements
Excluded
Note: See photo E, F, G, H, I & J. The registration forms assessment was based on the submitted samples and the
information provided by the applicant. There was no verification on the validity of such information.
8. CPSIA section 101(f) - Lead in paint/similar surface coating material
Method: With reference to CPSC-CH-E1003-09.1. Analysis was performed by ICP-OES.
9. CPSIA section 101(a)(2) - Lead in accessible substrate materials
Method (non-metallic materials): With reference to CPSC-CH-E1002-08.3. Analysis was performed by
ICP-OES.
Method (metal materials): With reference to CPSC-CH-E1001-08.3. Analysis was performed by ICP-OES.
10. CPSIA section 108 - Phthalates (16 CFR 1307) + Prop 65 (w/DIDP)
Method: With reference to CPSC-CH-C1001-09.4. Analysis was conducted by GC-MS.
Test item
Unit
RL 1 5
11
13
15
Permissible
Limit
Dibutyl Phthalate (DBP)
%
0.005
n.d.
0.0815
n.d.
n.d.
n.d.
0.1%
Benzylbutyl Phthalate (BBP)
%
0.005
n.d.
n.d.
n.d.
n.d.
n.d.
0.1%
Di-(2-ethylhexyl)Phthalate (DEHP)
%
0.005
n.d.
n.d.
n.d.
n.d.
n.d.
0.1%
Diisononyl Phthalate (DINP)
%
0.005
n.d.
n.d.
n.d.
n.d.
n.d.
0.1%
Di-n-hexy1 Phthalate (DNHP/DHEXP)
%
0.005
n.d.
n.d.
n.d.
n.d.
n.d.
0.1%
Di-n-pentyl Phthalate (DPENP)
%
0.005
n.d.
n.d.
n.d.
n.d.
n.d.
0.1%
Di-isobuty1 Phthalate (DIBP)
%
0.005
n.d.
n.d.
n.d.
n.d.
n.d.
0.1%
Di-cyclohexyl Phthalate (DCHP)
%
0.005
n.d.
n.d.
n.d.
n.d.
n.d.
0.1%
Diisodecyl Phthalate (DIDP)
%
0.005
n.d.
n.d.
n.d.
n.d.
n.d.
0.1%
Test item
Unit
RL 1 5
12
13
Permissible
Limit
Lead (Pb)
mg/kg 2 n.d.
n.d.
9.68
n.d.
90 ppm
Test item
Unit
RL
2~4
6~9
10
11
14~19
20
21
Permissible
Limit
Lead (Pb)
mg/kg
2
n.d.
n.d.
2.15
n.d.
n.d.
22.7
n.d.
100 ppm
Page 10
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40030A/2021
Page： 10 of 13
Remark:
(1) The limit is referenced to the requirement stated in Alameda Superior Court,
BG-07-350969 and CPSIA & 16 CFR1307.
(2) The reference limit applied in testing is based on particular California Proposition 65
settlements that are most similar to the tested product in the opinion of the lab. The testing in this report does not reflect a user’s actual exposure to the tested chemical. A manufacturer or retailer that is not named in the referenced settlement is not bound by that settlement, and may choose to comply with California Proposition 65 by clearly informing the consumer of potential exposure.
Sample Description:
1.
Gray coating of sample. (the cover of frame)
2.
Brown wood of sample. (frame's substrate)
3.
Silver colored metal of sample. (2-1/2" phillips head bolt)
4.
Silver colored metal of sample. (1-3/4" allen head bolt)
5.
Black coating of sample. (cover of mattress support)
6.
Silver colored metal of sample. (mattress support's substrate)
7.
Silver colored metal of sample. (plate's substrate)
8.
Silver colored metal of sample. (metal string's substrate)
9.
White paper sticker with black printing of sample. (tracking label)
10.
White paper sticker with black/orange printing of sample. (warning label)
11.
White plastic fabric of sample. (pad cover)
12.
Black coating with white polyester fabric of sample. (label on pad)
13.
Black coating of sample. (the cover of metal sheet)
14.
Silver colored metal of sample. (metal sheet’s substrate)
15.
Brown plastic of sample. (Buckle)
16.
Brown strap of sample.
17.
White fabric with black printing with adhesive of sample. (warning label on strap)
18.
Silver colored metal of sample. (5/8” wood screw on strap)
19.
Silver colored metal of sample. (washer on strap)
20.
Silver colored metal of sample. (CL)
21.
Black paper sticker of sample. (cover of board)
Note :
1. mg/kg = ppm; 0.1wt% = 1000 ppm
2. n.d. = not detected
3. RL = Reporting Limit
4. Results presented in this table are the calculated results based on the above tested components.
6. The content of this report is invalid if it is not presented as the entire report.
7. The statement of conformity is based on the test results, but does not include the measurement uncertainty.
8. The chemical analysis test was conducted in SGS Taiwan Ltd. Chemical lab – Taipei.
Page 11
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40030A/2021
Page： 11 of 13
– Picture(s) –
Photo A: Appearance of the tested crib
-4381
Photo B: Appearance of the tested toddler bed
-20399
Photo C: Appearance of the serious product-4389
Photo D: Appearance of the serious product-4389
Page 12
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40030A/2021
Page： 12 of 13
Photo E: Registration form information-4381
(front)
Photo F: Registration form information-4381
(back)
Photo G: Registration form information-20399
(front)
Photo H: Registration form information-20399
(back)
Page 13
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40030A/2021
Page： 13 of 13
Photo I: Registration form information-4389
(front)
Photo J: Registration form information-4389
(back)
--- End of Report ---
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use