This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic
format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction
issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction,
if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
document cannot
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40031A/2021
Page： 1 of 9
Date： May 25, 2021
Million Dollar Baby/ DaVinci/ Babyletto/ Nurseryworks/ DavinciKids/ Babymod/ Billy/ Franklin
& Ben/ Million Dollar Baby Classic/ Beast Of Leisure
8700 Rex Rd. Pico Rivera, CA90660, USA
The following merchandise was submitted and identified by the applicant as:
Product Description:
Autumn 4-in-1 Mini Crib & Changer Combo/Mini Toddler Bed Conversion
Kit/Twin Size Conversion Kit
Style / Item No. :
4381 / 20399 / 4389
Buyer/Order No. :
Million Dollar Baby
We have tested the submitted sample(s) as requested and the following results were obtained:
Test Requested: Please refer to the test summary
Test Results： --- See following sheets ---
Date of Receipt: Apr. 20, 2021 & Apr. 21,2021 & Apr. 29,2021 & May 07, 2021 & May 12, 2021
& May 17, 2021 & May 21, 2021
Testing Period: Apr. 20, 2021 ~ May 04, 2021 & May 07, 2021~ May 24, 2021
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic
format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction
issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction,
if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
document cannot
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40031A/2021
Page： 2 of 9
Test Summary:
As specified by client, selected parts of the submitted sample(s) for compliance with
Item
Test Parameter
Conclusion
1
SOR/2016-152 Crib, Cradles and Bassinets Regulations
Pass
(See results 1)
2
Sharp points, sharp edges and small parts with reference to Section 7 small
parts, section 8 metal edges, section 10 plastic edges & section 11 Wooden of
Toys Regulations SOR/2011-17 amended up to January 11, 2019 of Canada
Consumer Product Safety Act
Pass
(See results 2)
3
SOR/2016-194 Textile Flammability
Pass
(See results 3)
4
Section 32 Dolls, Plush Toys and Soft Toys: Flammability of outer covering of
Toys Regulations SOR/2011-17 amended up to January 11, 2019 of Canada
Consumer Product Safety Act
Pass
(See results 4)
5
Section 23 Specific substances in surface coatings of Toys Regulations
SOR/2011-17 amended up to January 11, 2019 of Canada Consumer Product
Safety Act
Pass
(See results 6)
6
SOR/2016-193 Lead/ Mercury in surface coatings
Pass
(See results 7)
7
SOR/2018-83 Consumer products containing lead Regulations
Pass
(See results 8)
8
SOR/2016-188 Phthalates Regulations
Pass
(See results 9)
**Remark:
The chemical results of No.2, 4, 5, 7, 9 were transferred from report HJ30031/2021 issued on Apr. 21, 2021 &
No.10 were transferred from report HJ10019A/2021 issued on Mar. 11, 2021 & No.11, 12 were transferred from
report HJ10012/2021 issued on Feb. 24, 2021 & No.20 were transferred from report HJ10010/2021 issued on
Mar. 11, 2021 & No.21 were transferred from report HJ10034B/2021 issued on Apr. 09, 2021.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic
format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction
issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction,
if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
document cannot
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40031A/2021
Page： 3 of 9
Test Results:
1. SOR/2016-152 Crib, Cradles and Bassinets Regulations
Section Description
Results
Requirements for Cribs, Cradles, Bassinets, Accessories and Stands
2
Key structural components — assembly
Pass
3
Surface coating materials
*Note: The details are shown in Results 5.
*Pass
4
Angle
Pass
5
Angle — products that rock or swing
N/A
6
Shearing and pinching
Pass
7
Types of sides
Pass
8
Strength and integrity of slats
Pass
9
Posts
Pass
10
Entrapment
10(1)
Entrapment — cribs
Pass
10(2)
Entrapment — other products
N/A
11
Openings formed or exposed — structural covers
11(1)
Openings formed or exposed — structural covers — cribs
N/A
11(2)
Openings formed or exposed — structural covers — other products
N/A
12
Mesh
12(1)
Mesh — strength and integrity
N/A
12(2)
Size of openings in mesh
N/A
13
Flammability
Pass
14
Entanglement
14(1)
Entanglement — cribs and stands
Pass
14(2)
Entanglement — other products
N/A
15
Parts
15(1)
Parts — wood, plastic or similar hard material
Pass
15(2)
Parts — Metal
Pass
15(3)
Metal tubing
N/A
15(4)
Bolts
Pass
16
Small parts
Pass
17
Openings
Pass
18
Restraint systems
Pass
19
Cords and straps — length
19(1)
Cords and straps — length — general
N/A
19(2)
Cords and straps — length —change table accessory
Pass
20
Cords and straps — loops
20(1)
Cords and straps — loops — general
N/A
20(2)
Cords and straps — loops — change table accessories
Pass
21
Coil springs
N/A
22
Mattress
Pass
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic
format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction
issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction,
if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
document cannot
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40031A/2021
Page： 4 of 9
Additional Requirements for Cribs
23
Structural integrity
Pass
24
Mattress support
Pass
25
Height of sides — mattress support in lowest position
Pass
26
Height of sides — mattress support in highest position
Pass
27
Latching or locking mechanisms of access sides
N/A
28
Latching or locking mechanisms of folding cribs
N/A
29
Slat strength
Pass
30
Toeholds
Pass
Additional Requirements for Accessories
42
Entrapment
42(1)
Entrapment — accessory placed on or fixed to crib
Pass
42(2)
Entrapment — accessory detached or displaced from crib
N/A
43
Structural integrity
Pass
44
Height of sides — sleep accessory
N/A
Presentation of Information
47
Presentation — general
Pass
48
Print
Pass
49
Height of type
49(1)
Signal words
Pass
49(2)
Other information — height of type
Pass
Requirements for Cribs, Cradles, Bassinets, Accessories and Stands
50
Required information
Pass
51
Assembly and use
51(1)
Assembly and use — cribs, cradles and bassinets
Pass
51(2)
Assembly and use — accessories
Pass
51(3)
Exception — accessories supplied with product
Pass
52
Warnings — pouches
Pass
Additional Requirements for Cribs
53
Warning — all cribs
Pass
54
Warning — cribs with access side
N/A
55
Warning — cribs sold without mattress
N/A
56
Warning — cribs with mattress
Pass
57
Warning — cribs designed to be used without mattress
N/A
58
Warning — when crib used as accessory
N/A
Additional Requirements for Accessories
General
71
Non-application
72
Warning
72(1)
Warning — all accessories
Pass
72(2)
Warning — accessories that extend over or into occupant retention area
N/A
73
Warning — accessories other than sleep accessories
N/A
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic
format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction
issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction,
if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
document cannot
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40031A/2021
Page： 5 of 9
Sleep Accessories
74
Warning — sleep accessories
N/A
75
Warning — sleep accessories sold without mattress
N/A
76
Warning — sleep accessories with mattress
N/A
77
Warning — sleep accessories designed to be used without mattress
N/A
N/A = Not Applicable
Conclusion: The submitted sample(s) complies with the requirements of SOR/2016-152 Cribs, Cradles and
Bassinets Regulations.
2. Sharp points, sharp edges and small parts with reference to Toys Regulations SOR/2011-17 amended
up to January 11, 2019 of Canada Consumer Product Safety Act
Section
Description
Results
7
Small parts
Pass
8
Metal edges
Pass
10
Plastic edges
Pass
11
Wooden
Pass
3. SOR/2016-194 Textile Flammability
Flame Resistance - 45°Angle Test - One Second Flame Impingement
(CAN/CGSB-4.2 No.27.5 - 2008)
Sample
:
White plastic sheet (pad)
Fabric Surface
:
Plain
Test Specimen
Direction
:
Length
Original State
Time of flame spread (s)
Flame Spread (sec.)
Burn Code
(1) - DNI
(2) - DNI
(3) - DNI
(4) - DNI
(5) - DNI
(6) - DNI*
(7) - DNI*
(8) - DNI*
(9) - DNI*
(10) - DNI*
Note: DNI = Do Not Ignite
* = Since the initial five specimens did not ignite, five additional specimens were tested.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic
format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction
issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction,
if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
document cannot
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40031A/2021
Page： 6 of 9
Requirement:
Canada Consumer Product Safety Act: Textile Flammability Regulation SOR/2016-194
Banned in Canada if flame spread is:
Plain Surface Fabrics: 3.5 Seconds or less
Conclusion
The submitted sample complies with the flammability requirements for General Textiles Products under Textile
Flammability Regulation SOR/2016-194 of the Canada Consumer Product Safety Act
4. Section 32 Dolls, Plush Toys and Soft Toys: Flammability of outer covering of Toys Regulations
SOR/2011-17 amended up to January 11, 2019 of Canada Consumer Product Safety Act
Section
Description
Result
32
Dolls, Plush Toys and Soft Toys- Flammability of outer covering
Pass
5. SOR/2016-152 Crib, Cradles and Bassinets Regulations: section 3 Surface coating materials
1) Lead and Mercury in surface coating material
Method: With reference to Health Canada Product Safety Reference Manual Book 5 – Laboratory
Policies and Procedures Part B: Test Method Section C-02.2.2(2020). Analysis was performed by ICP-OES.
Test Method Section C-07(2019). Analysis was performed by Mercury Analyzer.
Test Item(s)
Unit
Result
RL
Permissible
Limit
1 5 13
Average of 3 units-Lead (Pb)
mg/kg
N.D.
N.D.
N.D.
20
90
Mercury (Hg)
mg/kg
N.D.
N.D.
N.D.
1
Not detected
2) Soluble heavy metals in surface coating material
Method: With reference to Health Canada Product Safety Reference Manual Book 5 – Laboratory
Policies and Procedures Part B: Test Method Section C-03(2018). Analysis was performed by ICP-OES.
Test Item(s)
Unit
Result
RL
Permissible
Limit
1 5 13
Average of 3 units-Soluble Antimony
(Sb)
mg/kg
N.D.
N.D.
N.D.
50
1000
Average of 3 units-Soluble Arsenic
(As)
mg/kg
N.D.
N.D.
N.D.
50
1000
Average of 3 units-Soluble Cadmium
(Cd)
mg/kg
N.D.
N.D.
N.D.
50
1000
Average of 3 units-Soluble Selenium
(Se)
mg/kg
N.D.
N.D.
N.D.
50
1000
Average of 3 units-Soluble Barium
(Ba)
mg/kg
N.D.
N.D.
N.D.
50
1000
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic
format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction
issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction,
if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
document cannot
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40031A/2021
Page： 7 of 9
6. Section 23 Specific substances in surface coatings of Toys Regulations SOR/2011-17 amended up to
January 11, 2019 of Canada Consumer Product Safety Act
1) Lead and Mercury in surface coating material
Method: With reference to Health Canada Product Safety Reference Manual Book 5 – Laboratory
Policies and Procedures Part B: Test Method Section C-02.2.2(2020). Analysis was performed by ICP-OES.
Test Method Section C-07(2019). Analysis was performed by Mercury Analyzer.
Test Item(s)
Unit
Result
RL
Permissible
Limit
1 5 13
Average of 3 units-Lead (Pb)
mg/kg
N.D.
N.D.
N.D.
20
90
Mercury (Hg)
mg/kg
N.D.
N.D.
N.D. 1 10
2) Soluble heavy metals in surface coating material
Method: With reference to Health Canada Product Safety Reference Manual Book 5 – Laboratory
Policies and Procedures Part B: Test Method Section C-03(2018). Analysis was performed by ICP-OES.
Test Item(s)
Unit
Result
RL
Permissible
Limit
1 5 13
Average of 3 units-Soluble Antimony
(Sb)
mg/kg
N.D.
N.D.
N.D.
50
1000
Average of 3 units-Soluble Arsenic
(As)
mg/kg
N.D.
N.D.
N.D.
50
1000
Average of 3 units-Soluble Cadmium
(Cd)
mg/kg
N.D.
N.D.
N.D.
50
1000
Average of 3 units-Soluble Selenium
(Se)
mg/kg
N.D.
N.D.
N.D.
50
1000
Average of 3 units-Soluble Barium
(Ba)
mg/kg
N.D.
N.D.
N.D.
50
1000
7. SOR/2016-193 Lead/ Mercury in surface coatings
Method: With reference to Health Canada Product Safety Reference Manual Book 5 – Laboratory
Policies and Procedures Part B: Test Method Section C-02.2.2(2020). Analysis was performed by ICP-OES.
Test Method Section C-07(2019). Analysis was performed by Mercury Analyzer.
Test Item(s)
Unit
Result
RL
Permissible
Limit
1 5 13
Average of 3 units-Lead (Pb)
mg/kg
N.D.
N.D.
N.D.
20
90
Mercury (Hg)
mg/kg
N.D.
N.D.
N.D. 1 10
8. SOR/2018-83 Consumer products containing lead Regulations
Method : With reference to Health Canada Product Safety Reference Manual Book 5 – Laboratory
Policies and Procedures Part B: Test Method Section C-02.3(2017) & C-02.4.1(2019).
Analysis was performed by ICP-OES.
Test Item(s)
Unit
Result
RL
Permissible
Limit
2~4
6~12
14~19
20
21
Average of 3 units-Lead (Pb)
mg/kg
N.D.
N.D.
N.D.
22.9
N.D.
20
90
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic
format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction
issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction,
if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
document cannot
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40031A/2021
Page： 8 of 9
9. SOR/2016-188 Phthalates Regulations
Method : With reference to Health Canada Product Safety Reference Manual Book 5 – Laboratory
Policies and Procedures Part B: Test Method Section C-34.2(2018).
Analysis was performed by GC-MS.
Test Item(s)
Unit
Result (%)
RL
Permissible
Limit
1 5 11
13
15
Dibutyl Phthalate (DBP)
%
N.D.
0.0403
N.D
N.D.
N.D.
0.003
0.1
Benzylbutyl Phthalate (BBP)
%
N.D.
N.D.
N.D.
N.D.
N.D.
0.003
0.1
Bis-(2-ethylhexyl) Phthalate
(DEHP)
%
N.D.
N.D.
N.D.
N.D.
N.D.
0.003
0.1
Diisononyl Phthalate (DINP)
%
N.D.
N.D.
N.D.
N.D.
N.D.
0.01
0.1
Di-n-octyl Phthalate (DNOP)
%
N.D.
N.D.
N.D.
N.D.
N.D.
0.003
0.1
Diisodecyl Phthalate (DIDP)
%
N.D.
N.D.
N.D.
N.D.
N.D.
0.01
0.1
Sample Description:
1.
Gray coating of sample. (the cover of frame)
2.
Brown wood of sample. (frame's substrate)
3.
Silver colored metal of sample. (2-1/2" phillips head bolt)
4.
Silver colored metal of sample. (1-3/4" allen head bolt)
5.
Black coating of sample. (cover of mattress support)
6.
Silver colored metal of sample. (mattress support's substrate)
7.
Silver colored metal of sample. (plate's substrate)
8.
Silver colored metal of sample. (metal string's substrate)
9.
White paper sticker with black printing of sample. (tracking label)
10.
White paper sticker with black/orange printing of sample. (warning label)
11.
White plastic fabric of sample. (pad cover)
12.
Black coating with white polyester fabric of sample. (label on pad)
13.
Black coating of sample. (the cover of metal sheet)
14.
Silver colored metal of sample. (metal sheet’s substrate)
15.
Brown plastic of sample. (Buckle)
16.
Brown strap of sample.
17.
White fabric with black printing with adhesive of sample. (warning label on strap)
18.
Silver colored metal of sample. (5/8” wood screw on strap)
19.
Silver colored metal of sample. (washer on strap)
20.
Silver colored metal of sample. (CL)
21.
Black paper sticker of sample. (cover of board)
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic
format d
ocuments, subject to Terms and Conditions for Electronic
Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction
issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction,
if any. The
Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This
document cannot
be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful
and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.
SGS Taiwan Ltd. No.127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan /新北市新北產業園區五工路127 號
台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2299-2920 www.tw.sgs.com
Member of SGS Group
TEST REPORT
Hardline Laboratory Report No.： HJ40031A/2021
Page： 9 of 9
– Picture(s) –
Photo A: Appearance of the tested crib
-4381
Photo B: Appearance of the serious product
-20399
Photo C: Appearance of the serious product-4389
Photo D: Appearance of the serious product-4389
--- End of Report ---
Note :
1. mg/kg = ppm; 0.1wt% = 1000 ppm
2. n.d. = not detected
3. RL = Reporting Limit
4. Results presented in this table are the calculated results based on the above tested components.
5. The content of this report is invalid if it is not presented as the entire report.
6. The statement of conformity is based on the test results, but does not include the measurement
uncertainty.
7. The chemical analysis test was conducted in SGS Taiwan Ltd. Chemical lab – Taipei.
Loading...