Datasheet UHE series Specification

ALUMINUM ELECTROLYTIC CAPACITORS

d

Miniature Sized, Low Impedance,
High Reliability

UHE

Low impedance and high reliability withstanding 4000 hours to 10000 hours.
Compliant to the RoHS directive (2011/65/EU,(EU)2015/863).

UHE

Specifications

ltem

Category

Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Leakage Current

Tangent of loss angle (tan

Stability at Low Temperature

Endurance

Marking

–40 to +105˚C

6.3 to 100V

2.2 to 18000µF

± 20% at 120Hz, 20˚C

After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV or 3 (µA), whichever is greater.

Rated voltage (V)

)

δ

tan

δ

(MAX.)

6.3 10 16 25 35 50 63 100

0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08

For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF.

Rated voltage (V)

Impedance ratio

(MAX.)

Z–25˚C / Z+20˚C

Z–40˚C / Z+20˚C

6.3 10 16 25 35 50 63 100

4 3 2 2 2 2 2 2

8 6 4 3 3 3 3 3

The following specifications shall be met when the capacitors are restored to 20˚C after D.C. bias plus rated ripple current is
applied at 105

Rated voltage

, the peak voltage shall not exceed the rated voltage.

˚C

Case size

6.3 to 10V

16 to 100V

<

φD

6.3 φD = 8 , 10 φD

=

4000 hours 6000 hours 8000 hours

5000 hours 7000 hours 10000 hours

Capacitance change Within ± 25% of the initial capacitance value

tan δ 200% or less than the initial specified value

Leakage current Less than or equal to the initial specified value

Printed with white color letter on black sleeve.

Performance Characteristics

Long Life

UHD

Approved by Reliability Center for Electronic
Component, Japan-Certification No. RCJ-03-23C

>

12.5

=

120Hz

20˚C

120Hz

Radial Lead Type

Sleeve (P.E.T.)

0.5MAX.

+

φD

+

MAX.

Pressurerelief vent

L

(φ6.3up)

(L < 20) 1.5
(L 20) 2.0

Please refer to the Guidelines for Aluminum Electrolytic Capacitors

for end seal configuration information.

φ

MIN

5

MIN

4

6.3

2.5

3.5

0.5 0.6

10

8

12.5

5.0

0.6

15

φD

P

2.0

φd

0.5

In case L > 25 for the φ12.5 dia. unit, lead dia. φd = 0.8mm

Frequency coefficient of rated ripple current

Cap. (µF)

Frequency

2.2 to 33

39 to 330

390 to 1000

1200 to 18000

Dimension table in next page.

50Hz 120Hz 300Hz 1kHz

0.45

0.60

0.65

0.75

0.55

0.70

0.75

0.80

0.70

0.85

0.90

0.95

5.0167.5

0.6 0.8

(mm)

18

7.5

0.8

0.90

0.95

0.98

1.00

±0.5

P

10kHz or more

1.00

1.00

1.00

1.00

Type numbering system (Example : 10V 1000µF)

11 12

U1H2E314A5160728M9P10D

Configuration

Capacitance tolerance ( ±20%)

Rated capacitance (1000

Rated voltage (10V)

Series name

Configuration

12.5 to 18 HD

Pb-free leadwire

φ D

Pb-free PET sleeve

5

6.3 ED

8 · 10 PD

DD

CAT.8100K

Size code

µF)

Type

ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS

UHE

Rated Voltage

（V）

（code）

Rated

Capacitance

（µF）

Case Size

φD×L（mm）

tan δ

Leakage Current

（µA）

Impedance（Ω）

MAX.

Rated Ripple

（mArms）

（105℃/100kHz）

Part Number

（

at 20℃ after

2 minutes

）

20℃/

100kHz

－10℃/
100kHz

10

（1A）

5600 18×20 0.27 560 0.026 0.067 2860 UHE1A562MHD3

6800 16×31.5 0.29 680 0.017 0.050 3450 UHE1A682MHD

6800 18×25 0.29 680 0.019 0.049 3140 UHE1A682MHD6

8200 16×35.5 0.33 820 0.015 0.044 3610 UHE1A822MHD

8200 18×31.5 0.33 820 0.015 0.040 4170 UHE1A822MHD6

10000 16×40 0.37 1000 0.013 0.038 4080 UHE1A103MHD

10000 18×35.5 0.37 1000 0.014 0.038 4220 UHE1A103MHD6

12000 18×40 0.41 1200 0.012 0.032 4280 UHE1A123MHD

16

（1C）

56 5×11 0.16 8.96 0.58 2.30 210 UHE1C560MDD

120 6.3×11 0.16 19.2 0.22 0.87 340 UHE1C121MED

330 8×11.5 0.16 52.8 0.13 0.52 640 UHE1C331MPD

470 8×15 0.16 75.2 0.087 0.35 840 UHE1C471MPD

470 10×12.5 0.16 75.2 0.080 0.32 865 UHE1C471MPD6

680 8×20 0.16 108.8 0.069 0.27 1050 UHE1C681MPD

680 10×16 0.16 108.8 0.060 0.24 1210 UHE1C681MPD6

1000 10×20 0.16 160 0.046 0.18 1400 UHE1C102MPD

1000 12.5×15 0.16 160 0.049 0.16 1450 UHE1C102MHD6

1200 10×25 0.16 192 0.042 0.17 1650 UHE1C122MPD

1500 10×31.5 0.16 240 0.031 0.12 1910 UHE1C152MPD

1500 12.5×20 0.16 240 0.035 0.12 1900 UHE1C152MHD6

1500 16×15 0.16 240 0.042 0.12 1940 UHE1C152MHD3

2200 12.5×25 0.18 352 0.027 0.089 2230 UHE1C222MHD

2200 18×15 0.18 352 0.043 0.11 2210 UHE1C222MHD6

2700 12.5×31.5 0.18 432 0.024 0.078 2650 UHE1C272MHD

2700 16×20 0.18 432 0.027 0.078 2530 UHE1C272MHD6

3300 12.5×35.5 0.20 528 0.020 0.065 2880 UHE1C332MHD

3900 12.5×40 0.20 624 0.017 0.056 3350 UHE1C392MHD

3900 16×25 0.20 624 0.021 0.060 2930 UHE1C392MHD6

3900 16×20 0.20 624 0.026 0.067 2860 UHE1C392MHD3

4700 16×31.5 0.22 752 0.017 0.050 3450 UHE1C472MHD

4700 18×25 0.22 752 0.019 0.049 3140 UHE1C472MHD6

5600 16×35.5 0.24 896 0.015 0.044 3610 UHE1C562MHD

5600 18×31.5 0.24 896 0.015 0.040 4170 UHE1C562MHD6

6800 16×40 0.26 1088 0.013 0.038 4080 UHE1C682MHD

8200 18×35.5 0.30 1312 0.014 0.038 4220 UHE1C822MHD

10000 18×40 0.34 1600 0.012 0.032 4280 UHE1C103MHD

25

（1E）

47 5×11 0.14 11.75

0.58

2.30 210 UHE1E470MDD

100 6.3×11 0.14 25 0.22 0.87 340 UHE1E101MED

220 8×11.5 0.14 55 0.13 0.52 640 UHE1E221MPD

330 8×15 0.14 82.5 0.087 0.35 840 UHE1E331MPD

330 10×12.5 0.14 82.5 0.080 0.32 865 UHE1E331MPD6

470 8×20 0.14 117.5 0.069 0.27 1050 UHE1E471MPD

470 10×16 0.14 117.5 0.060 0.24 1210 UHE1E471MPD6

680 10×20 0.14 170 0.046 0.18 1400 UHE1E681MPD

680 12.5×15 0.14 170 0.049 0.16 1450 UHE1E681MHD6

820 10×25 0.14 205 0.042 0.17 1650 UHE1E821MPD

1000 10×31.5 0.14 250 0.031 0.12 1910 UHE1E102MPD

1000 12.5×20 0.14 250 0.035 0.12 1900 UHE1E102MHD6

Dimensions

For cut leads, formed leads or taped parts, please add the appropriate code after the size code (12th digit ).
If there is no size code in the part number, please add size code “1” and then add the appropriate code.

UHE

Dimensions

Impedance（Ω）

）

100kHz

20℃/

MAX.

Leakage Current

Rated

Rated Voltage

（V）

（code）

6.3

（0J）

10

（1A）

For cut leads, formed leads or taped parts, please add the appropriate code after the size code (12th digit ).
If there is no size code in the part number, please add size code “1” and then add the appropriate code.

Capacitance

（µF）

150 5×11 0.22 9.45 0.58 2.30 210 UHE0J151MDD

330 6.3×11 0.22 20.79 0.22 0.87 340 UHE0J331MED

680 8×11.5 0.22 42.84 0.13 0.52 640 UHE0J681MPD

820 10×12.5 0.22 51.66 0.080 0.32 865 UHE0J821MPD

1000 8×15 0.22 63 0.087 0.35 840 UHE0J102MPD

1200 8×20 0.22 75.6 0.069 0.27 1050 UHE0J122MPD

1200 10×16 0.22 75.6 0.060 0.24 1210 UHE0J122MPD6

1500 10×20 0.22 94.5 0.046 0.18 1400 UHE0J152MPD

1800 12.5×15 0.22 113.4 0.049 0.16 1450 UHE0J182MHD

2200 10×25 0.24 138.6 0.042 0.17 1650 UHE0J222MPD

2700 10×31.5 0.24 170.1 0.031 0.12 1910 UHE0J272MPD6

2700 16×15 0.24 170.1 0.042 0.12 1940 UHE0J272MHD

3300 12.5×20 0.26 207.9 0.035 0.12 1900 UHE0J332MHD

3900 12.5×25 0.26 245.7 0.027 0.089 2230 UHE0J392MHD

3900 18×15 0.26 245.7 0.043 0.11 2210 UHE0J392MHD6

4700 12.5×31.5 0.28 296.1 0.024 0.078 2650 UHE0J472MHD

5600 12.5×35.5 0.30 352.8 0.020 0.065 2880 UHE0J562MHD

5600 16×20 0.30 352.8 0.027 0.078 2530 UHE0J562MHD6

6800 12.5×40 0.32 428.4 0.017 0.056 3350 UHE0J682MHD

6800 16×25 0.32 428.4 0.021 0.060 2930 UHE0J682MHD6

6800 18×20 0.32 428.4 0.026 0.067 2860 UHE0J682MHD3

8200 16×31.5 0.36 516.6 0.017 0.050 3450 UHE0J822MHD

10000 16×35.5 0.40 630 0.015 0.044 3610 UHE0J103MHD

10000 18×25 0.40 630 0.019 0.049 3140 UHE0J103MHD6

12000 16×40 0.44 756 0.013 0.038 4080 UHE0J123MHD

12000 18×31.5 0.44 756 0.015 0.040 4170 UHE0J123MHD6

15000 18×35.5 0.50 945 0.014 0.038 4220 UHE0J153MHD

18000 18×40 0.56 1134 0.012 0.032 4280 UHE0J183MHD

100 5×11 0.19 10 0.58 2.30 210 UHE1A101MDD

220 6.3×11 0.19 22 0.22 0.87 340 UHE1A221MED

470 8×11.5 0.19 47 0.13 0.52 640 UHE1A471MPD

680 8×15 0.19 68 0.087 0.35 840 UHE1A681MPD

680 10×12.5 0.19 68 0.080 0.32 865 UHE1A681MPD6

1000 8×20 0.19 100 0.069 0.27 1050 UHE1A102MPD

1000 10×16 0.19 100 0.060 0.24 1210 UHE1A102MPD6

1200 10×20 0.19 120 0.046 0.18 1400 UHE1A122MPD

1500 10×25 0.19 150 0.042 0.17 1650

1500 12.5×15 0.19 150 0.049 0.16 1450 UHE1A152MHD6

2200 10×31.5 0.21 220 0.031 0.12 1910 UHE1A222MPD

2200 12.5×20 0.21 220 0.035 0.12 1900 UHE1A222MHD6

2200 16×15 0.21 220 0.042 0.12 1940 UHE1A222MHD3

2700 18×15 0.21 270 0.043 0.11 2210 UHE1A272MHD

3300 12.5×25 0.23 330 0.027 0.089 2230 UHE1A332MHD

3900 12.5×31.5 0.23 390 0.024 0.078 2650 UHE1A392MHD

3900 16×20 0.23 390 0.027 0.078 2530 UHE1A392MHD6

4700 12.5×35.5 0.25 470 0.020 0.065 2880 UHE1A472MHD

5600 12.5×40 0.27 560 0.017 0.056 3350 UHE1A562MHD

5600 16×25 0.27 560 0.021 0.060 2930 UHE1A562MHD6

Case Size

φD×L（mm）

tan δ

（µA）

at 20℃ after

2 minutes

（

Rated Ripple

（mArms）

－10℃/
100kHz

（105℃/100kHz）

Part Number

UHE1A152MPD

CAT.8100K

ALUMINUM ELECTROLYTIC CAPACITORS

UHE

Dimensions

Impedance（Ω）

20℃/

）

100kHz

MAX.

Rated Voltage

（V）

（code）

10

（1A）

16

（1C）

25

（1E）

For cut leads, formed leads or taped parts, please add the appropriate code after the size code (12th digit ).
If there is no size code in the part number, please add size code “1” and then add the appropriate code.

Rated

Capacitance

（µF）

5600 18×20 0.27 560 0.026 0.067 2860 UHE1A562MHD3

6800 16×31.5 0.29 680 0.017 0.050 3450 UHE1A682MHD

6800 18×25 0.29 680 0.019 0.049 3140 UHE1A682MHD6

8200 16×35.5 0.33 820 0.015 0.044 3610 UHE1A822MHD

8200 18×31.5 0.33 820 0.015 0.040 4170 UHE1A822MHD6

10000 16×40 0.37 1000 0.013 0.038 4080 UHE1A103MHD

10000 18×35.5 0.37 1000 0.014 0.038 4220 UHE1A103MHD6

12000 18×40 0.41 1200 0.012 0.032 4280 UHE1A123MHD

56 5×11 0.16 8.96 0.58 2.30 210 UHE1C560MDD

120 6.3×11 0.16 19.2 0.22 0.87 340 UHE1C121MED

330 8×11.5 0.16 52.8 0.13 0.52 640 UHE1C331MPD

470 8×15 0.16 75.2 0.087 0.35 840 UHE1C471MPD

470 10×12.5 0.16 75.2 0.080 0.32 865 UHE1C471MPD6

680 8×20 0.16 108.8 0.069 0.27 1050 UHE1C681MPD

680 10×16 0.16 108.8 0.060 0.24 1210 UHE1C681MPD6

1000 10×20 0.16 160 0.046 0.18 1400 UHE1C102MPD

1000 12.5×15 0.16 160 0.049 0.16 1450 UHE1C102MHD6

1200 10×25 0.16 192 0.042 0.17 1650 UHE1C122MPD

1500 10×31.5 0.16 240 0.031 0.12 1910 UHE1C152MPD

1500 12.5×20 0.16 240 0.035 0.12 1900 UHE1C152MHD6

1500 16×15 0.16 240 0.042 0.12 1940 UHE1C152MHD3

2200 12.5×25 0.18 352 0.027 0.089 2230 UHE1C222MHD

2200 18×15 0.18 352 0.043 0.11 2210 UHE1C222MHD6

2700 12.5×31.5 0.18 432 0.024 0.078 2650 UHE1C272MHD

2700 16×20 0.18 432 0.027 0.078 2530 UHE1C272MHD6

3300 12.5×35.5 0.20 528 0.020 0.065 2880 UHE1C332MHD

3900 12.5×40 0.20 624 0.017 0.056 3350 UHE1C392MHD

3900 16×25 0.20 624 0.021 0.060 2930 UHE1C392MHD6

3900 16×20 0.20 624 0.026 0.067 2860 UHE1C392MHD3

4700 16×31.5 0.22 752 0.017 0.050 3450 UHE1C472MHD

4700 18×25 0.22 752 0.019 0.049 3140 UHE1C472MHD6

5600 16×35.5 0.24 896 0.015 0.044 3610 UHE1C562MHD

5600 18×31.5 0.24 896 0.015 0.040 4170 UHE1C562MHD6

6800 16×40 0.26 1088 0.013 0.038 4080 UHE1C682MHD

8200 18×35.5 0.30 1312 0.014 0.038 4220 UHE1C822MHD

10000 18×40 0.34 1600 0.012 0.032 4280 UHE1C103MHD

47 5×11 0.14 11.75 0.58

100 6.3×11 0.14 25 0.22 0.87 340 UHE1E101MED

220 8×11.5 0.14 55 0.13 0.52 640 UHE1E221MPD

330 8×15 0.14 82.5 0.087 0.35 840 UHE1E331MPD

330 10×12.5 0.14 82.5 0.080 0.32 865 UHE1E331MPD6

470 8×20 0.14 117.5 0.069 0.27 1050 UHE1E471MPD

470 10×16 0.14 117.5 0.060 0.24 1210 UHE1E471MPD6

680 10×20 0.14 170 0.046 0.18 1400 UHE1E681MPD

680 12.5×15 0.14 170 0.049 0.16 1450 UHE1E681MHD6

820 10×25 0.14 205 0.042 0.17 1650 UHE1E821MPD

1000 10×31.5 0.14 250 0.031 0.12 1910 UHE1E102MPD

1000 12.5×20 0.14 250 0.035 0.12 1900 UHE1E102MHD6

Case Size

φD×L（mm）

tan δ

Leakage Current

（µA）

at 20℃ after

2 minutes

（

Rated Ripple

－10℃/
100kHz

2.30 210 UHE1E470MDD

（mArms）

（105℃/100kHz）

Part Number

CAT.8100K

ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS

UHE

Rated Voltage

（V）

（code）

Rated

Capacitance

（µF）

Case Size

φD×L（mm）

tan δ

Leakage Current

（µA）

Impedance（Ω）

MAX.

Rated Ripple

（mArms）

（105℃/100kHz）

Part Number

（

at 20℃ after

2 minutes

）

20℃/

100kHz

－10℃/
100kHz

50

（1H）

4.7 5×11 0.10 3 1.90 7.60 88 UHE1H4R7MDD

10 5×11 0.10 5 1.50 6.00 100 UHE1H100MDD

22 5×11 0.10 11 0.70 2.80 180 UHE1H220MDD

33 6.3×11 0.10 16.5 0.30 1.20 295 UHE1H330MED

47 6.3×11 0.10 23.5 0.30 1.20 295 UHE1H470MED

56 6.3×11 0.10 28 0.30 1.20 295 UHE1H560MED

100 8×11.5 0.10 50 0.17 0.68 555 UHE1H101MPD

120 8×15 0.10 60 0.12 0.48 730 UHE1H121MPD

150 10× 12.5 0.10 75 0.12 0.48 760 UHE1H151MPD

180 8×20 0.10 90 0.091 0.36 910 UHE1H181MPD

220 10× 16 0.10 110 0.084 0.34 1050 UHE1H221MPD

270 10× 20 0.10 135 0.060 0.24 1220 UHE1H271MPD

270 12.5× 15 0.10 135 0.061 0.20 1260 UHE1H271MHD6

330 10× 25 0.10 165 0.055 0.22 1440 UHE1H331MPD

330 10× 20 0.10 165 0.060 0.24 1220 UHE1H331MPD6

470 10× 31.5 0.10 235 0.043 0.17 1690 UHE1H471MPD

470 12.5× 20 0.10 235 0.045 0.15 1660 UHE1H471MHD6

470 16× 15 0.10 235 0.055 0.17 1690 UHE1H471MHD3

560 12.5× 25 0.10 280 0.034 0.11 1950 UHE1H561MHD

560 18× 15 0.10 280 0.054 0.15 1930 UHE1H561MHD6

680 12.5× 31.5 0.10 340 0.030 0.10 2310 UHE1H681MHD

820 12.5× 35.5 0.10 410 0.025 0.083 2510 UHE1H821MHD

820 16× 20 0.10 410 0.034 0.10 2210 UHE1H821MHD6

1000 12.5× 40 0.10 500 0.021 0.069 2920 UHE1H102MHD

1000 16× 25 0.10 500 0.025 0.075 2555 UHE1H102MHD6

1000 18× 20 0.10 500 0.036 0.097 2490 UHE1H102MHD3

1200 16× 31.5 0.10 600 0.022 0.066 3010 UHE1H122MHD

1200 18× 25 0.10 600 0.026 0.070 2740 UHE1H122MHD6

1500 16× 35.5 0.10 750 0.019 0.057 3150 UHE1H152MHD

1800 16× 40 0.10 900 0.016 0.048 3710 UHE1H182MHD

1800 18× 31.5 0.10 900 0.021 0.057 3635 UHE1H182MHD6

2200 18× 35.5 0.12 1100 0.017 0.046 3680 UHE1H222MHD6

2700 18× 40 0.12 1350 0.014 0.038 3800 UHE1H272MHD

63

（1J）

15 5×11 0.09 9.45 2.30 9.30 62 UHE1J150MDD

33 6.3×11 0.09 20.79 1.20 5.00 126 UHE1J330MED

47 8×11.5 0.09 29.61 0.63 2.80 260 UHE1J470MPD

56 8×11.5 0.09 35.28 0.63 2.80

260

UHE1J560MPD

82 8×15 0.09 51.66 0.45 2.10 335 UHE1J820MPD

82 10× 12.5 0.09 51.66 0.43 1.80 325 UHE1J820MPD6

120 8×20 0.09 75.6 0.33 1.60 408 UHE1J121MPD

120 10× 16 0.09 75.6 0.31 1.50 400 UHE1J121MPD6

180 10× 20 0.09 113.4 0.21 0.94 518 UHE1J181MPD

180 12.5× 15 0.09 113.4 0.23 1.10 527 UHE1J181MHD6

220 10× 25 0.09 138.6 0.20 0.84 595 UHE1J221MPD

270 10× 31.5 0.09 170.1 0.15 0.71 740 UHE1J271MPD

270 12.5× 20 0.09 170.1 0.16 0.64 765 UHE1J271MHD6

270 16× 15 0.09 170.1 0.14 0.66 895 UHE1J271MHD3

330 12.5× 25 0.09 207.9 0.12 0.45 875 UHE1J331MHD

Dimensions

For cut leads, formed leads or taped parts, please add the appropriate code after the size code (12th digit ).
If there is no size code in the part number, please add size code “1” and then add the appropriate code.

UHE

Dimensions

Impedance（Ω）

）

20℃/

100kHz

MAX.

Leakage Current

Rated

Rated Voltage

（V）

（code）

25

（1E）

35

（1V）

50

（1H）

For cut leads, formed leads or taped parts, please add the appropriate code after the size code (12th digit ).
If there is no size code in the part number, please add size code “1” and then add the appropriate code.

Capacitance

（µF）

1000 16×15 0.14 250 0.042 0.12 1940 UHE1E102MHD3

1200 18×15 0.14 300 0.043 0.11 2210 UHE1E122MHD

1500 12.5×25 0.14 375 0.027 0.089 2230 UHE1E152MHD

1800 12.5×31.5 0.14 450 0.024 0.078 2650 UHE1E182MHD

1800 16×20 0.14 450 0.027 0.078 2530 UHE1E182MHD6

2200 12.5×35.5 0.16 550 0.020 0.065 2880 UHE1E222MHD

2200 18×20 0.16 550 0.026 0.067 2860 UHE1E222MHD6

2700 12.5×40 0.16 675 0.017 0.056 3350 UHE1E272MHD

2700 16×25 0.16 675 0.021 0.060 2930 UHE1E272MHD6

3300 16×31.5 0.18 825 0.017 0.050 3450 UHE1E332MHD

3300 18×25 0.18 825 0.019 0.049 3140 UHE1E332MHD6

3900 16×35.5 0.18 975 0.015 0.044 3610 UHE1E392MHD

3900 18×31.5 0.18 975 0.015 0.040 4170 UHE1E392MHD6

4700 16×40 0.20 1175 0.013 0.038 4080 UHE1E472MHD

4700 18×35.5 0.20 1175 0.014 0.038 4220 UHE1E472MHD6

5600 18×40 0.22 1400 0.012 0.032 4280 UHE1E562MHD

33 5×11 0.12 11.55 0.58 2.30 210 UHE1V330MDD

47 6.3×11 0.12 16.45 0.22 0.87 250 UHE1V470MED

56 6.3×11 0.12 19.6 0.22 0.87 340 UHE1V560MED

100 8×11.5 0.12 35 0.13 0.52 640 UHE1V101MPD

150 8×11.5 0.12 52.5 0.13 0.52 640 UHE1V151MPD

220 8×15 0.12 77 0.087 0.35 840 UHE1V221MPD

220 10×12.5 0.12 77 0.080 0.32 865 UHE1V221MPD6

270 8×20 0.12 94.5 0.069 0.27 1050 UHE1V271MPD

330 10×16 0.12 115.5 0.060 0.24 1210 UHE1V331MPD

470 10×20 0.12 164.5 0.046 0.18 1400 UHE1V471MPD

470 12.5×15 0.12 164.5 0.049 0.16 1450 UHE1V471MHD6

560 10×25 0.12 196 0.042 0.17 1650 UHE1V561MPD

680 10×31.5 0.12 238 0.031 0.12 1910 UHE1V681MPD

680 12.5×20 0.12 238 0.035 0.12 1900 UHE1V681MHD6

680 16×15 0.12 238 0.042 0.12 1940 UHE1V681MHD3

1000 12.5×25 0.12 350 0.027 0.089 2230 UHE1V102MHD

1000 18×15 0.12 350 0.043 0.11 2210 UHE1V102MHD6

1200 12.5×31.5 0.12 420 0.024 0.078 2650 UHE1V122MHD

1200 16×20 0.12 420 0.027 0.078 2530 UHE1V122MHD6

1500 12.5×35.5 0.12 525 0.020 0.065 2880 UHE1V152MHD

1800 12.5×40 0.12 630 0.017 0.056 3350

1800 16×25 0.12 630 0.021 0.060 2930 UHE1V182MHD6

1800 18×20 0.12 630 0.026 0.067 2860 UHE1V182MHD3

2200 16×31.5 0.14 770 0.017 0.050 3450 UHE1V222MHD

2200 18×25 0.14 770 0.019 0.049 3140 UHE1V222MHD6

2700 16×35.5 0.14 945 0.015 0.044 3610 UHE1V272MHD

2700 18×31.5 0.14 945 0.015 0.040 4170 UHE1V272MHD6

3300 16×40 0.16 1155 0.013 0.038 4080 UHE1V332MHD

3300 18×35.5 0.16 1155 0.014 0.038 4220 UHE1V332MHD6

3900 18×40 0.16 1365 0.012 0.032 4280 UHE1V392MHD

2.2 5×11 0.10 3 2.50 10.00 43 UHE1H2R2MDD

3.3 5×11 0.10 3 2.20 8.80 53 UHE1H3R3MDD

Case Size

φD×L（mm）

tan δ

（µA）

at 20℃ after

2 minutes

（

－10℃/
100kHz

Rated Ripple

（mArms）

（105℃/100kHz）

Part Number

UHE1V182MHD

CAT.8100K

ALUMINUM ELECTROLYTIC CAPACITORS

UHE

Dimensions

Impedance（Ω）

20℃/

）

100kHz

MAX.

Rated Voltage

（V）

（code）

50

（1H）

63

（1J）

For cut leads, formed leads or taped parts, please add the appropriate code after the size code (12th digit ).
If there is no size code in the part number, please add size code “1” and then add the appropriate code.

Rated

Capacitance

（µF）

4.7 5×11 0.10 3 1.90 7.60 88 UHE1H4R7MDD

10 5×11 0.10 5 1.50 6.00 100 UHE1H100MDD

22 5×11 0.10 11 0.70 2.80 180 UHE1H220MDD

33 6.3×11 0.10 16.5 0.30 1.20 295 UHE1H330MED

47 6.3×11 0.10 23.5 0.30 1.20 295 UHE1H470MED

56 6.3×11 0.10 28 0.30 1.20 295 UHE1H560MED

100 8×11.5 0.10 50 0.17 0.68 555 UHE1H101MPD

120 8×15 0.10 60 0.12 0.48 730 UHE1H121MPD

150 10× 12.5 0.10 75 0.12 0.48 760 UHE1H151MPD

180 8×20 0.10 90 0.091 0.36 910 UHE1H181MPD

220 10× 16 0.10 110 0.084 0.34 1050 UHE1H221MPD

270 10× 20 0.10 135 0.060 0.24 1220 UHE1H271MPD

270 12.5× 15 0.10 135 0.061 0.20 1260 UHE1H271MHD6

330 10× 25 0.10 165 0.055 0.22 1440 UHE1H331MPD

330 10× 20 0.10 165 0.060 0.24 1220 UHE1H331MPD6

470 10× 31.5 0.10 235 0.043 0.17 1690 UHE1H471MPD

470 12.5× 20 0.10 235 0.045 0.15 1660 UHE1H471MHD6

470 16× 15 0.10 235 0.055 0.17 1690 UHE1H471MHD3

560 12.5× 25 0.10 280 0.034 0.11 1950 UHE1H561MHD

560 18× 15 0.10 280 0.054 0.15 1930 UHE1H561MHD6

680 12.5× 31.5 0.10 340 0.030 0.10 2310 UHE1H681MHD

820 12.5× 35.5 0.10 410 0.025 0.083 2510 UHE1H821MHD

820 16× 20 0.10 410 0.034 0.10 2210 UHE1H821MHD6

1000 12.5× 40 0.10 500 0.021 0.069 2920 UHE1H102MHD

1000 16× 25 0.10 500 0.025 0.075 2555 UHE1H102MHD6

1000 18× 20 0.10 500 0.036 0.097 2490 UHE1H102MHD3

1200 16× 31.5 0.10 600 0.022 0.066 3010 UHE1H122MHD

1200 18× 25 0.10 600 0.026 0.070 2740 UHE1H122MHD6

1500 16× 35.5 0.10 750 0.019 0.057 3150 UHE1H152MHD

1800 16× 40 0.10 900 0.016 0.048 3710 UHE1H182MHD

1800 18× 31.5 0.10 900 0.021 0.057 3635 UHE1H182MHD6

2200 18× 35.5 0.12 1100 0.017 0.046 3680 UHE1H222MHD6

2700 18× 40 0.12 1350 0.014 0.038 3800 UHE1H272MHD

15 5×11 0.09 9.45 2.30 9.30 62 UHE1J150MDD

33 6.3×11 0.09 20.79 1.20 5.00 126 UHE1J330MED

47 8×11.5 0.09 29.61 0.63 2.80 260 UHE1J470MPD

56 8×11.5 0.09 35.28 0.63 2.80 260

82 8×15 0.09 51.66 0.45 2.10 335 UHE1J820MPD

82 10× 12.5 0.09 51.66 0.43 1.80 325 UHE1J820MPD6

120 8×20 0.09 75.6 0.33 1.60 408 UHE1J121MPD

120 10× 16 0.09 75.6 0.31 1.50 400 UHE1J121MPD6

180 10× 20 0.09 113.4 0.21 0.94 518 UHE1J181MPD

180 12.5× 15 0.09 113.4 0.23 1.10 527 UHE1J181MHD6

220 10× 25 0.09 138.6 0.20 0.84 595 UHE1J221MPD

270 10× 31.5 0.09 170.1 0.15 0.71 740 UHE1J271MPD

270 12.5× 20 0.09 170.1 0.16 0.64 765 UHE1J271MHD6

270 16× 15 0.09 170.1 0.14 0.66 895 UHE1J271MHD3

330 12.5× 25 0.09 207.9 0.12 0.45 875 UHE1J331MHD

Case Size

φD×L（mm）

tan δ

Leakage Current

（µA）

at 20℃ after

2 minutes

（

－10℃/
100kHz

Rated Ripple

（mArms）

（105℃/100kHz）

Part Number

UHE1J560MPD

CAT.8100K

ALUMINUM ELECTROLYTIC CAPACITORS

ALUMINUM ELECTROLYTIC CAPACITORS

µ

(L < 20) 1.5
(L 20) 2.0

(mm)

φD

P

φd

10

5.0

0.6

5

2.0

0.5

12.5

5.0167.5

0.6 0.8

18

7.5

0.8

6.3

2.5

0.5 0.6

8

3.5

In case L > 25 for the φ12.5 dia. unit, lead dia. φd = 0.8mm

φ D

5

Pb-free leadwire
Pb-free PET sleeve

DD

6.3 ED

8 · 10 PD

12.5 to 18 HD

Configuration

Pressure

relief vent

(φ6.3up)

UHW

UHV

Long Life

Lower impedance at high frequency range.
Smaller case size and high ripple current.
Compliant to the RoHS directive (2011/65/EU,(EU)2015/863).

Specifications

Radial Lead Type

Type numbering system (Example : 16V 2200µF)

Smaller

Frequency coefficient of rated ripple current

120Hz 1kHz 10kHz 10kHz or more

Cap. (µF)

Frequency

8.2 to 33
39 to 180
220 to 560
680 to 1800
2200 to 3900
4700 to 15000

0.70

0.75

0.85

0.87

0.90

0.95

0.40

0.40

0.50

0.60

0.75

0.85

0.90

0.90

0.94

0.95

0.95

0.98

1.00

1.00

1.00

1.00

1.00

1.00

UHW

Miniature Sized, High Ripple Current,
High Reliability

Performance Characteristics

ltem

0.21 0.18 0.15 0.13 0.11 0.10 0.09 0.09 0.08

Category

Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Leakage Current

Tangent of loss angle (tan

δ

)

Stability at Low Temperature

Endurance

–40 to +105˚C

6.3 to 100V

8.2 to 15000µF

± 20% at 120Hz, 20˚C

After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV (µA)

Rated voltage (V)

Case size

φD

<

=

6.3 8×11.5 8×15 , 8×20 φD

>
=

10

tan

δ

(MAX.)

For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF.

Z–25˚C / Z+20˚C

6.3V

6000 hours 8000 hours 9000 hours 10000 hours

8000 hours

7000 hours

10000 hours

9000 hours

11000 hours 12000 hours

10000 hours 10000 hours

63 to 100V

10 to 50V

Rated voltage

(V)

6.3 10 16 25 35 50 63 80 100

The following specifications shall be met when the capacitors are restored to 20˚C after D.C. bias plus rated ripple current is
applied at 105

˚C

, the peak voltage shall not exceed the rated voltage.

Marking

Printed with white color letter on black sleeve.

Capacitance change Within ± 25% of the initial capacitance value（

6.3V 10V：± 30%

）

tan δ 200% or less than the initial specified value

Leakage current Less than or equal to the initial specified value

120Hz

20˚C

120Hz

2 2 2 2 2 2 2 2 2

3 3 3 3 3 3

3 3 3

6.3 10 16 25 35 50 63 80 100

5 5 4 4 4 4

Z–40˚C /

Z+20˚C

φD

<
=

6.3

φ

>
=

8

Rated voltage (V)

Impedance ratio

(MAX.)

Dimension table in next page.

UHE

Please refer to the Guidelines for Aluminum Electrolytic Capacitors

for end seal configuration information.

UHE

Dimensions

Rated Voltage

（V）

（code）

Capacitance

63

（1J）

100

（2A）

For cut leads, formed leads or taped parts, please add the appropriate code after the size code (12th digit ).
If there is no size code in the part number, please add size code “1” and then add the appropriate code.

For formed lead or taped product specifications and minimum order quantity,

please refer to the Guidelines for Aluminum Electrolytic Capacitors.

Rated

（µF）

390 18× 15 0.09 245.7 0.12 0.50 1030 UHE1J391MHD

470 12.5× 31.5 0.09 296.1 0.10 0.42 1010 UHE1J471MHD

470 16× 20 0.09 296.1 0.091 0.38 1130 UHE1J471MHD6

560 12.5× 35.5 0.09 352.8 0.083 0.35 1140 UHE1J561MHD

560 16× 25 0.09 352.8 0.073 0.27 1350 UHE1J561MHD6

680 12.5× 40 0.09 428.4 0.071 0.30 1280 UHE1J681MHD

680 18× 20 0.09 428.4 0.080 0.30 1300 UHE1J681MHD6

820 16× 31.5 0.09 516.6 0.054 0.20 1650 UHE1J821MHD

820 18× 25 0.09 516.6 0.057 0.21 1560 UHE1J821MHD6

1000 16× 35.5 0.09 630 0.045 0.17 1900 UHE1J102MHD

1000 18× 31.5 0.09 630 0.047 0.17 1720 UHE1J102MHD6

1200 16× 40 0.09 756 0.040 0.15 2130 UHE1J122MHD

1200 18× 35.5 0.09 756 0.040 0.15 1890 UHE1J122MHD6

1500 18× 40 0.09 945 0.036 0.13 2470 UHE1J152MHD

6.8 5×11 0.08 6.8 2.30 9.30 62 UHE2A6R8MDD

15 6.3×11 0.08 15 1.20 5.00 126 UHE2A150MED

27 8×11.5 0.08 27 0.63 2.80 260 UHE2A270MPD

39 8×15 0.08 39 0.45 2.10 335 UHE2A390MPD

47 10× 12.5 0.08 47 0.43 1.80 325 UHE2A470MPD

56 8×20 0.08 56 0.33 1.60 408 UHE2A560MPD

68 10× 16 0.08 68 0.31 1.50 400 UHE2A680MPD

82 10× 20 0.08 82 0.21 0.94 518 UHE2A820MPD

82 12.5× 15 0.08 82 0.23 1.10 527 UHE2A820MHD6

100 10× 25 0.08 100 0.20 0.84 595 UHE2A101MPD

100 12.5× 20 0.08 100 0.20 0.84 740 UHE2A101MHD6

120 10× 31.5 0.08 120 0.15 0.71 740 UHE2A121MPD

120 12.5× 20 0.08 120 0.16 0.64 765 UHE2A121MHD6

150 16× 15 0.08 150 0.14 0.66 895 UHE2A151MHD

180 12.5× 25 0.08 180 0.12 0.45 875 UHE2A181MHD

180 18× 15 0.08 180 0.12 0.50 1030 UHE2A181MHD6

220 12.5× 31.5 0.08 220 0.10 0.42 1010 UHE2A221MHD

220 16× 20 0.08 220 0.091 0.38 1130 UHE2A221MHD6

270 12.5× 35.5 0.08 270 0.083 0.35 1140 UHE2A271MHD

270 16× 25 0.08 270 0.073 0.27 1350 UHE2A271MHD6

330 12.5× 40 0.08 330 0.071 0.30 1280 UHE2A331MHD

330 18× 20 0.08 330 0.080 0.30 1300 UHE2A331MHD6

390 16× 31.5 0.08 390 0.054 0.20 1650

390 18× 25 0.08 390 0.057 0.21 1560 UHE2A391MHD6

470 16× 35.5 0.08 470 0.045 0.17 1900 UHE2A471MHD

470 18× 31.5 0.08 470 0.047 0.17 1720 UHE2A471MHD6

560 16× 40 0.08 560 0.040 0.15 2130 UHE2A561MHD

680 18× 35.5 0.08 680 0.040 0.15 1890 UHE2A681MHD

820 18× 40 0.08 820 0.036 0.13 2470 UHE2A821MHD

Case Size

φD×L（mm）

Leakage Current

tan δ

（µA）

at 20℃ after

2 minutes

（

20℃/

）

100kHz

Impedance（Ω）

MAX.

－10℃/
100kHz

（105℃/100kHz）

Rated Ripple

（mArms）

Part Number

UHE2A391MHD

CAT.8100K