Page 1
Evaluation Board User Guide
One Technology Way • P. O . Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel : 781.329.4700 • Fax : 781.461.3113 • www.analog.com
UG-295
Advantiv EVAL-ADV7612-7511 Video Evaluation Board
FEATURES
2 HDMI inputs, 1 HDMI output
PC communication via RS-232 or USB interface
Jumperable signal paths for audio and video (jumpers can
be removed and signals connected in a different manner)
EQUIPMENT NEEDED
Computer with RS-232 (or USB) I/O to accomplish the
following:
Send scripts to the board's command line interface
Send commands to the board's repeater software and view
software output
Control the board via Advantiv video evaluation software
(AVES) application
Update the board's firmware (if desired or necessary)
SOFTWARE NEEDED
Windows OS for controlling the board via AVES application
RS-232 software for updating the board firmware (if desired
or necessary)
GENERAL DESCRIPTION
The Advantiv® EVAL-ADV7612-7511 video evaluation board
(AVEB) is a low cost solution for evaluating the performance of
the ADV7612 HDMI receiver and/or the ADV7511 HDMI
transmitter.
The evaluation board provides a Blackfin® ADSP-BF524 processor
for system control. The ADSP-BF524 offers the potential to
process audio (no audio software is included). The evaluation
board includes software (firmware) that provides a serial
command interface to control the board's functionality.
This evaluation board is available in two options.
• With HDCP support (EVAL-ADV7612-7511), available
only to licensees of HDCP
• Without HDCP support (EVAL-ADV7612-7511P)
PHOTOGRAPH OF EVALUATION BOARD
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Figure 1. Advantiv EVAL-ADV7612-7511 Video Evaluation Board with Factory Jumper Settings
Rev. 0 | Page 1 of 8
09964-001
Page 2
UG-295 Evaluation Board User Guide
TABLE OF CONTENTS
Features.............................................................................................. 1
Equipment Needed........................................................................... 1
Software Needed............................................................................... 1
General Description ......................................................................... 1
Photograph of Evaluation Board .................................................... 1
Revision History ............................................................................... 2
Evaluation Board Artwork and Components ............................... 3
REVISION HISTORY
7/11—Revision 0: Initial Version
Terminology .......................................................................................4
Evaluation Board Hardware.............................................................5
Evaluation Board Usage................................................................5
Jumpers...........................................................................................6
Evaluation Board Software...............................................................7
Upgrading the Firmware ..............................................................7
Related Links..................................................................................8
Rev. 0 | Page 2 of 8
Page 3
Evaluation Board User Guide UG-295
EVALUATION BOARD ARTWORK AND COMPONENTS
09964-002
Figure 2. Assembly Drawing (Top Side) of the EVAL-ADV7612-7511
HDMI
INPUT A
HDMI
INPUT B
ADV7612 ADV7511
DIGITAL VIDEO
DIGIT AL AUDI O
2
I
C-COMPATIBLE CONTROL BUS
ADSP-BF524
CPU
0.1 INCH
JUMPERS
0.1 INCH
JUMPERS
SDRAM
MEMORY
FLASH
MEMORY
HDMI
OUTPUT
09964-003
Figure 3. Block Diagram of the EVAL-ADV7612-7511
Table 1. Evaluation Board Hardware Components
Reference
Designator Function Description
J8, J9 HDMI inputs J8 is HDMI Port A; J9 is HDMI Port B.
J1 HDMI output This is the only video output connector.
P1 RS-232 port RS-232 interface to the computer (for user control and debug output).
P2 USB port This USB port can be used instead of RS-232 if the user's computer does not have the RS-232 interface.
SW1 Reset This switch resets the BF524 processor.
J2 Power J1 is where the 5 V, 2.5 A power supply is connected.
J7 BF524 JTAG The ICE-100B or the HPUSB-ICE is connected here to reprogram the system flash or to execute source code
JP1, JP2 Port A EDID These jumpers (see Figure 2, lower left) connect the I2C bus from the Blackfin processor to the EDID EEPROM.
JP3, JP4 Port B EDID These jumpers (see Figure 2, bottom middle) connect the I2C bus from the Blackfin processor to the EDID EEPROM.
J3, J4 Audio/control
jumpers
J5,J6 Video jumpers The digital video pixel bus signals are jumpered here for easy access and flexibility in evaluation.
debugging.
The audio bus can be jumpered among three configurations on these connectors. They also have several control
signals available for probing, as well as video syncs and clock.
Rev. 0 | Page 3 of 8
Page 4
UG-295 Evaluation Board User Guide
TERMINOLOGY
Throughout this user guide, the following terms are used.
Source
A source outputs digital audio/video over a DVI/HDMI
interface. This can be a DVD/Blu-ray player, set-top box, game
console, or any other device with a DVI/HDMI output.
Sink
A sink accepts video through a DVI/HDMI interface. This is
nearly always a display with DVI/HDMI input in the context of
this user guide.
Repeater
A repeater refers to the software that runs on the ADSP-BF524
and implements the link between a source and sink with respect
to this evaluation board.
Rev. 0 | Page 4 of 8
Page 5
Evaluation Board User Guide UG-295
EVALUATION BOARD HARDWARE
EVALUATION BOARD USAGE
The evaluation board can be connected in the ways shown in
Figure 3. By default, the video buses of the ADV7612 and
ADV7511 are directly connected, and the I
outputs of the ADV7612 are directly connected to the I
S/PDIF inputs of the ADV7511.
Note that the version of the board without HDCP support
(EVAL-ADV7612-7511P) does not work with most consumer
HDMI sources (for example, Blu-ray players) because they
automatically implement HDCP encryption. Therefore, a nonHDCP video source is needed with the non-HDCP version of
the board.
An HDCP license is required to purchase an HDCP-enabled
board. No license is required to purchase the non-HDCPenabled board.
The RS-232 command-line interface operates at 115,200 baud,
eight data bits, no parity, one stop bit, and no flow control.
Ty pi ng help via RS-232 lists the commands that can be used to
control the board as well as indicate the version of firmware and
build date.
If the board is HDCP-enabled, the Analog Devices, Inc., repeater
software starts on power-up, allowing an HDMI sink to receive
content from an HDMI/HDCP source soon after it is connected.
There are three main ways to control the board.
• Commands via RS-232
• Repeater software via RS-232
• Advantiv video evaluation software (AVES)
Commands via RS-232
This mode uses the RS-232 command-line interface. The
ADSP-BF524 powers up to a known reset state and then outputs
a prompt. At this point, commands can be entered. Typing help
prints a list of commands. Using the appropriate commands, the
user can read/write registers in the ADV7612 and ADV7511.
All registers are at their reset values.
2
S and S/PDIF
2
S and
Boards without HDCP enabled (EVAL-ADV7612-7511P)
typically use this mode.
It is possible to start the repeater software in this mode with the
startrep command via RS-232. This only works with HDCPprotected sources on an HDCP-enabled board. A non-HDCPenabled board can still operate but does not support HDCP.
Repeater Software via RS-232
This mode also offers the RS-232 command-line interface but
primarily to control the repeater software. Boards with HDCP
support (EVAL-ADV7612-7511) typically start the repeater
software on power-up. The repeater software outputs messages
via RS-232 as it establishes an encrypted HDMI link and
sources, sinks, or formats change. Registers can still be
read/written from the command line, but anything that is
written to a register can be overwritten by the repeater software.
In this mode, there are additional commands from the repeater
itself. All repeater commands are in the rep XXX format, where
XXX is the repeater command. A list of repeater commands is
displayed using the rep help command. These commands provide information about the state of the repeater, source, and sink.
AVES
AVES is a Windows®-based application that runs on a PC and
allows the user to read/write registers on the ADV7612 and
ADV7511. It also displays the individual bit fields for each
register and allows the user to modify these individual bit fields.
The software supports RS-232, USB, and I
Phase Aardvark I
2
C/SPI host adapter). Information about the
2
C (using the Total
video evaluation board can be found on the EVAL-ADV7612-7511
page on EngineerZone at http://ez.analog.com/docs/DOC-1713.
For a non-HDCP-enabled board, this software may be the
easiest way to evaluate the different modes of the ADV7612
and ADV7511.
Additional information about the software can be found on
EngineerZone at http://ez.analog.com/docs/DOC-1789, where
the latest version of the software can also be downloaded.
Rev. 0 | Page 5 of 8
Page 6
UG-295 Evaluation Board User Guide
JUMPERS
35
This evaluation board has all of the digital audio/video signals
(as well as some control signals) connected to 0.1 inch jumpers.
This provides users with easy access and maximum flexibility
when evaluating the devices.
The arrangement of the pins/signals in the schematic does not
necessarily match the physical arrangement on the board.
Figure 4 to Figure 7 match the physical arrangement on the
board and may be useful when probing these signals.
2
D_RX35
D_RX34
D_RX33
D_RX32
D_RX31
D_RX30
D_RX29
D_RX28
D_RX27
D_RX26
D_RX25
D_RX24
D_RX23
D_RX22
D_RX21
D_RX20
D_RX19
D_RX18
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
D_TX35
D_TX34
D_TX33
D_TX32
D_TX31
D_TX30
D_TX29
D_TX28
D_TX27
D_TX26
D_TX25
D_TX24
D_TX23
D_TX22
D_TX21
D_TX20
D_TX19
D_TX18
09964-004
Figure 4. J5 Configuration
Factory (Default) Setting Is for Jumpers Installed on All Odd/Even Pairs
D_RX9
D_RX8
D_RX7
D_RX6
D_RX5
D_RX4
D_RX3
D_RX2
D_RX1
D_RX0
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
D_TX17
D_TX16
D_TX15
D_TX14
D_TX13
D_TX12
D_TX11
D_TX10
D_TX9
D_TX8
D_TX7
D_TX6
D_TX5
D_TX4
D_TX3
D_TX2
D_TX1
D_TX0
Figure 5. J6 Configuration
09964-005
D_RX17
D_RX16
D_RX15
D_RX14
D_RX13
D_RX12
D_RX11
D_RX10
Factory (Default) Setting Is for Jumpers Installed on All Odd/Even Pairs
SPDIF_OUT
7511_INT
TFS0A_BF524
DSD5/DST_FL
RFS0A_BF524
DSD4/DST_ST
GND
7511_PD
LRCLK
I2S3
DSD3
I2S2
DSD2
I2S1
DSD1
GND
DSD0
SPDIF
36
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
Figure 6. J3 Configuration
Factory (Default) Setting Is for Jumpers Installed on the Following Pairs:
1 to 2, 9 to 10, 13 to 14, 17 to 18, 25 to 26
CEC_TX
36
I2S0
SCL
SDA
GND
GND
GND
DE_TX
GND
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
DTOPR1A
RSCLK0A_BF524
DSD_CLK/DST_CLK
SCLK_TX
SCLK_TX
MCLK_TX
HSYNC_TX
VSYNC_TX
VCLK_TX
Figure 7. J4 Configuration
Factory (Default) Setting Is for Jumpers Installed on the Following Pairs:
1 to 2, 5 to 6, 7 to 8, 9 to 10, 15 to 16, 19 to 20, 33 to 34
GND
33
7612_INT2
31
7612_INT1
29
7612_CSn
27
7612_RESETn
25
A_RX5
23
A_RX5
21
A_RX5
19
A_RX4
17
A_RX4
15
A_RX3
13
A_RX3
11
A_RX2
9
A_RX2
7
A_RX1
5
GND
3
A_RX2
1
A_RX2
35
CEC_RX
33
A_RX1
31
DROPR1A
29
GND
27
GND
25
GND
23
SCLK_RX
21
SCLK_RX
19
SCLK_RX
17
TSCLK0A_BF524
15
MCLK_RX
13
GND
11
GND
9
DE_RX
7
HS_CS_RX
5
VS_FIELD_RX
3
GND
1
VCLK_RX
09964-006
09964-007
Rev. 0 | Page 6 of 8
Page 7
Evaluation Board User Guide UG-295
EVALUATION BOARD SOFTWARE
UPGRADING THE FIRMWARE
The software (firmware) on the evaluation board can be
upgraded using the standard Blackfin development tools.
• VisualDSP++ 5.0 Update 8
• JTAG debugger for Blackfin processors (HPUSB-ICE or
ICE-100B) connected to the JTAG connector (J7)
Using these tools, you can connect to the ADSP-BF524
processor, run a script, and program the SPI flash memory
device (U10).
With that said, all but a very few evaluation boards are shipped with
the U-Boot boot loader firmware. If this is the case, you have the
option of upgrading the firmware using only an RS-232 cable
and software.
If you see the following output after resetting the board or
applying power, your evaluation board has U-Boot:
------------------U-Boot 2010.06 (ADI-2010R1-RC2) (Jan 12 2011 15:53:34)
CPU: ADSP bf524-0.2 (Detected Rev: 0.2) (spi
flash boot)
Board: ADI Advantiv™ Video Evaluation Board
Support: http://ez.analog.com
Clock: VCO: 300 MHz, Core: 300 MHz, System: 100
MHz
RAM: 8 MiB
SF: Detected M25P80 with page size 256, total 1
MiB
In: serial
Out: serial
Err: serial
KGDB: [on serial] ready
Hit any key to stop autoboot:
-------------------
If your evaluation board has U-Boot, you can use the following
steps to upgrade the application firmware of your board (if you
determine this is necessary). Note that these instructions
assume you are using the latest version of Tera Term for
Windows (which is free to download and use), but any RS-232
software with Ymodem upload capability should also work.
1. After you see the hit any key to stop autoboot prompt,
press a key during the countdown. You should then see a
prompt, bfin >.
2. At the prompt, type the following command:
sf probe 0:1
You should see the following:
SF: Detected M25P80 with page size 256, total
1 MiB
1024 KiB M25P80 at 0:1 is now current device
bfin>
3. At the prompt, type the following command:
loady
You should see the following output:
## Ready for binary (ymodem) download to
0x00100000 at 115200 bps...
C
4. In Te r a Ter m, unde r File, click Tr an s fe r, then YMODEM,
and select Send…
5. Select the application firmware (for example, EVAL-
ADV7612-7511_v1p3_app.bin) and click Open.
6. You should see the YMODEM send dialog box progress
quickly from 0% to 100%. If the software stalls at Packet 1
or Packet 2 for a few seconds, you may need to cancel and
retry. It is possible that you may need to repeat Step 3
through Step 5 a few times to accomplish the transfer. After
the transfer is complete, you should see the following:
CCxyzModem - CRC mode,
0(SOH)/215(STX)/0(CAN) packets, 5 retries
## Total Size = 0x000357fc = 219132
Bytes
bfin>
7. At the prompt, type the following command to erase the
application area of the SPI flash memory:
sf erase 0x60000 0xa0000
You should then see the following output:
bfin>
8. At the prompt, type the following command to program
the application area of the SPI flash memory:
sf write $(loadaddr) 0x60000 $(filesize)
You should then see the following output:
bfin>
9. At this point, if you reset your board and allow the
countdown to complete, U-Boot should launch the
application firmware that you just programmed.
Rev. 0 | Page 7 of 8
Page 8
UG-295 Evaluation Board User Guide
RELATED LINKS
Resource Description
ADV7612 Product Page, ADV7612 Dual Port Xpressview™ 225 MHz HDMI® Receiver
ADV7511 Product Page, ADV7511 225 MHz, High Performance HDMI® Transmitter with ARC
ADSP-BF524 Product Page, ADSP-BF524 Low Power Blackfin Processor with Advanced Peripherals and Low Standby Power
DOC-1751 ADV7612 Design Support Files
DOC-1740 ADV7511 Design Support Files
DOC-1713 Advantiv™ EVAL-ADV7612-7511 Video Evaluation Board
DOC-1789 Advantiv™ Video Evaluation Software
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the pers onal jurisdiction and venu e of such courts. The United Nations Conventi on on Contracts for the Internation al Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG09664-0-7/11(0)
Rev. 0 | Page 8 of 8
Loading...