Datasheet UGN3055U Datasheet (Allegro)

3055

MULTIPLEXED
TWO-WIRE HALL EFFECT
SENSOR IC

3055

Data Sheet

27680

DISCONTINUED PRODUCT

Shown for Reference Only

X

LOGIC

1

BUS

32

GROUND

SWITCH IN

Dwg. PH-005

MULTIPLEXED TWO-WIRE

HALL-EFFECT SENSOR ICs

The UGN3055U Hall-effect sensor is a digital magnetic sensing IC
capable of communicating over a two-wire power/signal bus. Using a
sequential addressing scheme, the device responds to a signal on the
bus and returns the diagnostic status of the IC, as well as the status of
each monitored external magnetic field. As many as 30 sensors can
function on the same two-wire bus. This IC is ideal for multiple sensor
applications where minimizing the wiring harness size is desirable or
essential.

The device consists of high-resolution bipolar Hall-effect switching
circuitry, the output of which drives high-density CMOS logic stages.
These logic stages decode the address pulse and enable a response
at the appropriate address. The combination of magnetic-field or
switch-status sensing, low-noise amplification of the Hall-transducer
output, and high-density decoding and control logic is made possible
by the development of a new sensor BiMOS fabrication technology.

This unique magnetic sensing IC operates within specifications
between -20°C and +85°C. Alternate magnetic and temperature
specifications are available upon request. It is supplied in a 60 mil
(1.54 mm) thick, three-pin plastic SIP. Each package is clearly marked
with a two-digit decimal device address (xx).

Pinning is shown viewed from branded side.

ABSOLUTE MAXIMUM RATINGS

at T

= +25°C

A

Supply Voltage, V

Magnetic Flux Density, B............ Unlimited

Operating Temperature Range,

T

.......................... -20°C to +85°C

A

Storage Temperature Range,

.............................. -55°C to +150°C

T

S

Package Power Dissipation,

P

.................................... 750 mW

D

........................... 24 V

BUS

FEATURES

■ Complete Multiplexed Hall-Effect IC with

Simple Sequential Addressing Protocol

■ Allows Power and Communication Over a

Two-Wire Bus (Supply/Signal and Ground)

■ Up to 30 Hall-Effect Sensors Can Share a Bus

■ Sensor Diagnostic Capabilities

■ Magnetic-Field or Switch-Status Sensing

■ Low Power of BiMOS Technology Favors

Battery-Powered and Mobile Applications

■ Ideal for Automotive, Consumer, and Industrial Applications

Always order by complete part number: UGN3055U .

3055

MULTIPLEXED
TWO-WIRE HALL EFFECT
SENSOR IC

OPERATIONAL CHARACTERISTIC over operating temperature range.

Electrical Limits
Characteristics

Power Supply Voltage V
Signal Current I
Quiescent Current V

= 6 V I

BUS

= 9 V I

V

BUS

I

QH–IQL

Address Range Addr 1 — 30 —
Clock Thresholds LOW to HIGH V

HIGH to LOW V

Hysteresis V
Clock Period t
Address LOW Voltage V
Address HIGH Voltage V
Power-On Reset Voltage V
Settling Time V

= 9 V t

BUS

= 6 V t

V

BUS

Propagation Delay LOW to HIGH t

HIGH to LOW t

Pin 3 Input Resistance No Magnetic Field (V

Mag. Field Present (V

= HIGH) R

OUT

= LOW) R

OUT

Magnetic Characteristics

Magnetic Thresholds *Turn-On B

Turn-Off B

Hysteresis (B

*Alternate magnetic switch point specifications are available on request. Please contact the factory.

)B

OP–BRP

Symbol Min. Typ. Max. Units

BUS

S

QH

QL

I

Q

CLH

CHL

CHYS

CLK

L

H

RST

h

l

plh

phl

OUTH

OUTL

OP

RP

HYS

——15V
12 15 20 mA
— — 2.5 mA
— — 2.5 mA
— — 300 µA

— — 8.5 V

6.5 — — V
— 0.8 — V

0.1 1.0 — ms

V

RST

V

CLH

6V
9V

CHL

BUS

2.5 3.5 5.5 V

100 — — µs
100 — — µs

10 — — µs
——10µs
40 — 75 kΩ
——50Ω

50 150 300 G

-25 100 300 G

05075G

V
V

115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 [phone]

W
Copyright © 1988, 1991, Allegro MicroSystems, Inc.

3055

A

MULTIPLEXED
TWO-WIRE HALL EFFECT
SENSOR IC

(±0.005” [0.13 mm] die placement)

ACTIVE AREA DEPTH

0.015"

0.38 mm

NOM

0.071"

1.80 mm

0.084"

2.13 mm

FUNCTIONAL BLOCK DIAGRAMSENSOR LOCATION

1

BUS

REG

COMP COMP

CLOCK

CMOS LOGIC

RESET

SWITCH IN

3

(OPTIONAL)

BRANDED
SURFACE

1 32

Dwg. MH-002A

DEFINITION OF TERMS

Sensor Address

Each bus sensor has a factory-specified predefined
address. At present, allowable sensor addresses are
integers from 1 to 30.

LOW-to-HlGH Clock Threshold (V

Minimum voltage required during the positive-going
transition to increment the bus address and trigger a
diagnostic response from the bus sensors. This is also
the maximum threshold of the on-chip comparator, which
monitors the supply voltage, V

BUS

HlGH-to-LOW Threshold (VHL)

Maximum voltage required during the negative-going
transition to trigger a

signal

current response from the bus
sensors. This is also the maximum threshold of the on­chip comparator, which monitors the supply voltage, V

Bus HIGH Voltage (VH)

Bus HIGH voltage required for addressing. Voltage
should be greater than V

CLH

.

Address LOW Voltage (VL)

Bus LOW Voltage required for addressing. Voltage
should be greater than V

Bus Reset Voltage (V

and less than V

RST

)

RST

Voltage level required to reset individual sensors.

Sensor Quiescent Current Drain (IQ)

The current drain of bus sensors when active but not
addressed. IQH is the maximum quiescent current drain
when the sensor is not addressed and is at VH. IQL is the
maximum quiescent current drain when the sensor is not
addressed and is at VL.

)

CLH

.

BUS.

.

CHL

GROUND

2

Dwg. FH-009

Diagnostic Phase

Period on the bus when the address voltage is at VH.
During this period, a correctly addressed sensor responds
by increasing its current drain on the bus. This response
from the sensor is called the diagnostic response and
the bus current

increase

is called the diagnostic current.

Signal Phase

Period on the bus when the address voltage is at VL. During
this period, a correctly addressed sensor that detects a
magnetic field greater than magnetic Operate Point, BOP,
responds by maintaining a current drain of IS on the bus.
This response from the sensor is called the signal response
and the bus current

increase

is called the signal current.

Sensor Address Response Current (IS)

Current returned by the bus sensors during the
the

signal

responses of the bus sensors. This is accomplished

diagnostic

and

by enabling the constant current source (CCS).

Magnetic Operate Point (BOP)

Minimum magnetic field required to switch ON the Hall
amplifier and switching circuitry of the addressed sensor.
This circuitry is only active when the sensor is addressed.

Magnetic Release Point (BRP)

Magnetic field required to switch OFF the Hall amplifier
and switching circuitry after the output has switched ON.
This is due to magnetic memory in the switching circuitry.
However, when a device is deactivated by changing the
current bus address, all magnetic memory is lost.

Magnetic Hysteresis (B

HYS

)

Difference between the BOP and BRP magnetic field thresh­olds.

3055

MULTIPLEXED
TWO-WIRE HALL EFFECT
SENSOR IC

ADDRESSING PROTOCOL

The device may be addressed by modulating
the supply voltage as shown in Figure 1. A
preferred addressing protocol is as follows:
the bus supply voltage is brought down to 0 V
so that all devices on the bus may be reset.
The voltage is then raised to the address
LOW voltage (VL) and the bus quiescent
current is measured. The bus is then toggled
between VL and VH (address HIGH voltage),
with each positive transition representing an
increment in the bus address. After each
voltage transition, the bus current is moni­tored to check for diagnostic and signal
responses from sensor ICs.

Sensor Addressing

When a sensor detects a bus address equal
to its factory programmed address, it re-

FIGURE 1

BUS TIMING D1

V

H

V

CLH

V

CHL

BUS

VOLTAGE

V

L

V

RST

0

RESET

DIAGNOSTIC
ADDRESS 01

DIAGNOSTIC
ADDRESS 02

t

plh

sponds with an increase in its supply current drain (called IS during the
HIGH portion of the address cycle). This response may be used as an
indication that the sensor is alive and well on the bus and is also called
the

diagnostic

response. If the sensor detects an ambient magnetic
field, it also responds with IS during the low portion of the address
cycle. This response from the sensor is called the

signal

response.
When the next positive transition is detected, the sensor becomes
disabled, and its contribution to the bus signal current returns to IQ.

Bus Current

Figure 1 displays the above described addressing protocol. The top
trace represents the bus voltage transitions as controlled by the bus
driver (see applications note for an optimal bus driver schematic). The
second trace represents the bus current contribution of sensor (ad­dress 02). The
detected its address on the bus; however, no

diagnostic

response from the sensor indicates that it

signal

response current
is returned, which indicates that sufficient magnetic field is not de­tected at the chip surface. The third trace represents the current drain
of sensor 03 when a magnetic field is detected. Note both the

nostic

and

signal

response from the sensor. The last trace represents

DIAGNOSTIC
ADDRESS 03

t

phl

DIAGNOSTIC
ADDRESS 04

DIAGNOSTIC

ADDRESS

n

RESET

DIAGNOSTIC

ADDRESS 01

diag-

SENSOR 02

CURRENT

WITH NO

MAGNETIC

FIELD

SENSOR 03

CURRENT

WITH

MAGNETIC

FIELD

TOTAL

BUS CURRENT

WITH

MAGNETIC

FIELD AT

SENSOR 03

I

S

I

QL

I

QH

0

I

S

I

QL

I

QH

0

I

S

SENSOR 01

NOT PRESENT

n • I

QL

n • I

QH

0

SENSOR 02 —
DIAGNOSTIC CURRENT

SENSOR 03 — DIAGNOSTIC

AND SIGNAL CURRENTS

SENSOR 01

NOT PRESENT

Dwg. WH-005

115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 [phone]

3055

MULTIPLEXED
TWO-WIRE HALL EFFECT
SENSOR IC

the overall bus current drain. When no
sensors are addressed, the net bus current
drain is the sum of quiescent currents of all
sensors on the bus (for ‘n’ sensors, the bus
quiescent current drain is n * IQ).

Bus Issues

At present, a maximum of 30 active sensors
can coexist on the same bus, each with a
different address. Address 0 is reserved for
bus current calibration in software. This
feature allows for fail-safe detection of signal
current and eliminates detection problems
caused by low signal current (IS), the opera­tion of sensors at various ambient tempera­tures, lot-to-lot variation of quiescent current,
and the addition and replacement of sensors
to the bus while in the field. Address 31 is
designed to be inactive to allow for further
address expansion of the bus (to 62 maxi­mum addresses). In order to repeat the
address cycle, the bus must be reset as
shown in Figure 1 by bringing the supply
voltage to below V

. Sensors have been

RST

designed not to ‘wrap-around’.

Magnetic Sensing

The sensor IC has been designed to respond
to an external magnetic field whose magnetic
strength is greater than BOP. It accomplishes
this by amplifying the output of an on-chip
Hall transducer and feeding it into a threshold
detector. In order that bus current is kept to
a minimum, the transducer and amplification
circuitry is kept powered down until the
sensor is addressed. Hence, the magnetic
status is evaluated only when the sensor is
addressed.

APPLICATIONS NOTES

Magnetic Actuation

The left side of Figure 2 shows the wiring of the UGN3055U when
used as a magnetic threshold detector. Pin 1 of the sensor is wired to
the positive terminal of the bus, pin 2 is connected to the bus negative
terminal, and

pin 3 has no connection.

Mechanical Actuation

The right side of Figure 2 shows the wiring of the UGN3055U when
used to detect the status of a mechanical switch. In this case, pin 3 is
connected to the positive terminal of the switch. The negative side of
the switch is connected to the negative terminal of the bus. When the
mechanical switch is closed (shorted to ground) and the correct bus
address is detected by the IC, the sensor responds with a signal
current. If the switch is open, only a diagnostic current is returned.

FIGURE 2

SENSOR CONNECTIONS

POSITIVE BUS SUPPLY

X

1 32

NC

BUS RETURN

X

1 32

SWITCH

Dwg. EH-004

External Switch Sensing

The third pin of the IC (pin 3) may be used to
detect the status of an external switch when
magnetic field sensing is not desired (and in
the absence of a magnetic field). The
allowable states for the switch are ‘open’ and
‘closed’ (shorted to sensor ground).

3055

MULTIPLEXED
TWO-WIRE HALL EFFECT
SENSOR IC

FIGURE 3

BUS INTERCONNECTION

ADDRESS

RESET

UGN3055U AND UGS3055U

(POSITIVE) BUS SUPPLY

MULTIPLEXED TWO-WIRE HALL EF­FECT SENSOR IC

01 02 28 29 30

ANALOG OUT

MICROPROCESSOR

Bus Configuration

A maximum of 30 sensors may be connected
across the same two wire bus as shown in
Figure 3. It is recommended that the sensors
use a dedicated digital ground wire to mini­mize the effects of changing ground potential
(as in the case of chassis ground in the
automotive industry).

The bus was not designed to require two-wire
twisted-pair wiring to the sensors; however,
in areas of extreme EMI (electro-magnetic
interference), it may be advisable to install a
small bypass capacitor (0.01 µF for example)
between the supply and ground terminals of
each sensor instead of using the more
expensive wiring.

Bus Driver

It is recommended that the bus be controlled
by microprocessor-based hardware for the
following reasons:

• Sensor address information may be stored
in ROM in the form of a look up table.

• Bus faults can be pinpointed by the
microprocessor by comparing the diagnos­tic response to the expected response in
the ROM look up table.

• The microprocessor, along with an A/D
converter, can also be used to self cali­brate the quiescent currents in the bus and
hence be able to easily detect a signal
response.

INTERFACE

BUS RETURN

Dwg. EH-005

• The microprocessor can also be used to filter out random line noise
by digitally filtering the bus responses.

• The microprocessor can easily keep track of the signal responses,
initiate the appropriate action; e.g., light a lamp, sound an alarm,
and also pinpoint the location of the signal.

Optimally, the microprocessor is used to control bus-driving circuitry
that will accept TTL level inputs to drive the bus and will return an
analog voltage representation of the bus current.

Interface Schematic

The bus driver is easily designed using a few operational amplifiers,
resistors, and transistors. Figure 4 shows a schematic of a recom­mended bus driver circuit that is capable of providing 6 V to 9 V
transitions, resetting the bus, and providing an analog measurement of
the current for use by the A/D input of the microprocessor.

In Figure 4, the Address pin provides a TTL-compatible input that is
used to control the Bus supply. A HIGH (5 V) input switches Q1 ON
and sets the bus voltage to 6 V through the resistor divider R4, R5,
and the Zener Z1. A LOW input switches OFF Q2 and sets the bus
voltage to 9 V. This voltage is fed into the positive input of the opera­tional amplifier OP1 and is buffered and made available at Bus Supply
(or sensor supply). Bus reset control is also available in the form of a
TTL-compatible input. When this input, which is marked Reset, is
HIGH, Q2 is switched ON and the positive input of the op amp is set to
the saturation voltage of the transistor (approximately 0 V). This resets
the bus.

A linear reading of the bus current is made possible by amplifying the
voltage generated across R6 (which is I
is a standard differential amplifier of gain R9/R7 (provided that R7 =
R8, R9 = R10). The gain of the total transimpedance amplifier is given
by:

V

= I

OUT

This voltage is available at the terminal marked Analog Out.

* R6 * R9/R7

BUS

* R6). The amplifier, OP2,

BUS

115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 [phone]

3055

MULTIPLEXED
TWO-WIRE HALL EFFECT
SENSOR IC

FIGURE 4

BUS INTERFACE SCHEMATIC

Bus Control Software

The processing of the bus current (available at Analog Out) is best
done by feeding it into the A/D input of a microprocessor. If the
flexibility provided by a microprocessor is not desired, this signal could
be fed into threshold detection circuitry; e.g., comparator, and the
output used to drive a display.

Related References

1. G. AVERY, “Two Terminal Hall. Sensor,”

ASSIGNEE: Sprague
Electric Company, North Adams, MA, United States. Patent number
4,374,333; Feb. 1983.

2. T. WROBLEWSKI and F. MEISTERFIELD, “Switch Status
Monitoring System, Single Wire Bus, Smart Sensor Arrangement
There Of,”

ASSIGNEE: Chrysler Motor Corporation, Highland Park, Ml,

United States. Patent number 4,677,308; June 1987.

+15 V

1 kΩ

9 V
Z

1

ADDRESS

RESET

10 kΩ

5 kΩ

5 kΩ

R

0.001
µF

4

OP

20 kΩ

R

5

Q

2

Q

1

1 kΩ

Q

50 Ω

3

R

50 kΩ
R

8

BUS SUPPLY

6

50 kΩ
R

7

100 kΩ

100 kΩ

R

10

OP

1 32

R

2

X

NC

9

X

1 32

SWITCH

BUS RETURN

ANALOG OUT

1

Dwg. EH-003A

3055

MULTIPLEXED
TWO-WIRE HALL EFFECT
SENSOR IC

0.181

0.176

0.560

MIN

Dimensions in Inches

(controlling dimensions)

0.183

0.178

0.086

MAX

1 2 3

0.063

0.059

0.018

0.015

45°

Dimensions in Millimeters

(for reference only)

4.65

4.52

4.60

4.47

2.18

MAX

14.22

MIN

1 2 3

1.60

1.50

45°

0.46

0.38

0.016

SEE NOTE

0.050

0.100

Dwg. MH-003C in

NOTES: 1. Tolerances on package height and width represent allowable mold offsets. Dimensions given are measured at the widest point (parting

line).

2. Exact body and lead configuration at vendor’s option within limits shown.

3. Height does not include mold gate flash.

4. Recommended minimum PWB hole diameter to clear transition area is 0.035” (0.89 mm).

5. Where no tolerance is specified, dimension is nominal.

6. Minimum lead length was 0.500” (12.70 mm). If existing product to the original specifications is not acceptable, contact sales office before
ordering.

Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the

detail specifications as may be required to permit improvements in the design of its products.

The information included herein is believed to be accurate and reliable. However, Allegro
MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other
rights of third parties which may result from its use.

SEE NOTE

1.27

2.54

0.41

Dwg. MH-003C mm

115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 [phone]