Datasheet UB [smd] ACSWT Series Datasheet

application of rated voltage, leakage current is not more

30% of initial value

for 1000 hours, they

V-CHIP ALUMINUM ELECTROLYTIC CAPACITOR—Wide Temperature

ACSWT

FEATURES

●Temperature up to +105℃ With load life of 1000~2000 hours

●High stability and

●Available for high density

surface mounting

●Reflow soldering is available

reliability

S P E C I F I C AT I O N S

Operating Temperature Range

Rated Voltage Range Nominal

Capacitance Range Capacitance Tolerance

Leakage current

Tan δ

Stability at Low Temperature

Load life

Shelf Life

Resistance to Soldering Heat

Applicable Standards

After 2 minutes’ than 0.01CV or 3uA, whichever is greater.

Measurement frequency: 120Hz, Temperature: 20℃

Rated Voltage(V) 4 6.3 10 16 25 35 50

Tan δ(max)

Measurement frequency: 120Hz

Impedance ratio

ZT/Z20(max)

After 2000 hours’ application of rated voltage at 85℃. Capacitors meet the characteristics requirements listed at right.

After leaving capacitors under no load at 85℃ meet the specified value for load life characteristics listed above

The capacitors shall be keep on the hot plate maintain at 250℃ for 30 seconds, after removing from the hot plate and restored at room temperature, they meet the following requirement.

JIS C-5141 and JIS C-5102

-40~+105℃ 4~50VDC

0.1µF ~1000µF

±20%(M) at 120Hz, 20℃

0.35 0.26 0.20 0.16 0.14 0.12 0.12

Rated voltage(V) 4 6.3 10 16 25 35 50

Z-25℃/Z+20℃ Z-40℃/Z+20℃

Capacitance

Change

Tan δ

Leakage Current Initial specified value or less

Capacitance Change

Leakage Current

7 4 3 2 2 2 2

15 8 6 4 4 3 3

Within ±20% of initial value (Within ± for 4V)

200% or less of initial

specified value

Within±10% of initial value

Tan δ

Initial specified of value or less Initial specified of value or less

V-CHIP ALUMINUM ELECTROLYTIC CAPACITOR—Wide Temperature

ACSWT

◆Dimensions&Marking

Φ4X5.4 Φ5X5.4 Φ6.3X5.4 Φ6.3X7.7 Φ8X10.5 Φ10X10.5

A 1.8 2.1 2.4 2.4 2.9 3.2

B 4.3 5.3 6.6 6.6 8.3 10.3

C 4.3 5.3 6.6 6.6 8.3 10.3

E 1.0 1.3 2.2 2.2 3.1 4.5 L 5.4 5.4 5.4 7.7 10.5 10.5

H 0.5~0.8 0.8~1.1

◆Standard size & Maximum permissible ripple current

V

uF 0G 0J 1A 1C 1E 1V 1H

0.1 4x5.4 0.7

0.22 4x5.4 1.6

0.33 4x5.4 2.5

0.47 4x5.4 3.5

1.0 4x5.4 4

2.2 4x5.4 11

3.3 4x5.4 13 4x5.4 13

4.7 4x5.4 13 4x5.4 14 5x5.4 16 10 4x5.4 18 5x5.4 20 5x5.4 21 6.3x5.4 24 22 4x5.4 22 5x5.4 25 5x5.4 37 6.3x5.4 36 6.3x5.4 38 6.3x7.7 51 33 4x5.4 18 5x5.4 27 5x5.4 30 6.3x5.4 40 6.3x5.4 44 6.3x5.4 42 6.3x7.7 60 47 4x5.4 23 5x5.4 33 6.3x5.4 41 6.3x5.4 48 6.3x5.4 48 6.3x7.7 49 6.3x7.7 63

100 5x5.4 42 6.3x5.4 50 6.3x5.4 53 6.3x5.4 60 6.3x7.7 91 8x10.5 155 8x10.5 155 150 6.3x5.4 61 6.3x5.4 55 6.3x5.4 62 6.3x7.7 95 8x10.5 140 8x10.5 155 10x10.5 300 220 6.3x5.4 68 6.3x7.7 105 6.3x7.7 105 6.3x7.7 105 8x10.5 175 10x10.5 300 330 6.3x7.7 73 6.3x7.7 105 8x10.5 175 8x10.5 195 10x10.5 220 470 6.3x7.7 105 8x10.5 170 8x10.5 210 8x10.5 310 680 8x10.5 210 8x10.5 210 10x10.5 230 10x10.5 350

1000 8x10.5 260 10x10.5 230

Case size Allowable ripple

4 6.3 10 16 25 35 50

V-CHIP ALUMINUM ELECTROLYTIC CAPACITOR—Wide Temperature

ACSWT

◆HOW TO ORDER (Note: Below two order methods only is a reference, you can use any order method you consider convenience. Below example only tell you product key order parameters)

A, Use UB P/N as below:

ACSWT 1H 0R1 M 004054 S S

Capacitor Type

Please refer document “How to order UB Aluminum electrolytic capacitor” for details B, Fill in your requirement in the blank:

Capacito r Type

Please see below an example:

Capacito r Type

ACSWT 50VDC 0.1uF

Rated Voltage

Rated Voltage (VDC orVAC)

Rated Capaci tance

Rated Capacitance

Capacitance Tolerance

±20%

Capacitance Tolerance

D/L/

d(φ)

(unite: mm)

D/L/

d(φ)

(unite: mm)

Terminal Type(Vertical ,Radial, Snap in, Lug, Screw, SMD)

Size Code Terminal

Type

Lead forming(1,Forming cut; 2,Straight cut; 3, Kink forming; 4,Kink cut; 5,Axial; 6,SMD)

Lead Forming

Packaging Mode (bulk or Reel-pack or Ammo-pac k)

4/5.4 SMD SMD Reel