DATASHEETS tda4860 DATASHEETS (Philips)

INTEGRATED CIRCUITS

DATA SH EET

TDA4860

Vertical deflection power amplifier
for monitors

Product specification
Supersedes data of September 1991
File under Integrated Circuits, IC02

1996 Nov 26

Philips Semiconductors Product specification

Vertical deflection power amplifier for

TDA4860

monitors

FEATURES

• Vertical pre-amplifier with differential inputs

• Powerless vertical shift

• Flyback voltage generation suitable for two operating

modes (doubling the supply voltage or external supply
for the short flyback time, this achieves a minimum of
power dissipation)

• Vertical output stage with thermal and SOAR protection

• High deflection frequency up to 140 Hz

• High linear sawtooth signal amplification

• Possibility of guarding the deflection

• Voltage stabilizer.

QUICK REFERENCE DATA

Measurements referenced to substrate (pin 6).

SYMBOL PARAMETER MIN. TYP. MAX. UNIT

V

P1

V

P2

V

P3

I

P1

I

P2

V

I

I

5M

T

amb

supply voltage (pin 1) 9 − 30 V
supply voltage (pin 4) 9 − 60 V
flyback supply voltage (pin 8) 9 − 60 V
supply current (pin 1) −−10 mA
supply quiescent current (pin 4) − 9 − mA
input voltage (pins 2 and 3) 1.6 − VP1− 0.5 V
deflection output current (maximum value; pin 5) −−±1A
operating ambient temperature −20 − +75 °C

GENERAL DESCRIPTION

The TDA4860 is a vertical power amplifier for differential
input signals suitable for colour monitor/TV systems with
deflection frequencies up to 140 Hz.

ORDERING INFORMATION

TYPE

NUMBER

NAME DESCRIPTION VERSION

PACKAGE

TDA4860 SIL9MPF plastic single in-line medium power package with fin; 9 leads SOT110-1

1996 Nov 26 2

Philips Semiconductors Product specification

Vertical deflection power amplifier for
monitors

BLOCK DIAGRAM

handbook, full pagewidth

TDA4860

VOLTAGE

STABILIZER

VERTICAL

DRIVER

DIFFERENTIAL

INPUT

AMPLIFIER

THERMAL AND

SOAR

PROTECTION

VERTICAL

OUTPUT

FLYBACK

DRIVER

FLYBACK

GENERATOR

TDA4860

PULSE

CIRCUIT

V

P1

+

8.8 V

470

150 kΩ

from TDA4850

V-shift

Assumed values:
I

= 1.42A.

yoke

R

= 4.17 Ω +7%+∆R(T) =6.12 Ω.

yoke

L

= 5.25 mH.

yoke

R1= 1.0 Ω±1%.
T

=65°C.

amb

T

= 105 °C.

j(max)

T

=75°C.

yoke

P

= 1.2 W.

yoke

PIC= 1.8 W.
P

= 3.0 W.

tot

t

= typically 250 µs.

p FLB

Attention: the heatsink of the IC must be isolated against ground; the cooling fin is connected to pin 6.

µF

1 MΩ

1.8 kΩ

1.8 kΩ

BAX13

270 Ω

R1

1 Ω

V-OUT SUB FLB

V

P2

5.6 Ω

0.1 µF

yoke

−

8.1 V

470 µF

V

N

470 µF

4.3 Ω

87654321 9
V

+

52 V

P3

10 kΩ

R

PCO

PCO

MHA591

Fig.1 Block diagram and application circuit with flyback supply voltage VP3 from an external source.

Deflection frequency range from 50 Hz to 100 Hz.

1996 Nov 26 3

Philips Semiconductors Product specification

Vertical deflection power amplifier for
monitors

PINNING

SYMBOL PIN DESCRIPTION

V

P1

INP1 2 input 1 of differential input amplifier
INP2 3 input 2 of differential input amplifier
V

P2

V-OUT 5 vertical output
SUB 6 substrate
FLB 7 flyback generator output
V

P3

PCO 9 pulse circuit output

1 supply voltage 1

supply voltage 2 for vertical output

4

stage

8 flyback supply voltage 3

handbook, halfpage

V

1

P1

INP1

2

INP2

3

V

4

P2

V-OUT

5

TDA4860

SUB

6
7

FLB

V

8

P3

9

PCO

MHA593

Fig.2 Pin configuration.

TDA4860

FUNCTIONAL DESCRIPTION
Differential input amplifier

The differential sawtooth input signal (coming from a ramp
output of the TDA4850 for example) is fed to the input
pins 2 and 3. The non-inverted signal is attached to pin 3.
The vertical feedback signal is superimposed on the
inverted input signal on pin 2.

Vertical shift is applied at the inputs in a power-less way
(see Fig.1).

Flyback generator

Signals for the flyback generator and the pulse circuit are
generated in the flyback driver stage. The flyback output
consists of a Darlington transistor and a flyback diode.
The flyback generator can operate in two modes:

1. An external supply voltage is applied for the short
flyback time, thus the power dissipation is minimum
(see Fig.1).

2. The flyback voltage is generated by doubling the
supply voltage (see Fig.5). The 100 µF capacitor C2
between pins 4 and 7 is charged up to V

during

P1

scan, using the external diode and the resistor R2.
The cathode of the capacitor C2 is connected to the
positive rail during flyback. Thus, the flyback voltage is
twice the supply voltage.

Vertical output

The vertical output stage is a quasi-complementary
class-B amplifier with a high linearity. The output contains
SOAR (short-circuit protection) and thermal protection.
The output current on pin 5 is reduced for a short time
(to let the temperature decrease to Tj< 150 °C), when the
junction temperature (Tj) exceeds 160 °C.

Deflection GUARD

Pin 9 will go HIGH if the junction temperature goes to high
(see Fig.3). A pulse signal with 50% duty cycle is output on
pin 9, if the deflection coil is open-circuit. A flyback pulse
signal is output at normal conditions.

Further watching can be achieved by means of an external
GUARD circuit as shown in Fig.4. The 22 µF capacitor is
charged during flyback time (V

) at normal conditions.

5>V8

In case of failures, the capacitor is discharged and the
GUARD output goes HIGH.

GUARD output level (see Fig.4):

• LOW for normal conditions

• HIGH for deflection coil short-circuit respectively

open-circuit

• HIGH when there are neither input or output signals.

1996 Nov 26 4

Philips Semiconductors Product specification

Vertical deflection power amplifier for

TDA4860

monitors

LIMITING VALUES

In accordance with the Absolute Maximum Rating System (IEC 134); voltages referenced to substrate (pin 6); unless
otherwise specified.

SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT

V

P1

V

P2

V

P3

V

2,3,9

V

5,7

I

4

I

5 (M)

I

7 (M)

I

9

T

stg

T

amb

T

j

V

es

supply voltage (pin 1) − 40 V
supply voltage (pin 4) − 60 V
supply voltage (pin 8) − 60 V
voltage on pins 2, 3 and 9 − V

P1

V
voltage on pins 5 and 7 − 60 V
current on pin 4 − 1A
output current on pin 5 (peak value) note 1 −±1.3 A
flyback current on pin 7 (peak value) −±1.3 A
current on pin 9 −−8mA
storage temperature −25 +150 °C
operating ambient temperature −20 +75 °C
junction temperature note 1 − 168 °C
electrostatic handling for all pins note 2 −±300 V

Notes

1. Internally limited by thermal protection; switching temperature point at 160 ±8 °C.

2. Equivalent to discharging a 200 pF capacitor through a 0 Ω series resistor.

THERMAL CHARACTERISTICS

SYMBOL PARAMETER VALUE UNIT

R

th j-c

thermal resistance from junction to case 10 K/W

The heatsink can be estimated according to application circuit (see Fig.1):

T

R

th j-a

A heatsink is needed at R
R

th h-a

R

++

th j-cRth c-hRth h-a

< 10 K/W and R

th j-c

= 22.2 K/W − (10 + 0.5) K/W = 11.7 K/W.

–

j(max)Tamb

---------------------------------- ­P

IC(max)

105 °C65°C–

---------------------------------------- -

1.8 W

= 0.5 K/W (using silicon grease) with

th c-h

22.2 K/W====

.

1996 Nov 26 5

Philips Semiconductors Product specification

Vertical deflection power amplifier for

TDA4860

monitors

CHARACTERISTICS

VP1=VP2= 25 V; VN=V6=0V; T

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

V

P1

V

P2

V

P3

I

P1

I

P2

supply voltage 1 (pin 1) 9 25 30 V
supply voltage 2 (pin 4) 9 25 60 V
supply voltage 3 (pin 8) 9 − 60 V
supply current (pin 1) −−10 mA
quiescent supply current (pin 4) without input signal − 9 − mA

Pre-amplifier

V

2,3

I

2,3

input voltage (pins 2 and 3) 1.6 − VP1− 0.5 V
input quiescent current without input signal − 100 − nA

Flyback generator

V
I

7(M)

7

output voltage upper value; I7= −1A − VP3− 2.2 − V
flyback output current

(maximum value; pin 7)

V

1-5

t

p FLB

threshold voltage to switch flyback on/off threshold − 1.4 − V

flyback pulse time see Figs 1 and 3 − 250 −µs
Vertical output; see Fig.3
V

I

5(M)

5

output voltage upper value; I5= −1A VP2− 2.3 VP2− 2 − V

vertical output current

(maximum value; pin 5)
LIN non-linearity of output signal −−1%

=25°C; voltages referenced to substrate (pin 6); unless otherwise specified.

amb

−−±1A

lower value; I

=1A − 1.5 1.7 V

5

−−±1A

Pulse circuit output; see Fig.3
V

9

output voltage R

PCO

see Fig.1

V

9

output voltage for thermal protection

active
V

1-5

t

p9

voltage to insert flyback pulse on pin 9 normal condition −−1.4 V

pulse width deflection open-circuit − 50 − %

normal condition t

1996 Nov 26 6

=10kΩ;

0.4 − VP1− 0.4 V

VP1− 0.4 −−V

p FLB

−−µs

Philips Semiconductors Product specification

Vertical deflection power amplifier for
monitors

handbook, full pagewidth

INP1

INP2

V-OUT

tp

FLB = 250 µs

TDA4860

input signal
on pin 2

t

input signal
on pin 3

t

output signal
on pin 5

PCO

PCO

PCO

t

p9

50%

t

output signal
on pin 9 for
normal condition

t

output signal 
on pin 9 for deflection 
unit open-circuit

t

output signal 
on pin 9 for thermal 
protection active


t

MEH264

1996 Nov 26 7

Fig.3 Vertical timing.

Philips Semiconductors Product specification

Vertical deflection power amplifier for
monitors

APPLICATION INFORMATION

8

5

V

P3

BAX13

2.2 Ω 3.3 kΩ

vertical

output
signal

, full pagewidth

TDA4860

Fig.4 GUARD circuit application on vertical output.

2N5819

22 µF

>1 kΩ

220 kΩ

V

P

BC548

TDA4860

GUARD output
HIGH = error

MEH262

handbook, full pagewidth

+

9 V

470
µF

from TDA4850

VOLTAGE

STABILIZER

V

P1

150 kΩ

V-shift

DIFFERENTIAL

1 MΩ

VERTICAL

DRIVER

INPUT

AMPLIFIER

1.8 kΩ

1.8 kΩ

TDA4860

BAX13

270 Ω

R1

1 Ω

THERMAL AND

SOAR

PROTECTION

VERTICAL

OUTPUT

V-OUT SUB FLB

V

P2

C2 100 µF

5.6 Ω

0.1 µF

5.25 mH

yoke

−

7.8 V

470 µF

V

GENERATOR

R2 240 Ω

N

FLYBACK

DRIVER

FLYBACK

PULSE

CIRCUIT

87654321 9
V

P3

10 kΩ

R

PCO

PCO

MHA592

Fig.5 Application for flyback voltage generation by doubling the supply voltage.

1996 Nov 26 8

Philips Semiconductors Product specification

Vertical deflection power amplifier for
monitors

handbook, full pagewidth

V

P1

12 3 657894

cooling fin

TDA4860

V-OUTINP2INP1

V

P2

SUB PCOV

TDA4860

P3

MEH266

Fig.6 Internal circuitry.

1996 Nov 26 9

Philips Semiconductors Product specification

Vertical deflection power amplifier for
monitors

PACKAGE OUTLINE

SIL9MPF: plastic single in-line medium power package with fin; 9 leads

D

D

1

q

P

P

1

q

2

q

1

TDA4860

SOT110-1

A

2

A

3

pin 1 index

seating plane

19

Z

b

DIMENSIONS (mm are the original dimensions)

A

A

18.5

17.8

max.

3.7

2

A

A

3

4

8.7

15.8

8.0

15.4

UNIT

mm

Note

1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.

e

2

b

0.67

0.50

b

1

2

1.40

0.48

1.14

0.38

bcD

1.40

1.14

b

b

1

0 5 10 mm

scale

(1)

D

1

21.8

21.4

21.4

20.7

w M

(1)

E

eLPP

6.48

6.20

2.54

3.9

3.4

A

A

4

L

Q

q1q

q

Q

1

3.4

3.2

1.75

1.55

15.1

14.9

4.4

4.2

2.75

2.50

c

5.9

5.7

E

2

w

0.25

(1)

Z

max.

1.0

OUTLINE
VERSION

SOT110-1

1996 Nov 26 10

REFERENCES

IEC JEDEC EIAJ

EUROPEAN

PROJECTION

ISSUE DATE

92-11-17
95-02-25

Philips Semiconductors Product specification

Vertical deflection power amplifier for
monitors

SOLDERING
Introduction

There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.

This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in

“IC Package Databook”

our

Soldering by dipping or by wave

The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.

(order code 9398 652 90011).

TDA4860

The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.

Repairing soldered joints

Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.

stg max

). If the

DEFINITIONS

Data sheet status

Objective specification This data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specification This data sheet contains final product specifications.

Limiting values

Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.

Application information

Where application information is given, it is advisory and does not form part of the specification.

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.

1996 Nov 26 11