Page 1
Micropower with high merit factor CMOS operational amplifiers
Features
TSV6290, TSV6290A, TSV6291, TSV6291A
■ Low supply voltage: 1.5 V – 5.5 V
■ Rail-to-rail input and output
■ Low input offset voltage: 800 µV max
(A version)
■ Low power consumption: 29 µA typical
■ Gain bandwidth product: 1.3 MHz typical
■ Stable when used in gain configuration
■ Micropackages: SC70-5/6, SOT23-5/6
■ Low input bias current: 1 pA typical
■ Extended temperature range: -40 to +125°C
■ 4 kV human body model
Applications
■ Battery-powered applications
■ Portable devices
■ Signal conditioning
■ Active filtering
■ Medical instrumentation
Description
The TSV6290 and the TSV6291 are single
operational amplifiers with a high bandwidth while
consuming only 29 µA. They must be used in a
gain configuration (G<-3, G>+4).
V
In+
In+
1
1
+
+
_
V
V
CC-
CC-
In-
In-
_
2
2
3
3
V
5
5
CC+
CC+
4
4
Out
Out
TSV6291ICT/ILT
SC70-5/SOT23-5
In+
1
+
V
CC-
In-
_
2
3
6
5
4
V
CC+
SHDN
Out
TSV6290ICT/ILT
SC70-6/SOT23-6
The TSV6290 comes with a shutdown function.
The TSV6290 and TSV6291 present a high
tolerance to ESD, sustaining 4 kV for the human
body model.
Additionally, the TSV6290 and TSV6291 are
offered in SC70-5/6 and SOT23-5/6
micropackages, with extended temperature
ranges from -40° C to +125° C.
All these features make the TSV629x ideal for
sensor interfaces, battery-supplied and portable
applications, as well as active filtering.
With a very low input bias current and low offset
voltage (800 µV maximum for the A version), the
TSV629x family of devices is ideal for applications
requiring precision. The devices can operate at a
power supply ranging from 1.5 to 5.5 V, and
therefore suit battery-powered devices, extending
battery life.
March 2010 Doc ID 17117 Rev 1 1/23
www.st.com
23
Page 2
Contents TSV6290, TSV6290A, TSV6291, TSV6291A
Contents
1 Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 3
2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.1 Operating voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2 Rail-to-rail input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.3 Rail-to-rail output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.4 Shutdown function (TSV6290) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.5 Optimization of DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.6 Driving resistive and capacitive loads . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.7 PCB layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.8 Macromodel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.1 SOT23-5 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.2 SOT23-6 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.3 SC70-5 (or SOT323-5) package mechanical data . . . . . . . . . . . . . . . . . . 18
4.4 SC70-6 (or SOT323-6) package mechanical data . . . . . . . . . . . . . . . . . . 19
5 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2/23 Doc ID 17117 Rev 1
Page 3
TSV6290, TSV6290A, TSV6291, TSV6291A Absolute maximum ratings and operating conditions
1 Absolute maximum ratings and operating conditions
Table 1. Absolute maximum ratings (AMR)
Symbol Parameter Value Unit
(3)
(4)
(1)
(3)
(8)
(2)
(7)
(9)
(5)(6)
V
V
CC-
CC-
6V
±V
CC
-0.2 to V
+0.2 V
CC+
V
10 mA
-0.2 to V
+0.2 V
CC+
205
250
°C/W
240
232
4kV
300 V
1.5 kV
V
CC
V
V
I
in
Supply voltage
Differential input voltage
id
Input voltage
in
Input current
SHDN Shutdown voltage
T
stg
Storage temperature -65 to +150 °C
Thermal resistance junction to ambient
SC70-5
R
thja
SOT23-5
SOT23-6
SC70-6
T
Maximum junction temperature 150 °C
j
HBM: human body model
ESD
MM: machine model
CDM: charged device model
Latch-up immunity 200 mA
1. All voltage values, except differential voltage, are with respect to network ground terminal.
2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
3. Vcc-Vin must not exceed 6 V, Vin must not exceed 6 V.
4. Input current must be limited by a resistor in series with the inputs.
5. Short-circuits can cause excessive heating and destructive dissipation.
are typical values.
6. R
th
7. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for
all couples of pin combinations with other pins floating.
8. Machine mode: a 200 pF capacitor is charged to the specified voltage, then discharged directly between
two pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin
combinations with other pins floating.
9. Charged device model: all pins plus package are charged together to the specified voltage and then
discharged directly to the ground.
Table 2. Operating conditions
Symbol Parameter Value Unit
V
V
T
CC
icm
oper
Supply voltage 1.5 to 5.5 V
Common mode input voltage range V
CC-
-0.1 to V
+0.1 V
CC+
Operating free air temperature range -40 to +125 °C
Doc ID 17117 Rev 1 3/23
Page 4
Electrical characteristics TSV6290, TSV6290A, TSV6291, TSV6291A
2 Electrical characteristics
Table 3. Electrical characteristics at V
Symbol Parameter Conditions Min. Typ. Max. Unit
DC performance
and R
= +1.8 V with V
connected to VCC/2 (unless otherwise specified)
L
CC+
= 0 V, V
CC-
= VCC/2, T
icm
= 25° C,
amb
V
DV
CMR
A
V
V
Offset voltage
io
Input offset voltage drift 2 μV/°C
io
Input offset current
I
io
(V
out=VCC
Input bias current
I
ib
(V
out=VCC
Common mode rejection ratio
20 log (ΔV
Large signal voltage gain
vd
High level output voltage
OH
Low level output voltage
OL
Isink
I
out
Isource
I
Supply current (per operator)
CC
AC performance
/2)
/2)
/ΔVio)
ic
(1)
(1)
TSV6290-TSV6291
TSV6290A-TSV6291A
< Top < T
T
min
max
TSV6290-TSV6291
TSV6290A-TSV6291A
< Top < T
T
min
max
< Top < T
T
min
0 V to 1.8 V, V
< Top < T
T
min
R
= 10 kΩ, V
L
< Top < T
T
min
R
=10kΩ 35 5
L
< Top < T
T
min
max
= 0.9 V 53 74
out
max
= 0.5 V to 1.3 V 78 95
out
max
max
51
73
50
110
1100
110
1100
4
0.8
mV
6
2
pA
pA
dB
dB
mV
RL=10kΩ 435
mV
< Top < T
T
min
V
= 1.8 V 6 12
out
< Top < T
T
min
V
= 0 V 6 10
out
< Top < T
T
min
No load, V
< Top < T
T
min
max
max
max
out=VCC
max
4
4
/2 25 31
50
mA
mA
µA
33
GBP Gain bandwidth product RL=10kΩ, CL= 100 pF 1.1 MHz
Gain Minimum gain for stability
SR Slew rate
1. Guaranteed by design.
Phase margin = 60°, Rf = 10 kΩ,
=10kΩ, CL=20pF
R
L
RL=10kΩ, CL= 100 pF,
Vout = 0.5 V to 1.3 V
+4
-3
0.33 V/μs
4/23 Doc ID 17117 Rev 1
V/V
Page 5
TSV6290, TSV6290A, TSV6291, TSV6291A Electrical characteristics
Table 4. Shutdown characteristics VCC= 1.8 V (TSV6290)
Symbol Parameter Conditions Min. Typ. Max. Unit
DC performance
I
CC
t
on
t
off
V
V
I
IH
I
IL
I
OLeak
SHDN = V
Supply current in shutdown
mode (all operators)
Amplifier turn-on time
Amplifier turn-off time
SHDN logic high 1.3 V
IH
SHDN logic low 0.5 V
IL
T
T
R
V
R
V
min
min
L
CC-
L
CC+
SHDN current high SHDN =V
SHDN current low SHDN =V
Output leakage in shutdown
mode
SHDN
T
min
CC-
< Top < 85° C 200 nA
< Top < 125° C 1.5 µA
=5kΩ, V
out=VCC-
to
+0.2V
=5kΩ, V
out=VCC+
- 0.5 to
-0.7V
CC+
CC-
=V
CC-
< Top < T
max
2.5 50 nA
300 ns
30 ns
10 pA
10 pA
50 pA
1nA
Doc ID 17117 Rev 1 5/23
Page 6
Electrical characteristics TSV6290, TSV6290A, TSV6291, TSV6291A
Table 5. V
CC+
= +3.3 V, V
= 0 V, V
CC-
= VCC/2, T
icm
= 25° C, RL connected to VCC/2
amb
(unless otherwise specified)
Symbol Parameter Min. Typ. Max. Unit
DC performance
V
DV
CMR
A
V
V
Offset voltage
io
Input offset voltage drift 2 μV/°C
io
I
Input offset current
io
I
Input bias current
ib
Common mode rejection ratio
20 log (ΔV
Large signal voltage gain
vd
High level output voltage
OH
Low level output voltage
OL
Isink
I
out
Isource
I
Supply current (per operator)
CC
AC performance
/ΔVio)
ic
(1)
(1)
TSV6290-TSV6291
TSV6290A-TSV6291A
< Top < T
T
min
max
TSV6290-TSV6291
TSV6290A-TSV6291A
110pA
T
min
< Top < T
max
1 100 pA
110pA
T
< Top < T
min
0V to 3.3V, V
T
< Top < T
min
R
=10 kΩ, V
T
L
min
out
< Top < T
max
= 1.65 V 57 79 dB
out
max
53 dB
= 0.5 V to 2.8 V 81 98 dB
max
76 dB
1 100 pA
RL=10kΩ 35 5
< Top < T
T
min
R
=10kΩ 435
L
< Top < T
T
min
V
= 5 V 23 45
out
< Top < T
T
min
V
= 0 V 23 38
out
< Top < T
T
min
No load, V
T
< Top < T
min
max
max
max
max
=2.5V 26 33 µA
out
max
50
20
20
4
0.8
6
2
50
35 µA
mV
mV
mV
mA
mA
GBP Gain bandwidth product RL=10kΩ, CL= 100 pF 1.2 MHz
Gain Minimum gain for stability
SR Slew rate
1. Guaranteed by design.
Phase margin = 60°, Rf = 10 kΩ,
RL=10kΩ, CL=20pF
RL=10kΩ, CL= 100 pF,
= 0.5 V to 2.8 V
V
out
+4
-3
0.4 V/μs
6/23 Doc ID 17117 Rev 1
V/V
Page 7
TSV6290, TSV6290A, TSV6291, TSV6291A Electrical characteristics
Table 6. V
CC+
= +5 V, V
= 0 V, V
CC-
= VCC/2, T
icm
= 25° C, RL connected to VCC/2
amb
(unless otherwise specified)
Symbol Parameter Min. Typ. Max. Unit
DC performance
V
DV
CMR
SVR
A
V
V
I
I
Offset voltage
io
Input offset voltage drift 2 μV/°C
io
I
Input offset current
io
I
Input bias current
ib
Common mode rejection ratio
20 log (ΔV
Supply voltage rejection ratio 20
log (ΔVCC/ΔVio)
Large signal voltage gain
vd
High level output voltage
OH
Low level output voltage
OL
I
sink
out
I
source
Supply current (per operator)
CC
AC performance
/ΔVio)
ic
(1)
(1)
TSV6290-TSV6291
TSV6290A-TSV6291A
< Top < T
T
min
max
TSV6290-TSV6291
TSV6290A-TSV6291A
110pA
T
min
< Top < T
max
1 100 pA
110pA
T
< Top < T
min
0V to 5V, V
T
< Top < T
min
= 1.8 to 5 V 75 102 dB
V
CC
< Top < T
T
min
RL=10 kΩ, V
< Top < T
T
min
R
=10kΩ 35 7
L
< Top < T
T
min
R
=10kΩ 635
L
< Top < T
T
min
V
=5V 40 69
out
< Top < T
T
min
V
= 0 V 40 74
out
< Top < T
T
min
No load, V
< Top < T
T
min
max
= 2.5 V 60 80 dB
out
max
max
= 0.5 V to 4.5 V 85 98 dB
out
max
max
max
max
max
=2.5V 30 36 µA
out
max
55
73
80
50
35
35
1 100 pA
4
0.8
6
2
50
38 µA
mV
mV
mV
mA
mA
GBP Gain bandwidth product R
Gain Minimum gain for stability
SR Slew rate
=10kΩ, CL= 100 pF 1.3 MHz
L
Phase margin = 60°, Rf = 10 kΩ,
RL=10kΩ, CL=20pF
RL=10kΩ, CL= 100 pF,
= 0.5 V to 4.5 V
V
out
+4
-3
V/V
0.5 V/μs
Doc ID 17117 Rev 1 7/23
Page 8
Electrical characteristics TSV6290, TSV6290A, TSV6291, TSV6291A
Table 6. V
= +5 V, V
CC+
= 0 V, V
CC-
= VCC/2, T
icm
= 25° C, RL connected to VCC/2
amb
(unless otherwise specified) (continued)
Symbol Parameter Min. Typ. Max. Unit
e
Equivalent input noise voltage f = 1 kHz 70
n
Av = -10, f
THD Total harmonic distortion
1. Guaranteed by design.
Table 7. Shutdown characteristics VCC= 5 V (TSV6290)
100 kΩ,
V
icm
Symbol Parameter Conditions Min. Typ. Max. Unit
DC performance
SHDN
I
CC
t
on
t
off
V
V
I
IH
I
IL
I
OLeak
Supply current in shutdown
mode (all operators)
Amplifier turn-on time
Amplifier turn-off time
SHDN logic high 4.5 V
IH
SHDN logic low 0.5 V
IL
< Top < 85° C 200 nA
T
min
< Top < 125° C 1.5 µA
T
min
R
=5kΩ, V
L
V
CC-
=5kΩ, V
R
L
V
CC+
SHDN current high SHDN =V
SHDN current low SHDN =V
Output leakage in shutdown
mode
SHDN
T
< Top < T
min
= 1 kHz, RL=
in
= Vcc/2, Vin = 40 mVpp
= V
IL
out=VCC-
to
+0.2V
out=VCC+
- 0.5 V to
-0.7V
CC+
CC-
=V
CC-
max
0.15 %
550 nA
300 ns
30 ns
10 pA
10 pA
50 pA
1nA
nV
-----------Hz
8/23 Doc ID 17117 Rev 1
Page 9
TSV6290, TSV6290A, TSV6291, TSV6291A Electrical characteristics
10000 100000 1000000
0
5
10
15
20
VCC=5V
VCC=1.5V
Closed loop gain = -10
T=25 C,C
Load
=100pF, V
icm=VCC
/2,
R
Load
=2.2kΩ for Iout giving
minimum stability on a typical part
Gain (dB)
Frequency (Hz)
Figure 1. Supply current vs. supply voltage
at V
icm
= VCC/2
Figure 3. Output current vs. output voltage at
V
= 5 V
CC
Figure 2. Output current vs. output voltage at
VCC= 1.5 V
Figure 4. Peaking at closed loop gain = -10 at
VCC= 1.5 V and VCC= 5 V
Figure 5. Peaking at closed loop gain = -3,
V
= 1.5 V
CC
12
10
8
6
R
Gain (dB)
R
minimum stability
4
Load
Load
on a typical part
2
0
10000 100000 1000000
R
=10k
Load
R
=100k
Load
=100kΩ to VCC/2
=10kΩ for I
giving
out
Frequency (Hz)
Ω
Figure 6. Peaking at closed loop gain = -3,
V
= 5 V
CC
12
10
Ω
8
R
=100kΩ to VCC/2
Load
R
=10kΩ for I
Load
6
Gain (dB)
minimum stability
on a typical part
4
giving
out
2
0
10000 100000 1000000
Frequency (Hz)
Doc ID 17117 Rev 1 9/23
R
=10k
Ω
Load
R
=100k
Ω
Load
Page 10
Electrical characteristics TSV6290, TSV6290A, TSV6291, TSV6291A
T=25°C
R
Load
=10kΩ, C
Load
=100pF, ACL=−10
Vin: from V
CC+
−0.5V to 0.5V
SR calculated from 10% to 90%
V
icm=VCC
/2
T=125°C
T=−40°C
Slew rate (V/ s)
Supply voltage (V)
Vcc=5V
T=25 C
V
icm
=4.5V
V
icm
=2.5V
Input equivalent noise density (nV/VHz)
Frequency (Hz)
Figure 7. Positive slew rate vs. supply
voltage in closed loop
T=125°C
T=25°C
T=−40°C
Slew rate (V/ s)
R
=10kΩ, C
Load
Vin: from 0.5V to V
SR calculated from 10% to 90%
V
icm=VCC
/2
=100pF, ACL=−10
Load
−0 . 5 V
CC+
Supply voltage (V)
Figure 9. Slew rate vs. supply voltage in open
loop
Figure 8. Negative slew rate vs. supply
voltage in closed loop
Figure 10. Slew rate timing in open loop
Open loop configuration, T = 25 C
R
=10kΩ, C
Load
Vin=1VPP, V
Slew rate (V/ s)
SR calculated from 0.5V to VCC-0.5V
Supply voltage (V)
Load
icm=VCC
=100pF,
/2
Amplitude (V)
Open loop,R
C
=100pF, V
Load
T=25°C, VCC=5V, Vin = 1V
Load
=10k
icm=VCC
Time (µs)
Figure 11. Slew rate timing in closed loop Figure 12. Noise at VCC = 5 V
R
=10kΩ, C
Load
V
icm=VCC
T=25°C, VCC=5V
Amplitude (V)
Load
/2, ACL=−10
=100pF,
V
out
V
in
Ω
/2
PP
Time (µs)
10/23 Doc ID 17117 Rev 1
Page 11
TSV6290, TSV6290A, TSV6291, TSV6291A Electrical characteristics
Ω
Ω
THD + N (%)
Frequency (Hz)
Figure 13. Distortion + noise vs. output
voltage at V
THD + N (%)
Output voltage (Vrms)
CC
Ω
=1.8V
Ω
Figure 15. Distortion + noise vs. frequency at
V
=1.8V
CC
Figure 14. Distortion + noise vs. output
voltage at VCC=5V
Ω
THD + N (%)
Ω
Ouput voltage (V
)
rms
Figure 16. Distortion + noise vs. frequency at
VCC=5V
Ω
THD + N (%)
Ω
Frequency (Hz)
Doc ID 17117 Rev 1 11/23
Page 12
Application information TSV6290, TSV6290A, TSV6291, TSV6291A
3 Application information
3.1 Operating voltages
The TSV6290 and TSV6291 can operate from 1.5 to 5.5 V. Their parameters are fully
specified for 1.8, 3.3 and 5 V power supplies. However, the parameters are very stable in the
full V
1.5 V. Additionally, the main specifications are guaranteed in extended temperature ranges
from -40° C to +125° C.
3.2 Rail-to-rail input
The TSV6290 and TSV6291 are built with two complementary PMOS and NMOS input
differential pairs. The devices have a rail-to-rail input, and the input common-mode range is
extended from V
V
degraded (as shown in Figure 17 and Figure 18 for V
Figure 17. Input offset voltage vs. input
common mode at V
range and several characterization curves show the TSV629x characteristics at
CC
-0.1 V to V
-0.7 V. In the transition region, the performance of CMR, SVR, Vio and THD is slightly
CC+
CC-
+0.1 V. The transition between the two pairs appears at
CC+
vs. V
io
icm
).
Figure 18. Input offset voltage vs. input
CC
= 1.5 V
common mode at V
CC
= 5 V
The devices are guaranteed without phase reversal.
3.3 Rail-to-rail output
The operational amplifiers’ output levels can go close to the rails: 35 mV maximum above
and below the rail when connected to a 10 kΩ resistive load to V
3.4 Shutdown function (TSV6290)
The operational amplifier is enabled when the SHDN pin is pulled high. To disable the
amplifier, the SHDN
output is in a high impedance state. The SHDN
V
or V
CC+
12/23 Doc ID 17117 Rev 1
CC-
.
must be pulled down to V
CC-
/2.
CC
. When in shutdown mode, the amplifier’s
pin must never be left floating, but tied to
Page 13
TSV6290, TSV6290A, TSV6291, TSV6291A Application information
The turn-on and turn-off times are calculated for an output variation of ±200 mV (Figure 19
and Figure 20 show the test configurations).
Figure 19. Test configuration for turn-on time
(Vout pulled down)
Figure 20. Test configuration for turn-off time
(Vout pulled down)
+ V
V
CC
- 0.5 V
CC
+
DUT
GND
-
GND
Figure 21. Turn-on time, VCC=5V,
V
pulled down, T = 25° C
out
Shutdown pulse
Vout
Voltage (V)
Vcc = 5V
T = 25°C
+ V
CC
2 KΩ
- 0.5 V
V
CC
+
DUT
GND
2 KΩ
-
GND
Figure 22. Turn-off time, V
V
pulled down, T = 25° C
out
Output voltage (V)
=5V,
CC
Shutdown pulse
Vcc = 5V
T = 25°C
Vout
Time( s)
Doc ID 17117 Rev 1 13/23
Page 14
Application information TSV6290, TSV6290A, TSV6291, TSV6291A
3.5 Optimization of DC and AC parameters
These devices use an innovative approach to reduce the spread of the main DC and AC
parameters. An internal adjustment achieves a very narrow spread of the current
consumption (29 µA typical, min/max at ±17%). Parameters linked to the current
consumption value, such as GBP, SR and A
, benefit from this narrow dispersion.
Vd
3.6 Driving resistive and capacitive loads
These products are micropower, low-voltage operational amplifiers optimized to drive rather
large resistive loads, above 5 kΩ. For lower resistive loads, the THD level may significantly
increase.
The amplifiers have a relatively low internal compensation capacitor, making them very fast
while consuming very little. They are ideal when used in a non-inverting configuration or in
an inverting configuration in the following conditions.
● IGainI ≥ 3 in an inverting configuration (C
(CL = 100 pF, RL = 100 kΩ)
● Gain ≥ +4 in a non-inverting configuration (C
(CL = 100 pF, RL= 100 kΩ)
As these operational amplifiers are not unity gain stable, for a low closed-loop gain it is
recommended to use the TSV62x (29 µA, 420 kHz) or TSV63x (60 µA, 880 kHz) which are
unity gain stable.
Table 8. Related products
= 20 pF, RL = 100 kΩ) or IgainI ≥ 10
L
= 20 pF, RL = 100 kΩ) or gain ≥ +11
L
Part # Icc (µA) at 5 V GBP (MHz) SR (V/µs)
TSV620-1 29 0.42 0.14 1
TSV6290-1 29 1.3 0.5 +11
TSV630-1 60 0.88 0.34 1
TSV6390-1 60 2.4 1.1 +11
3.7 PCB layouts
For correct operation, it is advised to add 10 nF decoupling capacitors as close as possible
to the power supply pins.
3.8 Macromodel
An accurate macromodel of the TSV6290 and TSV6291 is available on STMicroelectronics’
web site at www.st.com. This model is a trade-off between accuracy and complexity (that is,
time simulation) of the TSV629x operational amplifiers. It emulates the nominal
performances of a typical device within the specified operating conditions mentioned in the
datasheet. It helps to validate a design approach and to select the right operational
amplifier, but it does not replace on-board measurements.
Minimum gain for
stability
(C
= 100 pF)
Load
14/23 Doc ID 17117 Rev 1
Page 15
TSV6290, TSV6290A, TSV6291, TSV6291A Package information
4 Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK
®
packages, depending on their level of environmental compliance. ECOPACK®
®
is an ST trademark.
Doc ID 17117 Rev 1 15/23
Page 16
Package information TSV6290, TSV6290A, TSV6291, TSV6291A
4.1 SOT23-5 package mechanical data
Figure 23. SOT23-5L package mechanical drawing
Table 9. SOT23-5L package mechanical data
Dimensions
Ref.
Min. Typ. Max. Min. Typ. Max.
A 0.90 1.20 1.45 0.035 0.047 0.057
A1 0.15 0.006
A2 0.90 1.05 1.30 0.035 0.041 0.051
B 0.35 0.40 0.50 0.013 0.015 0.019
C 0.09 0.15 0.20 0.003 0.006 0.008
D 2.80 2.90 3.00 0.110 0.114 0.118
D1 1.90 0.075
e 0.95 0.037
E 2.60 2.80 3.00 0.102 0.110 0.118
F 1.50 1.60 1.75 0.059 0.063 0.069
L 0.10 0.35 0.60 0.004 0.013 0.023
K 0° 10°
Millimeters Inches
16/23 Doc ID 17117 Rev 1
Page 17
TSV6290, TSV6290A, TSV6291, TSV6291A Package information
4.2 SOT23-6 package mechanical data
Figure 24. SOT23-6L package mechanical drawing
Table 10. SOT23-6L package mechanical data
Dimensions
Ref.
Min. Typ. Max. Min. Typ. Max.
A 0.90 1.45 0.035 0.057
A1 0.10 0.004
A2 0.90 1.30 0.035 0.051
b 0.35 0.50 0.013 0.019
c 0.09 0.20 0.003 0.008
D 2.80 3.05 0.110 0.120
E 1.50 1.75 0.060 0.069
e 0.95 0.037
H 2.60 3.00 0.102 0.118
L 0.10 0.60 0.004 0.024
° 0 10°
Millimeters Inches
Doc ID 17117 Rev 1 17/23
Page 18
Package information TSV6290, TSV6290A, TSV6291, TSV6291A
4.3 SC70-5 (or SOT323-5) package mechanical data
Figure 25. SC70-5 (or SOT323-5) package mechanical drawing
DIMENSIONS IN MM
GAUGE PLANE
SEATING PLANE
SIDE VIEW
COPLANAR LEADS
TOP VI EW
Table 11. SC70-5 (or SOT323-5) package mechanical data
Dimensions
Ref
Min Typ Max Min Typ Max
A 0.80 1.10 0.315 0.043
A1 0.10 0.004
A2 0.80 0.90 1.00 0.315 0.035 0.039
b 0.15 0.30 0.006 0.012
c 0.10 0.22 0.004 0.009
D 1.80 2.00 2.20 0.071 0.079 0.087
E 1.80 2.10 2.40 0.071 0.083 0.094
E1 1.15 1.25 1.35 0.045 0.049 0.053
e 0.65 0.025
e1 1.30 0.051
L 0.26 0.36 0.46 0.010 0.014 0.018
<0
° 8°
Millimeters Inches
18/23 Doc ID 17117 Rev 1
Page 19
TSV6290, TSV6290A, TSV6291, TSV6291A Package information
4.4 SC70-6 (or SOT323-6) package mechanical data
Figure 26. SC70-6 (or SOT323-6) package mechanical drawing
Table 12. SC70-6 (or SOT323-6) package mechanical data
Dimensions
Ref
Min. Typ. Max. Min. Typ. Max.
A 0.80 1.10 0.031 0.043
A1 0.10 0.004
A2 0.80 1.00 0.031 0.039
b 0.15 0.30 0.006 0.012
c 0.10 0.18 0.004 0.007
D 1.80 2.20 0.071 0.086
E 1.15 1.35 0.045 0.053
e 0.65 0.026
HE 1.80 2.40 0.071 0.094
L 0.10 0.40 0.004 0.016
Q1 0.10 0.40 0.004 0.016
Millimeters Inches
Doc ID 17117 Rev 1 19/23
Page 20
Package information TSV6290, TSV6290A, TSV6291, TSV6291A
Figure 27. SC70-6 (or SOT323-6) package footprint
20/23 Doc ID 17117 Rev 1
Page 21
TSV6290, TSV6290A, TSV6291, TSV6291A Ordering information
5 Ordering information
Table 13. Order codes
Part number
TSV6290ILT
TSV6290ICT SC70-6 K16
TSV6290AILT SOT23-6 K139
TSV6290AICT SC70-6 K39
TSV6291ILT SOT23-5 K107
TSV6291ICT SC70-5 K14
TSV6291AILT SOT23-5 K113
TSV6291AICT SC70-5 K15
Temperature
range
-40°C to +125°C
Package Packing Marking
SOT23-6
Tape & reel
K106
Doc ID 17117 Rev 1 21/23
Page 22
Revision history TSV6290, TSV6290A, TSV6291, TSV6291A
6 Revision history
Table 14. Document revision history
Date Revision Changes
04-Mar-2010 1 Initial release.
22/23 Doc ID 17117 Rev 1
Page 23
TSV6290, TSV6290A, TSV6291, TSV6291A
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 17117 Rev 1 23/23
Loading...