Page 1
5713
DUAL PERIPHERAL AND POWER DRIVER
5713
DUAL PERIPHERAL AND POWER DRIVER
— TRANSIENT PROTECTED OUTPUTS
This “mini-DlP” dual peripheral and power driver is a bipolar
monolithic integrated circuit incorporating NOR logic gates, highcurrent switching transistors, and transient suppression diodes on the
same chip. The two output transistors are capable of simultaneously
sinking 300 mA continuously at ambient temperatures of up to +70°C.
In the OFF state, this driver will withstand at least 80 V.
The UDN5713M dual driver is ideally suited for interface between
low-level or high-level logic and high-current/high-voltage loads.
Typical applications include driving peripheral loads such as incandescent lamps, light-emitting diodes, memories, and heaters with a load
current of up to 600 mA.
Data Sheet
29307B
Dwg. No. A-9789
The integral transient suppression diodes allow the use of these
drivers with inductive loads such as relays, solenoids, or stepping
motors without the need for discrete diodes. Similar devices with four
drivers per package are the 5703 and 5706.
FEATURES
■ DTL/TTL/PMOS/CMOS Compatible Inputs
■ Low Input Current
ABSOLUTE MAXIMUM RATINGS
Supply Voltage, VCC. . . . . . . . . . . . . . 7.0 V
Input Voltage, VIN. . . . . . . . . . . . . . . . . 30 V
Output Off-State Voltage,
V
. . . . . . . . . . . . . . . . . . . . . . . . 80 V
OFF
Output On-State Sink Current,
I
. . . . . . . . . . . . . . . . . . . . . . 600 mA
ON
Suppression Diode Off-State Voltage,
V
. . . . . . . . . . . . . . . . . . . . . . . . 80 V
OFF
Suppression Diode On-State Current,
I
. . . . . . . . . . . . . . . . . . . . . . 600 mA
ON
Power Dissipation at T
DISCONTINUED PRODUCT
Package. . . . . . . . . . . . . . . . . . . 1.5 W*
Each Driver . . . . . . . . . . . . . . . . . 0.8 W
Operating Free-Air Temperature Range,
T
Storage Temperature Range,
T
*Derate at the rate of 12.5 mW/°C above
TA = 25°C.
— FOR REFERENCE ONLY
. . . . . . . . . . . . . . . . . -20°C to +85°C
A
. . . . . . . . . . . . . . . . -55°C to +150°C
S
= 25°C, P
A
D
■ 300 mA Continuous Output Current
■ Stand-off Voltage of 80 V
Always order by complete part number, e.g., UDN5713M .
Page 2
5713
DUAL PERIPHERAL AND POWER DRIVER
RECOMMENDED OPERATING CONDITIONS
Min. Nom. Max. Units
Supply Voltage (V
) 4.75 5.0 5.25 V
CC
Operating Temperature Range 0 +25 +85 °C
Current into any output (ON state) — — 300 mA
ELECTRICAL CHARACTERISTICS over operating temperature range
(unless otherwise noted).
Test Conditions Limits
Driven Other
Characteristic Symbol Temp. V
“1” Input Voltage V
“0” Input Voltage V
IN(1)
IN(0)
— MIN — — — 2.0 — — V —
— MIN — — — — — 0.8 V —
CC
“0” Input Current at all
Inputs except Strobe I
“0” Input Current at Strobe I
IN(0)
IN(0)
— MAX 0.4 V 30 V — — -50 -100 µA 2
— MAX 0.4 V 30 V — — -100 -200 µA—
“1” Input Current at all
Inputs except Strobe I
“1” Input Current at Strobe I
Input Clamp Voltage V
IN(1)
IN(1)
IK
— MAX 30 V 0 V — — — 10 µA 2
— MAX 30 V 0 V — — — 20 µA—
— MIN -12 mA — — — — -1.5 V —
SWITCHING CHARACTERISTICS at VCC = 5.0 V, T
Input Input Output Min. Typ. Max. Units Notes
= 25°C
A
Limits
Characteristic Symbol Test Conditions Min. Typ. Max. Units Notes
Turn-on Delay Time t
Turn-off Delay Time t
NOTES: 1. Typical values are at VCC = 5.0 V, TA = 25°C.
2. Each input tested separately.
3. Voltage values shown in the test circuit waveforms are with respect to network ground terminal.
4. Capacitance values specified include probe and test fixture capacitance.
pd0
pd1
VS = 70 V, RL = 465 Ω (10 Watts), — 200 500 ns 3
C
= 15 pF
L
VS = 70 V, RL = 465 Ω (10 Watts), — 300 750 ns 3
C
= 15 pF
L
INPUT PULSE CHARACTERISTICS
V
= 0 V t
IN(0)
= 3.5 V t
V
IN(1)
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
W
Copyright © 1976, 1997, Allegro MicroSystems, Inc.
= 7 ns tp = 1 µs
f
= 14 ns PRR = 500 kHz
r
Page 3
5713
DUAL PERIPHERAL AND POWER DRIVER
ELECTRICAL CHARACTERISTICS over operating temperature range
(unless otherwise noted).
Test Conditions Limits
Driven Other
Characteristic Symbol Temp. V
CC
Input Input Output Min. Typ. Max. Units Notes
“1” Output Reverse Current l
“0” Output Voltage V
Diode Leakage Current I
Diode Forward Voltage Drop V
“1” Level Supply Current l
“0” Level Supply Current l
NOTES: 1. Typical values are at V
2. Per package.
3. Diode leakage current measured at VR = 80 V.
4. Diode forward voltage drop measured at IF = 300 mA.
5. Capacitance values specified include probe and test fixture capacitance.
OFF
ON
LK
D
CC(1)
CC(0)
= 5.0 V, TA = 25°C.
CC
— MIN 2.0 V 0 V 80 V — — 100 µA—
— OPEN 2.0 V 0 V 80 V — — 100 µA—
— MIN 0.8 V 0.8 V 150 mA — 0.35 0.5 V —
— MIN 0.8 V 0.8 V 300 mA — 0.5 0.7 V —
NOM NOM 0 V 0 V OPEN — — 200 µA3
NOM NOM V
CC
V
CC
— — 1.5 1.75 V 4
NOM MAX 5.0 V 5.0 V — — 8.0 13 mA 1, 2
NOM MAX 0 V 0 V — — 36 50 mA 1, 2
Dwg. No. A-9123A
Dwg. No. A-7628C
Page 4
5713
DUAL PERIPHERAL AND POWER DRIVER
0.280
0.240
0.210
MAX
0.015
MIN
1
0.070
0.045
8
Dimensions in Inches
58
4
0.005
0.400
MIN
0.355
0.150
0.115
0.022
0.014
0.100
BSC
Dimensions in Millimeters
(Based on 1” = 25.4 mm)
5
0.014
0.008
0.355
0.204
0.430
MAX
0.300
BSC
Dwg. MA-001-8A in
7.11
6.10
1
1.77
1.15
10.16
9.02
5.33
MAX
0.39
MIN
0.558
0.356
NOTES: 1. Lead thickness is measured at seating plane or below.
2. Lead spacing tolerance is non-cumulative.
3. Exact body and lead configuration at vendor’s option
within limits shown.
2.54
BSC
10.92
MAX
7.62
BSC
4
0.13
MIN
3.81
2.93
Dwg. MA-001-8A mm
Allegro MicroSystems, Inc. reserves the right to make, from time to time,
such departures from the detail specifications as may be required to permit
improvements in the design of its products.
The information included herein is believed to be accurate and reliable.
However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor
for any infringements of patents or other rights of third parties which may result
from its use.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
Loading...