Page 1
Evaluation Board User Guide
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
UG-246
Evaluation Board for the ±300°/sec, Single-Axis Digital Output Rate Gyroscope
GENERAL DESCRIPTION
e EVAL-ADXRS453Z-V is a simple breakout board that facilitates quick evaluation of the performance of the ADXRS453
±300°/sec digital output single-axis rate gyroscope in an SMTcompatible vertical mount package.
e EVAL-ADXRS453Z-V has two sets of 5-lead, 0.1-inch pin
spacing headers that allow electrical connections to be made
between the ADXRS453 and the existing system. Four mounting holes are also provided for mechanical at
EVAL-ADXRS453Z-V to the application. An external host
processor is required for communication to the ADXRS453
gyroscope.
e dimensions of the EVAL-ADXRS453Z-V are 1.3 inch ×
1.3 inch (33 mm × 33 mm) with two sets of mounting holes.
e outer set of holes is 0.125 inch (3.175 mm) in diameter and
arranged in a 0.945 inch × 0.945 inch (24 mm × 24 mm) square
around the center of the printed circuit board (PCB). e inner
set of mounting holes are 0.120 inch (3.05 mm) in diameter and
arranged in a 0.575 inch × 0.575 inch (14.6 mm × 14.6 mm)
square around the center of the PCB.
tachment of the
CIRCUIT DESCRIPTION
e board layout and schematic of the EVAL-ADXRS453Z-V
are shown in Figure 1 and Figure 2, resp
that are populated on the board is shown Table 1.
Pin names are indicated on the schematics and board layout, as
well as on the board itself, for easy identication. For additional
information, see the ADXRS453 data sheet.
ectively. A list of parts
EVAL-ADXRS453Z-V BOARD LAYOUT
1.300
1.300
09681-002
Figure 1. Dimensions shown in Inches.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 4
Page 2
UG-246 Evaluation Board User Guide
TABLE OF CONTENTS
General Description ......................................................................... 1
Circuit Description........................................................................... 1
EVAL-ADXRS453Z-V Board Layout............................................. 1
Revision History ............................................................................... 2
REVISION HISTORY
4/11—Revision 0: Initial Version
Evaluation Board Schematic............................................................3
Components List ...............................................................................4
Special Notes on Handling...............................................................4
Rev. 0 | Page 2 of 4
Page 3
Evaluation Board User Guide UG-246
EVALUATION BOARD SCHEMATIC
09681-004
Figure 2. EVAL-ADXRS453Z-V Schematic
Rev. 0 | Page 3 of 4
Page 4
UG-246 Evaluation Board User Guide
COMPONENTS LIST
See Tab le 1 for the parts list for the EVAL-ADXRS453Z-V. Note
that these parts are factory-installed.
Table 1. EVAL-ADXRS453Z-V Parts List
Reference Designator Value Package
U1 ADXRS453BEYZ LCC_V
C1 0.1 μF 0603
C2 1 μF 0603
C3 1 μF 0603
C4 1 μF 0603
L1 470 μH 1210
D1 MMSD4148T1 SOD-123
SPECIAL NOTES ON HANDLING
Note that the EVAL-ADXRS453Z-V is not reverse polarityprotected. Reversing the power supply or applying inappropriate
voltages to any pin (outside the Absolute Maximum Ratings
listed in the ADXRS453 data sheet) may damage the EVALADXRS453Z-V.
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALIT Y. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the pers onal jurisdiction and venu e of such courts. The United Nations Conventi on on Contracts for the Internation al Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG09681-0-4/11(0)
Rev. 0 | Page 4 of 4
Loading...