Page 1
ALUMINUM ELECTROLYTIC CAPACITORS
U1W2T314C5160708M9C10L11112G13B
14
Configuration
Package code
Size code
Capacitance tolerance (±20%)
Rated capacitance (10µF)
Rated voltage (16V)
Series name
Type
φD
3
4 to 10
φD
3 to 8 (5.4L)
6.3 to 10 (L 5.8)
φD
3 to 8 (L 7.7)
8 to 10 (L = 10)
code
CL
NL
A
B
C
3
×
5.4
1.5
3.3
3.3
4 × 5.4
1.8
4.3
4.3
5 × 5.4
2.1
5.3
5.3
6.3 × 5.4
2.4
6.6
6.6
6.3 × 5.8
2.4
6.6
6.6
6.3 × 7.7
2.4
6.6
6.6
8 × 5.4
3.3
8.3
8.3
8 × 10
2.9
8.3
8.3
10
3.2
10.3
10.3
φD × L
Chip Type, Wide Temperature Range
UWT
Chip type operating over wide temperature range of to – 55 to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
Low
UWF
impeadance
Long Life
UUT
Specifications
Perfo rmance Characteristic sItem
Categ ory
Temp erature Range
Rated Voltage Range
Rated Capacitance Range
Capac itance Tolerance
Leaka ge Current
Tangent of loss angle (tan δ)
Stabi lity at Low Temperatu re
Endur ance
Shelf Life
Resis tance to soldering
heat
Marki ng
–55 to +105°C
4 to 50V
1 to 1500µF
±20% at 120Hz, 20°C
After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.
Rated volta ge (V)
tan δ (MAX .)
Imped ance ratio
ZT / Z20 (MAX.)
The specifications listed at right shall be
met when the capacitors are restored to
20°C after the rated voltage is applied for
1000 hours at 105°C.
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the
The capacitors are kept on a hot plate for 30 seconds, which
is maintained at 250°C. The capacitors shall meet the
characteristic requirements listed at right when they are
removed from the plate and restored to 20°C.
Rated volta ge (V)
4
0.40
Z–25°C / Z+20°C
Z–40°C / Z+20°C
6.3
0.30
10
0.24
4
7
15
Capac itance
chang e
tan δ
Leaka ge cur rent
6.3
4
8
Black print on the case top.
UWZ
High
Temperature
Reflow
UWT
Smaller
UZT
Measurement frequency : 120Hz at 20°C
16
0.20
10
25
0.16
Measu rement frequ ency : 120Hz
16
3
2
8
4
Within ±25% of the initial capacitance value for capacitors of
Within ±20% of the initial capacitance value for capacitors of 25V or more.
35
0.14
25
2
4
50
0.14
35
50
2
2
3
3
3mm unit, and 16V or less
φ
200% or less than the initial specified value
Less than or equal to the initial specified value
endurance
characteristics listed above.
Capac itance chang e
tan δ
Leaka ge cur rent
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
.
Chip Type
(φ3 to φ8 × 5.4 )
Capacitance
105˚C Marking
A2P1016V
2
Lot No.
(φ8 × 10, φ10 × 10 )
Capacitance
105˚C Marking
Trade mark
A2P
100
35V
Lot No.
1. Voltage mark for 6.3V is 6V . In case of marking for φ3 units, “V” for rated
voltage is omitted.
2. In case of marking for φ3 units. Lot No is expressed by a digit (month code).
Dimension table in next page.
Plastic platform
1
Voltage
φD±0.5
(L±0.3)
3 Apply to φ6.3 × 5.8, φ6.3 × 7.7
Plastic platform
1
Voltage
φD±0.5
L±0.5
Pressure relief vent
0.3 MAX.
L
0.3 MAX.
Configuration
φD
3 to 8 (L 7.7)
8 to 10 (L = 10)
6.3 × 7.7
2.4
6.6
6.6
2.2
7.7
0.5 to 0.8
F)
µ
code
CL
NL
8 × 5.4
3.3
8.3
8.3
2.3
5.4
0.5 to 0.8
φD
3 to 8 (5.4L)
6.3 to 10 (L 5.8)
Package code
φD
3
4 to 10
8 × 10
2.9
8.3
8.3
3.1
10
0.8 to 1.1
code
GB
GS
Size code
code
(mm)
10 × 10
3.2
10.3
10.3
4.5
10
0.8 to 1.1
2
1
Type numbering system (Example : 16V 10
Positive
C±0.2
B±0.2
+0.1
–0.2
3
H
C±0.2
B±0.2
H
0.5 MAX.
E
A±0.2 A±0.2
Negative
Positive
0.5 MAX.
E
A±0.2 A±0.2
Negative
U1W2T314C5160708M9C10L11112G13B
Capacitance tolerance (±20%)
φD × L
×
3
5.4
4 × 5.4
A
1.5
1.8
B
3.3
4.3
C
3.3
4.3
E
0.8
1.0
L
5.4
5.4
H
0.5 to 0.8
114
0.5 to 0.8
14
Rated capacitance (10µF)
Rated voltage (16V)
Series name
5 × 5.4
6.3 × 5.4
2.1
2.4
5.3
6.6
5.3
6.6
1.3
2.2
5.4
5.4
0.5 to 0.8
0.5 to 0.8
Type
6.3 × 5.8
2.4
6.6
6.6
2.2
5.8
0.5 to 0.8
Page 2
ALUMINUM ELECTROLYTIC CAPACITORS
UWT
Dimensions
V
Cap. (µF)
1
2.2
3.3
4.7
10
22
33
47
100
150
220
330
470
680
1000
1500
( ) is also available with φ3mm upon request. In such a case, 2will be put at 12th digit of type numbering system.
Size φ6.3 × 5.8 is available for capacitors marked. "
Code
010
2R2
3R3
4R7
100
220
330
470
101
151
221
331
471
681
102
152
4 × 5.4
5 × 5.4
5 × 5.4
6.3 × 5.4
6.3 × 5.8
6.3 × 7.7
8 × 10
8 × 10
8 × 10
10 × 10
8 × 5.4
0G
4
22
30
36
60
86
102
(91)
105
210
210
230
310
4 × 5.4
5 × 5.4
5 × 5.4
6.3 × 5.4
6.3 × 5.8
8 × 5.4
6.3 × 7.7
8 × 10
8 × 10
8 × 10
10 × 10
6.3
0J
22
30
36
60
86
102
(91)
105
210
210
230
310
" In such a case,
5 × 5.4
5 × 5.4
6.3 × 5.4
6.3 × 5.4
6.3 × 5.8
6.3 × 7.7
8 × 10
8 × 10
10 × 10
10 × 10
10
1A
27
35
46
60
86
105
195
210
310
310
6
will be put at 12th digit of type numbering system.
4 × 5.4
5 × 5.4
6.3 × 5.4
6.3 × 5.4
6.3 × 5.4
6.3 × 7.7
6.3 × 7.7
8 × 10
8 × 10
10 × 10
16
1C
4 × 5.4
18
(14)
30
40
50
60
95
105
195
230
310
5 × 5.4
6.3 × 5.4
6.3 × 5.4
8 × 5.4
6.3 × 7.7
8 × 10
8 × 10
8 × 10
10 × 10
(3)
25
1E
(3)
35
1V
4 × 5.4
7.5
9
15
25
42
59 (52)
63
84
155
190
300
4 × 5.4
4 × 5.4
5 × 5.4
6.3 × 5.4
6.3 × 7.7
6.3 × 7.7
8 × 10
10 × 10
10 × 10
Case size
φ D × L (mm)
3 × 5.4
3 × 5.4
4 × 5.4
13
(10)
5 × 5.4
23
6.3 × 5.4
38
48
66
91
140
155
190
300
8 × 5.4
6.3 × 5.8
(59)
6.3 × 7.7
8 × 10
8 × 10
10 × 10
Rated ripple current (mArms) at 105°C 120Hz
8 × 5.4
50
1H
(3)
(3)
6.3 (5.9)
11 (9)
14
19
30
51
(45)
60
63
140
180
220
Rated
ripple
Frequency coefficient of rated ripple current
Frequency
Coefficient
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please select UUX(p.156), UUJ(p.162) series if high
C/V products are reqired.
Please refer to page 3 for the minimum order quantity.
50 Hz 120 Hz 300 Hz 1 kHz
0.70 1.00 1.17 1.36 1.50
10 kHz or more
115
Loading...