Datasheet TS78M05CP Specification

Page 1
TO-252
Pin
Definition
:
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
(DPAK)
1. Input
2. Ground (tab)
3. Output
General Description
The TS78M00 Series positive voltage regulators are identical to the popular TS7800 Series devices, except that they are specified for only half the output current. Like the TS7800 devices, the TS78M00 Series 3-Terminal regulators are intended for local, on-card voltage regulation. Internal current limiting, thermal shutdown circuitry and safe-area compensation for the internal pass transistor combine to make these devices remarkably rugged under most operating conditions. Maximum output current with adequate heatsink is 500mA
Features
Output Voltage Range 5 to 24V
Output current up to 500mA
No external components required
Internal thermal overload protection
Internal short-circuit current limiting
Output transistor safe-area compensation
Output voltage offered in 4% tolerance
Standard Application Circuit
Ordering Information
Part No. Package
TS78MxxCP RO TO-252 2.5Kpcs / 13” Reel TS78MxxCP ROG TO-252 2.5Kpcs / 13” Reel
Note: “G” denotes Halogen Free Product. Note: Where xx denote voltage option, available are:
05=5V, 08=9V, 09=9V, 12=12V, 15=15V, 18=18V, 24=24V
Absolute Maximum Rating
Parameter Symbol Limit Unit
Input Voltage VIN* 35 V Input Voltage VIN** 40 V Power Dissipation PD Internal Limited W Operating Junction Temperature TJ 0~+125
Storage Temperature Range T Thermal Resistance - Junction to Case RӨJC 10 Thermal Resistance - Junction to Ambient RӨJA 100
Note: * TS78M05 to TS78M18 ** TS78M24 *** Follow the derating curve
Packing
(Ta = 25oC unless otherwise noted)
A common ground is required between the input and the output voltages. The input voltage must remain typically
2.0V above the output voltage even during the low point on the Input ripple voltage. XX = these two digits of the type number indicate voltage.
* = Cin is required if regulator is located an appreciable
distance from power supply filter. ** = Co is not needed for stability; however, it does improve transient response.
-65~+150
STG
o o
o
C
o
C C/W C/W
1/8
Version: D13
Page 2
Temperature Coefficient of
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
TS78M05 Electrical Characteristics
(Vin=10V, Iout=350mA, 0oCTj125oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter Symbol Test Condition Min Typ Max Unit
Tj=25oC
Output voltage Vout
Line Regulation REGline Tj=25oC
Load Regulation REGload Tj=25oC Quiescent Current Iq Iout=0, Tj=25oC -- 3 6 Quiescent Current Change Iq Output Noise Voltage Vn 10Hzf100KHz, Tj=25oC -- 40 -- µV
Ripple Rejection Ratio RR f=120Hz, 8VVin18V 62 78 -- dB Voltage Drop Vdrop Iout=500mA, Tj=25oC -- 2 -- V Output Resistance Rout f=1KHz -- 17 -- m Output Short Circuit Current Peak Output Current Io peak Tj=25oC -- 0.7 -- A
Ios Tj=25oC -- 50 -- mA
7.5VVin20V, 5mAIout350mA
7.5VVin25V -- 3 100 8VVin12V -- 1 50 5mAIout500mA -- 15 100 5mAIout200mA -- 5 50
7.5VVin25V -- -- 0.8 5mAIout350mA -- -- 0.5
4.80 5 5.20
4.75 5 5.25
mV
mA
V
Output Voltage
∆Vout/ ∆Tj Iout= 5mA, 0oCTj125oC -- -0.2 -- mV/ oC
TS78M08 Electrical Characteristics
Vin=14V, Iout=350mA, 0oCTj125oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter Symbol Test Condition Min Typ Max Unit
Tj=25oC
Output voltage Vout
Line Regulation REGline Tj=25oC
Load Regulation REGload Tj=25oC Quiescent Current Iq Iout=0, Tj=25oC -- 3 6 Quiescent Current Change Iq Output Noise Voltage Vn 10Hzf100KHz, Tj=25oC -- 52 -- µV
Ripple Rejection Ratio RR f=120Hz, 11VVin21V 56 80 -- dB Voltage Drop Vdrop Iout=500mA, Tj=25oC -- 2 -- V Output Resistance Rout f=1KHz -- 16 -- m Output Short Circuit Current Ios Tj=25oC -- 50 -- mA Peak Output Current Io peak Tj=25oC -- 0.7 -- A Temperature Coefficient of Output Voltage
Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as
possible, and thermal effects must be taken into account separately.
This specification applies only for DC power dissipation permitted by absolute maximum ratings.
∆Vout/ ∆Tj Iout= 5mA, 0oCTj125oC -- -0.2 -- mV/ oC
10.5VVin23V, 5mAIout350mA
10.5VVin25V -- 6 160 11VVin17V -- 2 80 5mAIout500mA -- 12 160 5mAIout200mA -- 4 80
10.5VVin25V -- -- 0.8 5mAIout350mA -- -- 0.5
7.69 8 8.32
7.61 8 8.40
V
mV
mA
2/8
Version: D13
Page 3
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
TS78M09 Electrical Characteristics
(Vin=15V, Iout=350mA, 0oCTj125oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter Symbol Test Condition Min Typ Max Unit
Tj=25oC 8.65 9 9.36
Output Voltage Vout
Line Regulation REGline Tj=25oC
Load Regulation REGload Tj=25oC Quiescent Current Iq Iout=0, Tj=25oC -- 3 6 Quiescent Current Change Iq Output Noise Voltage Vn 10Hzf100KHz, Tj=25oC -- 52 -- uV
Ripple Rejection Ratio RR f=120Hz, 12VVin22V 55 80 -- dB Voltage Drop Vdrop Iout=500mA, Tj=25oC -- 2 -- V Output Resistance Rout f=1KHz -- 16 -- m Output Short Circuit Current Ios Tj=25oC -- 50 -- mA Peak Output Current Io peak Tj=25oC -- 0.7 -- A Temperature Coefficient of Output Voltage
∆Vout/ ∆Tj Iout= 5mA, 0oCTj125oC -- -0.2 -- mV/ oC
11.5VVin23V, 5mAIout350mA
11.5VVin26V -- 6 180 12VVin17V -- 2 90 5mAIout500mA -- 12 180 5mAIout200mA -- 4 90
11.5VVin26V -- -- 0.8 5mAIout350mA -- -- 0.5
8.57 9 9.45
mV
mA
V
TS78M12 Electrical Characteristics
(Vin=19V, Iout=350mA, 0oCTj125oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter Symbol Test Condition Min Typ Max Unit
Tj=25oC 11.53
Output Voltage Vout
Line Regulation REGline Tj=25oC
Load Regulation REGload Tj=25oC Quiescent Current Iq Tj=25oC, Iout=0 -- 3 6 Quiescent Current Change Iq Output Noise Voltage Vn 10Hzf100KHz, Tj=25oC -- 75 -- uV
Ripple Rejection Ratio RR f=120Hz, 15VVin25V 55 80 -- dB Voltage Drop Vdrop Iout=500mA, Tj=25oC -- 2 -- V Output Resistance Rout f=1KHz -- 18 -- m Output Short Circuit Current Ios Tj=25oC -- 50 -- mA Peak Output Current Io peak Tj=25oC -- 0.7 -- A Temperature Coefficient of Output Voltage
Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as
possible, and thermal effects must be taken into account separately.
This specification applies only for DC power dissipation permitted by absolute maximum ratings.
∆Vout/ ∆Tj Iout=5mA, 0oCTj125oC -- -0.3 -- mV/ oC
14.5VVin27V, 5mAIout350mA
14.5VVin30V -- 10 240 15VVin19V -- 3 120 5mAIout500mA -- 12 240 5mAIout200mA -- 4 120
14.5VVin30V -- -- 0.8 5mAIout500mA -- -- 0.5
11.42
12 12.48 12 12.60
V
mV
mA
3/8
Version: D13
Page 4
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
TS78M15 Electrical Characteristics
(Vin=23V, Iout=350mA, 0oCTj125oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter Symbol Test Condition Min Typ Max Unit
Tj=25oC 14.42
Output voltage Vout
Line Regulation REGline Tj=25oC
Load Regulation REGload Tj=25oC Quiescent Current Iq Tj=25oC, Iout=0 -- 3 6 Quiescent Current Change Iq Output Noise Voltage Vn 10Hzf100KHz, Tj=25oC -- 90 -- µV
Ripple Rejection Ratio RR f=120Hz, 18VVin28V 54 80 -- dB Voltage Drop Vdrop Iout=500mA, Tj=25oC -- 2 -- V Output Resistance Rout f=1KHz -- 19 -- m Output Short Circuit Current Ios Tj=25oC -- 50 -- mA Peak Output Current Io peak Tj=25oC -- 0.7 -- A Temperature Coefficient of Output Voltage
∆Vout/ ∆Tj Iout=10mA, 0oCTj125oC -- -0.3 -- mV/ oC
17.5VVin30V, 5mAIout350mA
17.5VVin30V -- 12 300 18VVin22V -- 3 150 5mAIout500mA -- 12 300 5mAIout200mA -- 4 150
17.5VVin30V -- -- 0.8 5mAIout500mA -- -- 0.5
14.28
15 15.60 15 15.75
mV
mA
V
TS78M18 Electrical Characteristics
(Vin=24V, Iout=350mA, 0oCTj125oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter Symbol Test Condition Min Typ Max Unit
Tj=25oC
Output Voltage Vout
Line Regulation REGline Tj=25oC
Load Regulation REGload Tj=25oC Quiescent Current Iq Tj=25oC, Iout=0 -- 3 6 Quiescent Current Change Iq Output Noise Voltage Vn 10Hzf100KHz, Tj=25oC -- 110 -- uV
Ripple Rejection Ratio RR f=120Hz, 21VVin31V 54 80 -- dB Voltage Drop Vdrop Iout=500mA, Tj=25oC -- 2 -- V Output Resistance Rout f=1KHz -- 22 -- m Output Short Circuit Current Ios Tj=25oC -- 50 -- mA Peak Output Current Io peak Tj=25oC -- 0.7 -- A Temperature Coefficient of Output Voltage
Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as
possible, and thermal effects must be taken into account separately.
This specification applies only for DC power dissipation permitted by absolute maximum ratings.
∆Vout/ ∆Tj Iout= 5mA, 0oCTj125oC -- -0.5 -- mV/ oC
21VVin33V, 5mAIout350mA
21VVin33V -- 15 360 22VVin26V -- 5 180 5mAIout500mA -- 12 360 5mAIout200mA -- 4 180
21VVin33V -- -- 0.8 5mAIout500mA -- -- 0.5
17.30
17.14
18 18.72 18 18.90
V
mV
mA
4/8
Version: D13
Page 5
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
TS78M24 Electrical Characteristics
Vin=33V, Iout=350mA, 0oCTj125oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter Symbol Test Condition Min Typ Max Unit
Tj=25oC
Output voltage Vout
Line Regulation REGline Tj=25oC
Load Regulation REGload Tj=25oC Quiescent Current Iq Iout=0, Tj=25oC -- 3 6 Quiescent Current Change Iq Output Noise Voltage Vn 10Hzf100KHz, Tj=25oC -- 170 -- µV
Ripple Rejection Ratio RR f=120Hz, 27VVin37V 54 80 -- dB Voltage Drop Vdrop Iout=500mA, Tj=25oC -- 2 -- V Output Resistance Rout f=1KHz -- 28 -- m Output Short Circuit Current Ios Tj=25oC -- 50 -- mA Peak Output Current Io peak Tj=25oC -- 0.7 -- A Temperature Coefficient of Output Voltage
Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as
possible, and thermal effects must be taken into account separately.
This specification applies only for DC power dissipation permitted by absolute maximum ratings.
∆Vout/ ∆Tj Iout= 5mA, 0oCTj125oC -- -0.5 -- mV/ oC
27VVin38V, 5mAIout350mA
27VVin38V -- 18 480 28VVin32V -- 6 240 5mAIout500mA -- 12 480 5mAIout200mA -- 4 240
27VVin38V -- -- 0.8 5mAIout500mA -- -- 0.5
23.07
22.85
24 24.96 24 25.20
V
mV
mA
5/8
Version: D13
Page 6
Electrical Characteristics Curve
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
Figure 1. Bias Current vs. Input Voltage
Figure 3. Bias Current vs. Output Current
Figure 2. Dropout Voltage vs.
Junction Temperature
Figure 4. Ripple Rejection vs. Frequency
Figure 6. Peak Output Current vs. Dropout
Voltage
6/8
Version: D13
Page 7
= Output Voltage
= Year Code
= Month Code
= Lot Code
= Package Code for TO
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
TO-252 Mechanical Drawing
Marking Diagram
XX
(05=5V, 08=8V, 09=9V, 12=12V, 15=15V, 18=18V, 24=24V)
Y M
(A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep,
J=Oct, K=Nov, L=Dec)
= Month Code for Halogen Free Product
(O=Jan, P=Feb, Q=Mar, R=Apl, S=May, T=Jun, U=Jul, V=Aug, W=Sep,
X=Oct, Y=Nov, Z=Dec)
L CP
-252
Unit: Millimeters
7/8
Version: D13
Page 8
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
Notice
Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies.
Information contained herein is intended to provide a product description only. No license, express or implied, to any intellectual property rights is granted by this document. Except as provided in TSC’s terms and conditions of sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale.
8/8
Version: D13
Page 9
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Taiwan Semiconductor: TS78M08CP TS78M18CP TS78M24CP TS78M09CP TS78M15CP TS78M12CP TS78M05CP
Loading...