Datasheet UCC1839, UCC2839, UCC3839 Datasheet (UNITRODE)

Download

Page 1

查询UCC1839供应商

Secondary Side Average Current Mode Controller

UCC1839 UCC2839 UCC3839

FEATURES

• Practical Secondary Side Control of Isolated Power Supplies

• Provides a Self Regulating Bias Supply From a High Input Voltage Using an External N-Channel Depletion Mode FET

• Onboard Precision, Fixed Gain, Differential Current Sense Amplifier

• Wide Bandwidth Current Error Amplifier

• 5V Reference

• High Current, Programmable Gm

Amplifier Optimized to Drive Opto-couplers

DESCRIPTION

The UCC3839 provides the control functions for secondary side average current mode control in isolated power supplies. Start up, pulse width modulation and MOSFET drive must be accomplished independently on the primary side. Communication from secondary to primary side is anticipated through an opto-isolator.

Accordingly, the UCC3839 contains a fixed gain current sense amplifier, voltage and current error amplifiers, and a Gm type buffer/driver amplifier for the opto-isolator. Additional housekeeping functions include a precision 5V reference and a bias supply regulator.

Power for the UCC3839 can be generated by peak rectifying the voltage of the secondary winding of the isolation transformer. From this unregulated voltage, the UCC3839’s bias supply regulator will generate its own 7.5V bias supply using an external, N-channel, depletion mode FET.

The UCC3839 can be configured for traditional average current mode control where the output of the voltage error amplifier commands the current error amplifier. It can also be configured for output voltage regulation with average current mode short circuit current limiting, employing two parallel control loops regulating the output voltage and output current independently.

BLOCK DIAGRAM

04/99

UDG-97011

Page 2

ABSOLUTE MAXIMUM RATINGS

Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V

Supply Current

(LED not connected) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2mA

(LED connected) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14mA

Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3V to 15V

Power Dissipation at TA = 60°C

(LED not connected). . . . . . . . . . . . . . . . . . . . . . . . . . 20mW

(LED connected). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55mW

Storage Temperature . . . . . . . . . . . . . . . . . . . –65°C to +150°C

Junction Temperature. . . . . . . . . . . . . . . . . . . –55°C to +150°C

Lead Temperature (Soldering, 10sec.) . . . . . . . . . . . . . +300°C

Currents are positive into, negative out of the specified terminal. Consult Packaging Section of Databook for thermal limitations and considerations of package.

UCC1839 UCC2839 UCC3839

CONNECTION DIAGRAMS

DIL-14, SOIC-14 (Top View) J or N Package, D Package

ELECTRICAL CHARACTERISTICS:

UCC2839 and –55°C to 125°C for the UCC1839. V

PARAMETER TEST CONDITIONS MIN TYP MAX UNITS

Current Error Amplifier

VIO 10 mV

AVOL 60 dB

CMRR V

PSRR VLINE = 10V to 20V 60 dB

CAO High CA– = 1V, CA+ = 1.1V, ICAO = –100µA 4.8 7 V

ICAO CA– = 1V, CA+ = 1.1V, CAO = 0.5V –500 –250 µA

CAO Low CA– = 1V, CA+ = 0.9V, ICAO = 500µA 0.2 0.4 V

GBW F = 100kHz, TA = 25°C 3 5 MHz

Voltage Error Amplifier

VA– 1.475 1.5 1.525 V

AVOL 60 dB

PSRR V

VAO High IVAO = –100µA to 100µA 4.8 5 5.2 V

IVAO VA– = 1.45V, VAO = 0.5V –500 –250 µA

VAO Low VA– = 1.55V, VAO = 0.5V, IVAO = 500µA 0.2 0.4 V

GBW (Note 1) 3 5 MHz

Current Sense Amplifier

CSO Zero CS+ = CS– = –0.3V to 5.5V, I

AV CS+ = 0, CS– = 0mV to –200mV 7.8 8 8.2 V/V

Current Sense Amplifier (cont.)

Slew Rate CS+ = 0, CS– = 0mV to –0.5V 2 4 V/µs

CSO CS+ = –200mV, CS– = –700mV 4.8 5 5.2 V

LED Driver

LED LED = 5.5V, CA– = 1V, CA+ = 1.1V, RG = 400 0 10 µA

Gm LED = 5.5V, CAO = 1V to 3V, RG = 400 2.25 2.5 2.75 mS

Slew Rate CAO = 2V to 2.5V, LED = 400Ω to 5.5V, RG = 400 2 4 V/µs

CM = 0.5V to 5.5V 60 dB

LINE = 10V to 20V 60 dB

LED = 5.5V, CA– = 1V, CA+ = 0.9V, RG = 400 9 10 11 mA

Unless otherwise specified, 0°C to 70°C for the UCC3839, –40°C to 85° for the

= 10V, RG = 400Ω. TA=TJ.

LINE

CSO = –100µA to 100µA 0.95 1 1.05 V

Page 3

UCC1839 UCC2839 UCC3839

ELECTRICAL CHARACTERISTICS:

UCC2839 and –55°C to 125°C for the UCC1839. V

PARAMETER TEST CONDITIONS MIN TYP MAX UNITS

Precision Reference

REF T

VA+/REF 0.298 0.3 0.302 V/V

VDD Regulator

VDD IDD = 0mA to –15mA, V

IVDD VLINE = 10V to 40V, CA– = 0V, CA+ = 1V, VA– = 2.9V, CS+

Note 1: Guaranteed by design. Not 100% tested in production.

J = 25°C 4.95 5 5.05 V

IREF = 0mA to 1mA, VLINE = 10V to 20V 4.9 5.1 V

= CS– = 0, IREF = 0

Unless otherwise specified, 0°C to 70°C for the UCC3839, –40°C to 85° for the

= 10V, RG = 400Ω. TA=TJ.

LINE

LINE = 10V to 40V 7 7.5 8 V

1.3 2 mA

PIN DESCRIPTIONS

CA–: Current Error Amplifier Negative Input. CAO: Current Error Amplifier Output. Output source cur-

rent is limited, and output sink current is guaranteed to be greater than the VAO output source current. Current loop compensation components are generally connected to CAO and CA–.

CA+: Current Error Amplifier Positive Input. CS–: Current Sense Amplifier Negative Input. CSO: Current Sense Amplifier Output. Internally set gain

OUT/VIN = 8 VIN = 0V results in CSO = 1V.

CS+: Current Sense Amplifier Positive Input. GM: Gm (transconductance) Programming Pin. Resistor

GM = 400Ω to GND.

GND: Chip Ground. LED: Output of LED Driver. Connect LED from VDD pin

to LED.

REF: 5V Precision Reference Buffer Output. Minimum Decoupling Capacitance = 0.01µF

VA–: Voltage Error Amplifier Negative Input. Voltage Error Amplifier is internally referenced to 1.5V

VAO: Voltage Error Amplifier Output. In a two loop average current mode control configuration, VAO is connected to CA+ and is the current command signal. VAO is internally clamped not to exceed 5V for short circuit control. In a single loop voltage mode control configuration with a parallel average short circuit current control loop, VAO is connected directly to CAO. Output source current is limited, and output sink current is guaranteed to be greater than the CAO output source current.

VDD: 7.5V Regulator output. Supply for most of the chip. Minimum Decoupling Capacitance = 0.01µF

VGATE: External FET Gate Control Voltage.

APPLICATION INFORMATION

Fig. 1 shows a typical secondary side average current mode controller configuration using the UCC3839. In this configuration, output voltage is sensed and regulated by the voltage error amplifier. Its output, VAO provides the reference for the current error amplifier at the CA+ pin. VAO can be connected to CA+ directly or through a resistive divider depending on the particular application requirements.

Average current mode control needs accurate output current information which is provided by a low value current sense resistor. The voltage proportional to the converter’s output current is sensed and amplified by the

precision current sense amplifier of the chip. The onboard current sense amplifier has a gain of 8 and is intended for differential sensing of the shunt voltage with a common mode voltage range from 0V up to 5V. The output of the current sense amplifier, CSO is 1V for zero input which guarantees that the circuit can control currents down to 0A.

The CSO signal is fed to the CA– input of the current error amplifier through a resistor. The current error amplifier takes the VAO and CSO signals and generates the error signal for the pulse width modulator.

Page 4

APPLICATION INFORMATION (cont.)

Since the PWM function is located on the primary side of the power converter the CAO signal must be sent across the safety isolation boundary. The UCC3839 anticipates an opto-coupler to provide isolation between primary and secondary. Therefore, CAO drives a transconductance amplifier that controls LED current in an opto-isolator. During start up and when CAO exceeds 4V, the current in the LED drops to zero. Maximum LED current is obtained during normal operation as CAO reaches its lowest potential. Its value is determined by the programming resistor value from the GM pin to circuit GND.

An alternative secondary side controller configuration is introduced in Fig. 2. In this circuit, the voltage and current control loops of the UCC3839 are connected parallel. It can be achieved by connecting the VAO and CAO pins together. The error amplifier with the lower output

UCC1839 UCC2839

voltage controls the current in the opto-coupler providing the feedback signal for the PWM section on the primary side. Voltage regulation is still maintained by the voltage error amplifier until a user programmable output current is reached. At this time CAO will take control over the Gm amplifier and the output current of the converter will be regulated while the output voltage falls below its nominal value. This current level is set at the CA+ input by a resistive divider from the 5V reference of the chip.

Since the chip is powered from a peak rectifier which maintains the bias supply for the UCC3839 even under short circuit conditions, both of these techniques can be used to eliminate the short circuit runaway problem in isolated power supplies using peak current mode control on the primary side.

Figure 1. Secondary side average current mode controller.

UDG-97012

Page 5

APPLICATION INFORMATION (cont.)

UCC1839 UCC2839 UCC3839

Figure 2. Voltage mode with average current short circuit limit.

UDG-97014

Figure 3. Typical primary side circuit for use with secondary side average current mode controller.

UNITRODE CORPORATION 7 CONTINENTALBLVD. • MERRIMACK, NH 03054 TEL. (603) 424-2410 FAX (603) 424-3460

UDG-97014

Page 6

IMPORTANT NOTICE

T exas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability.

TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty . Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements.

CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICA TIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERST OOD TO BE FULLY AT THE CUSTOMER’S RISK.

In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards.

TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.