Datasheet THS6072CDGNR, THS6072CDGN, THS6072CD, THS6072IDR, THS6072IDGNR Datasheet (Texas Instruments)
...Page 1
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
D
ADSL Differential Receiver
– Ideal for Central Office or Remote
T erminal Applications
D
Low 3.4 mA Per Channel Quiescent Current
D
10 nV/√Hz Voltage Noise
D
Very Low Distortion
– THD = –79 dBc (f = 1 MHz, R
L
= 1 kΩ)
D
High Speed
– 175 MHz Bandwidth (–3 dB, G = 1)
– 230 V/µs Slew Rate
D
High Output Drive, IO = 85 mA (typ)
D
Wide Range of Power Supplies
– VCC = ±5 V to ±15 V
D
Available in Standard SOIC or MSOP
PowerPAD Package
D
Evaluation Module Available
description
The THS6072 is a high-speed, low-power differential receiver designed for ADSL communication systems. Its
low 3.4-mA per channel quiescent current reduces power to half that of other ADSL receivers making it ideal
for low power ADSL applications. This receiver operates with a very low distortion of –79 dBc
(f = 1 MHz, R
L
= 1 kΩ). The THS6072 is a voltage feedback amplifier offering a high 175-MHz bandwidth and
230-V/µs slew rate and is unity gain stable. It operates over a wide range of power supply voltages including
±4.5 V to ±15 V. This device is available in a standard SOIC or MSOP PowerPAD package.
HIGH-SPEED xDSL LINE DRIVER/RECEIVER FAMILY
DEVICE
DRIVER RECEIVER 5 V ±5 V ±15 V DESCRIPTION
THS6002
•
• • • 500-mA differential line driver and receiver
THS6012 • • • 500-mA differential line driver
THS6022 • • • 250-mA differential line driver
THS6032 • • • 500-mA low-power ADSL central-office line driver
THS6062 • • • • Low-noise ADSL receiver
THS6072 • • • Low-power ADSL receiver
THS7002 • • • Low-noise programmable-gain ADSL receiver
PowerPAD is a trademark of Texas Instruments.
Copyright 2000, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Cross Section View Showing
PowerPAD Option (DGN)
1
2
3
4
8
7
6
5
1OUT
1IN–
1IN+
V
CC–
VCC+
2OUT
2IN–
2IN+
THS6072
D OR DGN PACKAGE
(TOP VIEW)
CAUTION: The THS6072 provides ESD protection circuitry. However , permanent damage can still occur if this device is subjected
to high-energy electrostatic discharges. Proper ESD precautions are recommended to avoid any performance degradation or loss
of functionality.
Page 2
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
AVAILABLE OPTIONS
PACKAGED DEVICES
T
A
NUMBER OF
CHANNELS
PLASTIC
SMALL OUTLINE
†
(D)
PLASTIC
MSOP
†
(DGN)
MSOP
SYMBOL
EVALUATION
MODULE
0°C to 70°C 2 THS6072CD THS6072CDGN AHZ THS6072EVM
–40°C to 85°C 2 THS6072ID THS6072IDGN AIA —
†
The D and DGN packages are available taped and reeled. Add an R suffix to the device type (i.e., THS6072CDGN).
functional block diagram
1OUT
1IN–
1IN+
V
CC
2OUT
2IN–
2IN+
–V
CC
Figure 1. THS6072 – Dual Channel
Page 3
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature (unless otherwise noted)
†
Supply voltage, VCC ±16.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage, VI ±V
CC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output current, IO 150 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential input voltage, V
IO
±4 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum junction temperature, TJ 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature, TA: C-suffix 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I-suffix –40°C to 85°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature, T
stg
–65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 300°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATING TABLE
θ
θ
T
= 25°C
PACKAGE
JA
(°C/W)
JC
(°C/W)
A
POWER RATING
D 167
‡
38.3 740 mW
DGN
§
58.4 4.7 2.14 W
‡
This data was taken using the JEDEC standard Low-K test PCB. For the JEDEC Proposed
High-K test PCB, the θJA is 95°C/W with a power rating at TA = 25°C of 1.32 W.
§
This data was taken using 2 oz. trace and copper pad that is soldered directly to a 3 in. × 3 in.
PC. For further information, refer to
Application Information
section of this data sheet.
recommended operating conditions
MIN NOM MAX UNIT
pp
Dual supply ±4.5 ±16
Suppl
y v
oltage, V
CC+
and V
CC–
Single supply 9 32
V
p
p
C-suffix 0 70
°
Operating free-air temperature, T
A
I-suffix –40 85
°C
Page 4
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at TA = 25°C, VCC = ±15 V, RL = 150 Ω (unless otherwise noted)
dynamic performance
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
VCC = ±15 V
175
VCC = ±5 V
Gain
=
1
160
MH
z
Small-signal bandwidth (–3 dB)
VCC = ±15 V
70
VCC = ±5 V
Gain
= –
1
65
MHzBW
VCC = ±15 V
35
Bandwidth for 0.1 dB flatness
VCC = ±5 V
Gain
=
1
35
MH
z
p
V
O(pp)
= 20 V, VCC = ±15 V 2.7
Full power bandwidth
†
V
O(pp)
= 5 V, VCC = ±5 V 7.1
MH
z
VCC = ±15 V , 20-V step Gain = 5 230
SR
Slew rate
‡
VCC = ±5 V, 5-V step Gain = 1 170
V/µs
VCC = ±15 V , 5-V step
43
Settling time to 0.1%
VCC = ±5 V, 2-V step
Gain
= –
1
30
ns
t
s
VCC = ±15 V , 5-V step
233
Settling time to 0.01%
VCC = ±5 V, 2-V step
Gain
= –
1
280
ns
†
Slew rate is measured from an output level range of 25% to 75%.
‡
Full power bandwidth = slew rate/2π V
O(Peak)
.
noise/distortion performance
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Vpp = 2 V,
VCC = ±15 V RL = 1 kΩ –79
THD
Total harmonic distortion
O( )
,
f = 1 MHz, Gain = 2
VCC = ±5 V RL = 1 kΩ –77
dBc
V
n
Input voltage noise VCC = ±5 V or ±15 V, f = 10 kHz 10 nV/√Hz
I
n
Input current noise VCC = ±5 V or ±15 V, f = 10 kHz 0.7 pA/√Hz
X
T
Channel-to-channel crosstalk VCC = ±5 V or ±15 V, f = 1 MHz –75 dB
dc performance
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
TA = 25°C 10 19
p
p
V
CC
=
±15 V
,
V
O
=
±10 V
,
R
L
= 1
kΩ
TA = full range 9
V/mV
Open loop gain
TA = 25°C 8 16
V
CC
= ±5 V,
V
O
= ±2.5 V,
R
L
=
250 Ω
TA = full range 7
V/mV
p
TA = 25°C 1 7
VOSInput offset voltage
TA = full range 8
mV
Offset voltage drift TA = full range 15 µV/°C
p
VCC = ±5 V or ±15 V
TA = 25°C 1.2 6
IIBInput bias current
TA = full range 8
µ
A
p
TA = 25°C 20 250
IOSInput offset current
TA = full range 400
nA
Offset current drift TA = full range 0.3 nA/°C
Page 5
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at TA = 25°C, VCC = ±15 V , RL = 150 Ω (unless otherwise noted) (continued)
input characteristics
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
p
VCC = ±15 V ±13.8 ±14.1
V
ICR
Common-mode input voltage range
VCC = ±5 V ±3.8 ±3.9
V
VCC = ±15 V , V
ICR
= ±12 V , TA = full range 78 93 dB
CMRR
Common mode rejection ratio
VCC = ±5 V, V
ICR
= ±2 V, TA = full range 84 90 dB
R
I
Input resistance 1 MΩ
C
I
Input capacitance 1.5 pF
output characteristics
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
VCC = ±15 V RL = 250 Ω ±12 ±13.6
p
VCC = ±5 V RL = 150 Ω ±3.4 ±3.8
V
VOOutput voltage swing
VCC = ±15 V
±13 ±13.8
VCC = ±5 V
R
L
= 1
kΩ
±3.5 ±3.9
V
VCC = ±15 V
65 85
I
O
Output
curren
t
†
VCC = ±5 V
R
L
= 20
Ω
50 70
mA
I
SC
Short-circuit current
†
VCC = ±15 V 100 mA
R
O
Output resistance Open loop 13 Ω
†
Observe power dissipation ratings to keep the junction temperature below the absolute maximum rating when the output is heavily loaded or
shorted. See the absolute maximum ratings section of this data sheet for more information.
power supply
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
pp
p
Dual supply ±4.5 ±16.5
VCCSuppl
y v
oltage operating range
Single supply 9 33
V
TA = 25°C 3.4 4.2
pp
p
p
V
CC
=
±15 V
TA = full range 5
ICCSupply current (per amplifier)
TA = 25°C 2.9 3.7
mA
V
CC
= ±5
V
TA = full range 4.5
PSRR Power supply rejection ratio VCC = ±5 V or ±15 V TA = full range 79 90 dB
‡
Full range = 0°C to 70°C for C suffix and –40°C to 85°C for I suffix
§
Slew rate is measured from an output level range of 25% to 75%.
¶
Full power bandwidth = slew rate/2π V
O(Peak)
.
Page 6
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 2
–20.00
0.00
20.00
40.00
60.00
80.00
100.00
OPEN LOOP GAIN
& PHASE RESPONSE
vs
FREQUENCY
f – Frequency – Hz
100 1k 1G1M 10M
Phase
100M100k10k
Open Loop Gain – dB
VCC = ±5 V and ±15 V
Gain
45°
0°
–45°
90°
135°
180°
–225°
Phase Responce
Figure 3
–80
–60
–40
–20
0
20
CROSSTALK
vs
FREQUENCY
VCC = ±15 V
Gain = 1
RF = 0 Ω
RL = 150 Ω
f – Frequency – Hz
100k 1M 1G10M 100M
Crosstalk – dB
Figure 4
–100
–90
–80
–70
–60
–50
–40
10.00 100.00 1000.00
TOTAL HARMONIC DISTORTION
vs
FREQUENCY
f - Frequency - Hz
10M100k 1M
THD - Total Harmonic Distortion - dBc
VCC = ± 15 V
Gain = 2
V
O(PP)
= 2 V
RL = 150 Ω
RL = 1 kΩ
Figure 5
–100
–90
–80
–70
–60
–50
–40
10.00 100.00 1000.00
TOTAL HARMONIC DISTORTION
vs
FREQUENCY
f - Frequency - Hz
10M100k 1M
THD - Total Harmonic Distortion - dBc
VCC = ± 5 V
Gain = 2
V
O(PP)
= 2 V
RL = 150 Ω
RL = 1 kΩ
Figure 6
10
50
90
130
170
210
250
290
330
2345
SETTLING
vs
OUTPUT STEP
VCC = ±5 V(0.01%)
VO – Output Step Voltage – V
Settling Time – ns
VCC = ±15 V(0.01%)
VCC = ±5 V(0.1%)
VCC = ±15 V(0.1%)
–100
–80
–60
–40
–20
0
Figure 7
POWER SUPPLY REJECTION
RATIO
vs
FREQUENCY
f - Frequency - Hz
PSRR - Power Supply Rejection Ratio - dB
VCC = ± 15 V & ± 5 V
100M10M100k 1M
–V
CC
+V
CC
Figure 8
–100
–90
–80
–70
–60
–50
0 5 10 15 20
DISTORTION
vs
OUTPUT VOLTAGE
VO – Output Voltage – V
Distortion – dBc
VCC = ± 15 V
RL = 1 kΩ
Gain = 5
f = 1 MHz
2nd Harmonic
3rd Harmonic
Figure 9
–100
–90
–80
–70
–60
–50
0 5 10 15 20
DISTORTION
vs
OUTPUT VOLTAGE
VO – Output Voltage – V
Distortion – dBc
VCC = ± 15 V
RL = 150 Ω
Gain = 5
f = 1 MHz
2nd Harmonic
3rd Harmonic
Page 7
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 10
–100
–90
–80
–70
–60
–50
10.00 100.00 1000.00
DISTORTION
vs
FREQUENCY
f – Frequency – Hz
Distortion – dBc
100k 1M 10M
2nd Harmonic
3rd Harmonic
VCC = ± 15 V
RL = 1 kΩ
Gain = 2
V
O(PP)
= 2 V
Figure 11
–100
–90
–80
–70
–60
–50
10.00 100.00 1000.00
DISTORTION
vs
FREQUENCY
f – Frequency – Hz
Distortion – dBc
100k 1M 10M
2nd Harmonic
3rd Harmonic
VCC = ± 5 V
RL = 1 kΩ
Gain = 2
V
O(PP)
= 2 V
Figure 12
–100
–90
–80
–70
–60
–50
10.00 100.00 1000.00
DISTORTION
vs
FREQUENCY
f – Frequency – Hz
Distortion – dBc
100k 1M 10M
2nd Harmonic
3rd Harmonic
VCC = ± 15 V
RL = 150 Ω
Gain = 2
V
O(PP)
= 2 V
Figure 13
–100
–90
–80
–70
–60
–50
10.00 100.00 1000.00
DISTORTION
vs
FREQUENCY
f – Frequency – Hz
Distortion – dBc
100k 1M 10M
2nd Harmonic
3rd Harmonic
VCC = ± 5 V
RL = 150 Ω
Gain = 2
V
O(PP)
= 2 V
Figure 14
OUTPUT AMPLITUDE
vs
FREQUENCY
f - Frequency - Hz
Output Amplitude – dB
–6
–4
–2
0
2
4
10.00 100.00 1000.00 10000.00 100000.00
1G10M100k 1M 100M
RF = 51 Ω
RF = 130 Ω
VCC = ± 15 V
Gain = 1
RL = 150 Ω
V
O(PP)
= 63 mV
RF = 0 Ω
Figure 15
OUTPUT AMPLITUDE
vs
FREQUENCY
f - Frequency - Hz
Output Amplitude – dB
–6
–4
–2
0
2
4
10.00 100.00 1000.00 10000.00 100000.00
1G10M100k 1M 100M
RF = 51 Ω
RF = 130 Ω
VCC = ± 5 V
Gain = 1
RL = 150 Ω
V
O(PP)
= 63 mV
RF = 0 Ω
Figure 16
OUTPUT AMPLITUDE
vs
FREQUENCY
f - Frequency - Hz
Output Amplitude – dB
–8
–6
–4
–2
0
2
10.00 100.00 1000.00 10000.00 100000.00
1G10M100k 1M 100M
RF = 51 Ω
VCC = ± 15 V
Gain = 1
RL = 1 kΩ
V
O(PP)
= 63 mV
RF = 0 Ω
Figure 17
OUTPUT AMPLITUDE
vs
FREQUENCY
f - Frequency - Hz
Output Amplitude – dB
–8
–6
–4
–2
0
2
10.00 100.00 1000.00 10000.00 100000.00
1G10M100k 1M 100M
RF = 51 Ω
VCC = ± 5 V
Gain = 1
RL = 1 kΩ
V
O(PP)
= 63 mV
RF = 0 Ω
Figure 18
OUTPUT AMPLITUDE
vs
FREQUENCY
f - Frequency - Hz
Output Amplitude – dB
–8
–6
–4
–2
0
2
10.00 100.00 1000.00 10000.00 100000.00
1G10M100k 1M 100M
RF = 1 kΩ
RF = 1.3 kΩ
VCC = ± 15 V
Gain = –1
RL = 150 Ω
V
O(PP)
= 63 mV
RF = 2 kΩ
Page 8
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 19
OUTPUT AMPLITUDE
vs
FREQUENCY
f - Frequency - Hz
Output Amplitude – dB
–8
–6
–4
–2
0
2
10.00 100.00 1000.00 10000.00 100000.00
1G10M100k 1M 100M
RF = 1 kΩ
RF = 1.3 kΩ
VCC = ± 5 V
Gain = –1
RL = 150 Ω
V
O(PP)
= 63 mV
RF = 2 kΩ
Figure 20
OUTPUT AMPLITUDE
vs
FREQUENCY
f - Frequency - Hz
Output Amplitude – dB
–8
–6
–4
–2
0
2
10.00 100.00 1000.00 10000.00 100000.00
1G10M100k 1M 100M
RF = 1.3 kΩ
RF = 1.5 kΩ
VCC = ± 15 V
Gain = –1
RL = 1 kΩ
V
O(PP)
= 63 mV
RF = 2 kΩ
Figure 21
OUTPUT AMPLITUDE
vs
FREQUENCY
f - Frequency - Hz
Output Amplitude – dB
–8
–6
–4
–2
0
2
10.00 100.00 1000.00 10000.00 100000.00
1G10M100k 1M 100M
RF = 1.3 kΩ
VCC = ± 5 V
Gain = –1
RL = 1 kΩ
V
O(PP)
= 63 mV
RF = 1.5 kΩ
Figure 22
OUTPUT AMPLITUDE
vs
FREQUENCY
f - Frequency - Hz
Output Amplitude – dB
–2
0
2
4
6
8
10.00 100.00 1000.00 10000.00 100000.00
1G10M100k 1M 100M
RF = 1.5 kΩ
RF = 750 Ω
VCC = ± 15 V
Gain = 2
RL = 150 Ω
V
O(PP)
= 126 mV
RF = 1.2 kΩ
Figure 23
OUTPUT AMPLITUDE
vs
FREQUENCY
f - Frequency - Hz
Output Amplitude – dB
–2
0
2
4
6
8
10.00 100.00 1000.00 10000.00 100000.00
1G10M100k 1M 100M
RF = 750 Ω
VCC = ± 5 V
Gain = 2
RL = 150 Ω
V
O(PP)
= 126 mV
RF = 1.2 kΩ
RF = 1.5 kΩ
Figure 24
OUTPUT AMPLITUDE
vs
FREQUENCY
f - Frequency - Hz
Output Amplitude – dB
–2
0
2
4
6
8
10.00 100.00 1000.00 10000.00 100000.00
1G10M100k 1M 100M
RF = 1.2 kΩ
VCC = ± 15 V
Gain = 2
RL = 1 kΩ
V
O(PP)
= 126 mV
RF = 1.5 kΩ
Figure 25
OUTPUT AMPLITUDE
vs
FREQUENCY
f - Frequency - Hz
Output Amplitude – dB
–2
0
2
4
6
8
10.00 100.00 1000.00 10000.00 100000.00
1G10M100k 1M 100M
RF = 1.2 kΩ
VCC = ± 5 V
Gain = 2
RL = 1 kΩ
V
O(PP)
= 126 mV
RF = 1.5 kΩ
Figure 26
–1.2
–0.8
–0.4
0.0
0.4
0.8
1.2
0 200 400 600 800 1000
2-V STEP RESPONSE
t - Time - ns
– Output Voltage – V
V
O
VCC = ± 5 V
Gain = 2
RF = 1.2 kΩ
RL = 150 Ω
Figure 27
–3
–2
–1
0
1
2
3
0 200 400 600 800 1000
5-V STEP RESPONSE
t - Time - ns
– Output Voltage – V
V
O
VCC = ± 5 V
Gain = –1
RF = 1.3 kΩ
RL = 150 Ω
Page 9
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 28
–1.2
–1.0
–0.8
–0.6
–0.4
–0.2
–0.0
0.2
0.4
0.6
0.8
1.0
1.2
0 200 400 600 800 1000
2-V STEP RESPONSE
t - Time - ns
– Output Voltage – V
V
O
VCC = ± 15 V
Gain = 2
RF = 1.2 kΩ
RL = 150 Ω
Figure 29
–12
–10
–8
–6
–4
–2
0
2
4
6
8
10
12
0 200 400 600 800 1000
20-V STEP RESPONSE
t - Time - ns
– Output Voltage – V
V
O
VCC = ± 15 V
Gain = 5
RF = 1.2 kΩ
RL = 150 Ω
Figure 30
INPUT OFFSET VOLTAGE
vs
FREE-AIR TEMPERATURE
TA - Free-Air Temperature - °C
V
IO
– Input Offset Voltage – mV
0.3
0.5
0.7
0.9
1.1
1.3
1.5
–40 –20 0 20 40 60 80 100
VCC = ± 15 V
VCC = ± 5 V
Figure 31
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
–40 –20 0 20 40 60 80 100
INPUT BIAS CURRENT
vs
FREE-AIR TEMPERATURE
TA - Free-Air Temperature - °C
VCC = ±15 V
– Input Bias Current –
I
IB
µA
VCC = ± 5 V
Figure 32
3
5
7
9
11
13
15
579111315
OUTPUT VOLTAGE
vs
SUPPLY VOLTAGE
±VCC - Supply Voltage - V
TA=25°C
O
- Output Voltage -V
V
RL = 150 Ω
RL = 1 kΩ
Figure 33
3
5
7
9
11
13
15
579111315
TA=25°C
COMMON-MODE INPUT VOLTAGE
vs
SUPPLY VOLTAGE
±VCC - Supply Voltage - V
– Common-Mode Input Voltage –
V
ICR
± V
Figure 34
1
3
5
7
9
11
13
15
–40 –20 0 20 40 60 80 100
O
– Output Voltage –V
V
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
TA – Free-Air Temperature – _C
VCC = ± 5 V
RL = 150 Ω
VCC = ± 5 V
RL = 1 kΩ
VCC = ± 15 V
RL = 150 Ω
VCC = ± 15 V
RL = 1 kΩ
Figure 35
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
579111315
TA=85°C
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
± VCC - Supply Voltage - V
I
CC
– Supply Current – mA
TA=–40°C
TA=25°C
Figure 36
0.1
1
10
100
VOLTAGE & CURRENT NOISE
vs
FREQUENCY
f - Frequency - Hz
100 1k 10k10 100k
nV/
Hz
– Voltage Noise –V
n
I
n
– Current Noise – pA/
Hz
VCC = ± 15 V and ± 5 V
TA = 25°C
V
N
I
N
Page 10
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
ADSL line noise
Per ANSI T1.413, the noise power spectral density for an ADSL line is –140 dBm/√Hz. This results in a voltage
noise requirement of less than 31.6 nV/√Hz for the receiver in an ADSL system with a 1:1 transformer ratio.
Noise Power Spectral Density = –140 dBm/√Hz
Power = 1e–17 × 1 Hz = 0.01 fW
Assume: RL = 100 Ω
V
noise
= √(P×R) = √(0.01 fW × 100 Ω) = 31.6 nV/√Hz
For ADSL systems that use a 1:2 transformer ratio, such as central office line cards, the voltage noise
requirement for the receiver is lowered to 15.8 nV/√Hz.
TRANSFORMER
RATIO
V
noise
ON LINE
1:1 31.6 nV/√Hz
1:2 15.8 nV/√Hz
The THS6072 was designed to operate with 10 nV/√Hz voltage noise, exceeding the noise requirements for
an ADSL system operating with 1:1 or 1:2 transformer ratios. For systems where a voltage noise of less than
10 nV/√Hz
voltage noise is required, see the THS6062 low noise ADSL receiver which operates with a voltage
noise level of 1.6 nV/√Hz.
minimizing distortion
One way to minimize distortion is to increase the load impedance seen by the amplifier, thereby reducing the
currents in the output stage. This will help keep the output transistors in their linear amplification range and will
also reduce the heating effects. This can be seen in Figure 10 through Figure 13, which show a 1-kΩ load
distortion is much better than a 150-Ω load.
Page 11
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
_
+
1 kΩ
2 kΩ
V
IN+
_
+
1 kΩ
V
IN–
+
–
1 kΩ
1 kΩ
2 kΩ
12.5 Ω
+
–
1 kΩ
1 kΩ
2 kΩ
1:2
To Telephone Line
12.5 Ω
Receiver 1
Receiver 2
V
OUT+
V
OUT–
100 Ω
Driver 1
Driver 2
THS6032
THS6072
Figure 37. Typical ADSL Central Office Application
_
+
1 kΩ
2 kΩ
V
IN+
_
+
1 kΩ
1 kΩ
V
IN–
+
–
1 kΩ
1 kΩ
2 kΩ
50 Ω
+
–
1 kΩ
1 kΩ
2 kΩ
1:1
To Telephone Line
50 Ω
Receiver 1
Receiver 2
V
OUT+
V
OUT–
100 Ω
Driver 1
Driver 2
THS6022
THS6072
Figure 38. Typical ADSL Remote Terminal Application
Page 12
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
theory of operation
The THS6072 is a high-speed, operational amplifier configured in a voltage feedback architecture. It is built
using a 30-V , dielectrically isolated, complementary bipolar process with NPN and PNP transistors possessing
fTs of several GHz. This results in an exceptionally high performance amplifier that has a wide bandwidth, high
slew rate, fast settling time, and low distortion. A simplified schematic is shown in Figure 39.
IN– (2)
IN+ (3)
NULL (1) NULL (8)
(6) OUT
(4) VCC–
(7) VCC+
Figure 39. THS6072 Simplified Schematic
noise calculations and noise figure
Noise can cause errors on very small signals. This is especially true when amplifying small signals, where
signal-to-noise ratio (SNR) is very important. The noise model for the THS6072 is shown in Figure 40. This
model includes all of the noise sources as follows:
• e
n
= Amplifier internal voltage noise (nV/√Hz)
• IN+ = Noninverting current noise (pA/√Hz)
• IN– = Inverting current noise (pA/√Hz)
• e
Rx
= Thermal voltage noise associated with each resistor (eRx = 4 kTRx)
Page 13
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
noise calculations and noise figure (continued)
_
+
R
F
R
S
R
G
e
Rg
e
Rf
e
Rs
e
n
IN+
Noiseless
IN–
e
ni
e
no
Figure 40. Noise Model
The total equivalent input noise density (eni) is calculated by using the following equation:
eni+ǒe
n
Ǔ
2
)
ǒ
IN
)
R
S
Ǔ
2
)ǒIN–
ǒRFø
R
G
Ǔ
Ǔ
2
)
4kTRs)
4kTǒRFø
R
G
Ǔ
Ǹ
Where:
k = Boltzmann’s constant = 1.380658 × 10
–23
T = Temperature in degrees Kelvin (273 +°C)
RF || RG = Parallel resistance of RF and R
G
To get the equivalent output noise of the amplifier, just multiply the equivalent input noise density (eni) by the
overall amplifier gain (AV).
eno+
eniAV+
e
ni
ǒ
1
)
R
F
R
G
Ǔ
(noninverting case)
As the previous equations show, to keep noise at a minimum, small value resistors should be used. As the
closed-loop gain is increased (by reducing RG), the input noise is reduced considerably because of the parallel
resistance term. This leads to the general conclusion that the most dominant noise sources are the source
resistor (RS) and the internal amplifier noise voltage (en). Because noise is summed in a root-mean-squares
method, noise sources smaller than 25% of the largest noise source can be effectively ignored. This can greatly
simplify the formula and make noise calculations much easier to calculate.
For more information on noise analysis, please refer to the
Noise Analysis
section in
Operational Amplifier
Circuits Applications Report
(literature number SLVA043).
Page 14
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
14
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
noise calculations and noise figure (continued)
This brings up another noise measurement usually preferred in RF applications, the noise figure (NF). Noise
figure is a measure of noise degradation caused by the amplifier. The value of the source resistance must be
defined and is typically 50 Ω in RF applications.
NF+10log
ȧ
ȧ
ȱ
Ȳ
e
2
ni
ǒ
e
Rs
Ǔ
2
ȧ
ȧ
ȳ
ȴ
Because the dominant noise components are generally the source resistance and the internal amplifier noise
voltage, we can approximate the noise figure as:
NF+10log
ȧ
ȧ
ȧ
ȧ
ȧ
ȱ
Ȳ
1
)
ȧ
ȡ
Ȣ
ǒ
e
n
Ǔ
2
)ǒIN
)
R
S
Ǔ
2
ȧ
ȣ
Ȥ
4kTR
S
ȧ
ȧ
ȧ
ȧ
ȧ
ȳ
ȴ
Figure 41 shows the noise figure graph for the THS6072.
0.00
5.00
10.00
15.00
20.00
25.00
30.00
35.00
40.00
Source Resistance – RS (Ω)
f = 10 kHz
TA = 25°C
NOISE FIGURE
vs
SOURCE RESISTANCE
10 100 1k 10k
Noise Figure (dB)
100k
Figure 41. Noise Figure vs Source Resistance
Page 15
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
driving a capacitive load
Driving capacitive loads with high performance amplifiers is not a problem as long as certain precautions are
taken. The first is to realize that the THS6072 has been internally compensated to maximize its bandwidth and
slew rate performance. When the amplifier is compensated in this manner, capacitive loading directly on the
output will decrease the device’s phase margin leading to high frequency ringing or oscillations. Therefore, for
capacitive loads of greater than 10 pF, it is recommended that a resistor be placed in series with the output of
the amplifier, as shown in Figure 42. A minimum value of 20 Ω should work well for most applications. For
example, in 75-Ω transmission systems, setting the series resistor value to 75 Ω both isolates any capacitance
loading and provides the proper line impedance matching at the source end.
+
_
THS6072
C
LOAD
1.3 kΩ
Input
Output
1.3 kΩ
20 Ω
Figure 42. Driving a Capacitive Load
offset voltage
The output offset voltage, (VOO) is the sum of the input offset voltage (VIO) and both input bias currents (IIB) times
the corresponding gains. The following schematic and formula can be used to calculate the output offset
voltage:
VOO+
V
IO
ǒ
1
) ǒ
R
F
R
G
Ǔ
Ǔ
"
I
IB
)
R
S
ǒ
1
) ǒ
R
F
R
G
Ǔ
Ǔ
"
I
IB–RF
+
–
V
I
+
R
G
R
S
R
F
I
IB–
V
O
I
IB+
Figure 43. Output Offset Voltage Model
Page 16
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
16
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
general configurations
When receiving low-level signals, limiting the bandwidth of the incoming signals into the system is often
required. The simplest way to accomplish this is to place an RC filter at the noninverting terminal of the amplifier
(see Figure 44).
V
I
V
O
C1
+
–
R
G
R
F
R1
f
–3dB
+
1
2pR1C1
V
O
V
I
+ ǒ
1
)
R
F
R
G
Ǔ
ǒ
1
1)sR1C1
Ǔ
Figure 44. Single-Pole Low-Pass Filter
Page 17
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
circuit layout considerations
To achieve the levels of high frequency performance of the THS6072, follow proper printed-circuit board high
frequency design techniques. A general set of guidelines is given below. In addition, a THS6072 evaluation
board is available to use as a guide for layout or for evaluating the device performance.
D
Ground planes – It is highly recommended that a ground plane be used on the board to provide all
components with a low inductive ground connection. However, in the areas of the amplifier inputs and
output, the ground plane can be removed to minimize the stray capacitance.
D
Proper power supply decoupling – Use a 6.8-µF tantalum capacitor in parallel with a 0.1-µF ceramic
capacitor on each supply terminal. It may be possible to share the tantalum among several amplifiers
depending on the application, but a 0.1-µF ceramic capacitor should always be used on the supply terminal
of every amplifier. In addition, the 0.1-µF capacitor should be placed as close as possible to the supply
terminal. As this distance increases, the inductance in the connecting trace makes the capacitor less
effective. The designer should strive for distances of less than 0.1 inches between the device power
terminals and the ceramic capacitors.
D
Sockets – Sockets are not recommended for high-speed operational amplifiers. The additional lead
inductance in the socket pins will often lead to stability problems. Surface-mount packages soldered directly
to the printed-circuit board is the best implementation.
D
Short trace runs/compact part placements – Optimum high frequency performance is achieved when stray
series inductance has been minimized. To realize this, the circuit layout should be made as compact as
possible, thereby minimizing the length of all trace runs. Particular attention should be paid to the inverting
input of the amplifier. Its length should be kept as short as possible. This will help to minimize stray
capacitance at the input of the amplifier.
D
Surface-mount passive components – Using surface-mount passive components is recommended for high
frequency amplifier circuits for several reasons. First, because of the extremely low lead inductance of
surface-mount components, the problem with stray series inductance is greatly reduced. Second, the small
size of surface-mount components naturally leads to a more compact layout, thereby minimizing both stray
inductance and capacitance. If leaded components are used, it is recommended that the lead lengths be
kept as short as possible.
general PowerPAD design considerations
The THS6072 is available packaged in a thermally-enhanced DGN package, which is a member of the
PowerP AD family of packages. This package is constructed using a downset leadframe upon which the die is
mounted [see Figure 45(a) and Figure 45(b)]. This arrangement results in the lead frame being exposed as a
thermal pad on the underside of the package [see Figure 45(c)]. Because this thermal pad has direct thermal
contact with the die, excellent thermal performance can be achieved by providing a good thermal path away
from the thermal pad.
The PowerP AD package allows for both assembly and thermal management in one manufacturing operation.
During the surface-mount solder operation (when the leads are being soldered), the thermal pad can also be
soldered to a copper area underneath the package. Through the use of thermal paths within this copper area,
heat can be conducted away from the package into either a ground plane or other heat dissipating device.
The PowerP AD package represents a breakthrough in combining the small area and ease of assembly of the
surface mount with the, heretofore, awkward mechanical methods of heatsinking.
Page 18
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
18
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
general PowerPAD design considerations (continued)
DIE
Side View (a)
End View (b) Bottom View (c)
DIE
Thermal
Pad
NOTE A: The thermal pad is electrically isolated from all terminals in the package.
Figure 45. Views of Thermally Enhanced DGN Package
Although there are many ways to properly heatsink this device, the following steps illustrate the recommended
approach.
Thermal pad area (68 mils x 70 mils) with 5 vias
(Via diameter = 13 mils)
Figure 46. PowerPAD PCB Etch and Via Pattern
1. Prepare the PCB with a top side etch pattern as shown in Figure 46. There should be etch for the leads as
well as etch for the thermal pad.
2. Place five holes in the area of the thermal pad. These holes should be 13 mils in diameter. Keep them small
so that solder wicking through the holes is not a problem during reflow.
3. Additional vias may be placed anywhere along the thermal plane outside of the thermal pad area. This helps
dissipate the heat generated by the THS6072DGN IC. These additional vias may be larger than the 13-mil
diameter vias directly under the thermal pad. They can be larger because they are not in the thermal pad
area to be soldered, so wicking is not a problem.
4. Connect all holes to the internal ground plane.
5. When connecting these holes to the ground plane, do not use the typical web or spoke via connection
methodology . Web connections have a high thermal resistance connection that is useful for slowing the heat
transfer during soldering operations. This makes the soldering of vias that have plane connections easier.
In this application, however , low thermal resistance is desired for the most efficient heat transfer. Therefore,
the holes under the THS6072DGN package should make their connection to the internal ground plane with
a complete connection around the entire circumference of the plated-through hole.
6. The top-side solder mask should leave the terminals of the package and the thermal pad area with its five
holes exposed. The bottom-side solder mask should cover the five holes of the thermal pad area. This
prevents solder from being pulled away from the thermal pad area during the reflow process.
7. Apply solder paste to the exposed thermal pad area and all of the IC terminals.
8. With these preparatory steps in place, the THS6072DGN IC is simply placed in position and run through
the solder reflow operation as any standard surface-mount component. This results in a part that is properly
installed.
Page 19
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
general PowerPAD design considerations (continued)
The actual thermal performance achieved with the THS6072DGN in its PowerPAD package depends on the
application. In the example above, if the size of the internal ground plane is approximately 3 inches × 3 inches,
then the expected thermal coefficient, θJA, is about 58.4_C/W. For comparison, the non-PowerPAD version of
the THS6072 IC (SOIC) is shown. For a given θJA, the maximum power dissipation is shown in Figure 47 and
is calculated by the following formula:
PD+
ǒ
T
MAX–TA
q
JA
Ǔ
Where:
PD= Maximum power dissipation of THS6072 IC (watts)
T
MAX
= Absolute maximum junction temperature (150°C)
T
A
= Free-ambient air temperature (°C)
θ
JA
= θ
JC
+ θ
CA
θJC= Thermal coefficient from junction to case
θCA= Thermal coefficient from case to ambient air (°C/W)
DGN Package
θJA = 58.4°C/W
2 oz. Trace And Copper Pad
With Solder
DGN Package
θJA = 158°C/W
2 oz. Trace And
Copper Pad
Without Solder
SOIC Package
High-K Test PCB
θJA = 98°C/W
TJ = 150°C
SOIC Package
Low-K Test PCB
θJA = 167°C/W
2
1.5
1
0
–40 –20 0 20 40
Maximum Power Dissipation – W
2.5
3
MAXIMUM POWER DISSIPATION
vs
FREE-AIR TEMPERATURE
3.5
60 80 100
0.5
TA – Free-Air Temperature – °C
NOTE A: Results are with no air flow and PCB size = 3”× 3”
Figure 47. Maximum Power Dissipation vs Free-Air Temperature
More complete details of the PowerP AD installation process and thermal management techniques can be found
in the Texas Instruments Technical Brief,
PowerPAD Thermally Enhanced Package.
This document can be
found at the TI web site (www.ti.com) by searching on the key word PowerPAD. The document can also be
ordered through your local TI sales office. Refer to literature number SLMA002 when ordering.
Page 20
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
20
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
general PowerPAD design considerations (continued)
The next consideration is the package constraints. The two sources of heat within an amplifier are quiescent
power and output power. The designer should never forget about the quiescent heat generated within the
device, especially multiamplifier devices. Because these devices have linear output stages (Class A-B), most
of the heat dissipation is at low output voltages with high output currents. Figure 48 and Figure 49 show this
effect, along with the quiescent heat, with an ambient air temperature of 50°C. Obviously, as the ambient
temperature increases, the limit lines shown will drop accordingly . The area under each respective limit line is
considered the safe operating area. Any condition above this line will exceed the amplifier’s limits and failure
may result. When using V
CC
= ±5 V , there is generally not a heat problem, even with SOIC packages. But, when
using
V
CC
= ±15 V , the SOIC package is severely limited in the amount of heat it can dissipate. The other key factor
when looking at these graphs is how the devices are mounted on the PCB. The PowerPAD devices are
extremely useful for heat dissipation. But, the device should always be soldered to a copper plane to fully use
the heat dissipation properties of the PowerPAD. The SOIC package, on the other hand, is highly dependent
on how it is mounted on the PCB. As more trace and copper area is placed around the device, θJA decreases
and the heat dissipation capability increases. The currents and voltages shown in these graphs are for the total
package.
Figure 48
Package With
θJA ≤ 64°C/W
SO-8 Package
θJA = 98°C/W
High-K Test PCB
VCC = ± 5 V
TJ = 150°C
TA = 50°C
Both Channels
100
80
40
0
012 3
– Maximum RMS Output Current – mA
140
180
200
45
160
120
60
20
| VO | – RMS Output Voltage – V
I
O
||
Maximum Output
Current Limit Line
THS6072
MAXIMUM RMS OUTPUT CURRENT
vs
RMS OUTPUT VOLTAGE DUE TO THERMAL LIMITS
SO-8 Package
θJA = 167°C/W
Low-K Test PCB
Safe Operating Area
Figure 49
100
10
0369
1000
12 15
Maximum Output
Current Limit Line
| VO | – RMS Output Voltage – V
– Maximum RMS Output Current – mA
I
O
||
VCC = ± 15 V
TJ = 150°C
TA = 50°C
Both Channels
THS6072
MAXIMUM RMS OUTPUT CURRENT
vs
RMS OUTPUT VOLTAGE DUE TO THERMAL LIMITS
1
SO-8 Package
θJA = 167°C/W
Low-K Test PCB
DGN Package
θJA = 58.4°C/W
Safe Operating Area
SO-8 Package
θJA = 98°C/W
High-K Test PCB
Page 21
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
21
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
evaluation board
An evaluation board is available for the THS6072 (literature number SLOP322). This board has been configured
for very low parasitic capacitance in order to realize the full performance of the amplifier. A schematic of the
evaluation board is shown in Figure 50. The circuitry has been designed so that the amplifier may be used in
either an inverting or noninverting configuration. For more information, please refer to the
THS6072 EVM User’s
Guide
. To order the evaluation board, contact your local TI sales office or distributor.
_
+
THS6072
VCC–
VCC+
C1
6.8 µF
C4
0.1 µF
C2
6.8 µF
C3
0.1 µF
R4
1.3 kΩ
R2
1.3 kΩ
R3
49.9 Ω
R5
49.9 Ω
IN–
IN+
NULL
OUT
NULL
+
+
R3
49.9 Ω
Figure 50. THS6072 Evaluation Board
Page 22
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
22
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL INFORMATION
D (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
4040047/D 10/96
0.228 (5,80)
0.244 (6,20)
0.069 (1,75) MAX
0.010 (0,25)
0.004 (0,10)
1
14
0.014 (0,35)
0.020 (0,51)
A
0.157 (4,00)
0.150 (3,81)
7
8
0.044 (1,12)
0.016 (0,40)
Seating Plane
0.010 (0,25)
PINS **
0.008 (0,20) NOM
A MIN
A MAX
DIM
Gage Plane
0.189
(4,80)
(5,00)
0.197
8
(8,55)
(8,75)
0.337
14
0.344
(9,80)
16
0.394
(10,00)
0.386
0.004 (0,10)
M
0.010 (0,25)
0.050 (1,27)
0°–8°
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
D. Falls within JEDEC MS-012
Page 23
THS6072
LOW-POWER ADSL DIFFERENTIAL RECEIVER
SLOS290A – FEBRUARY 2000 – REVISED APRIL 2000
23
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL INFORMATION
DGN (S-PDSO-G8) PowerPAD PLASTIC SMALL-OUTLINE PACKAGE
0,69
0,41
0,25
Thermal Pad
(See Note D)
0,15 NOM
Gage Plane
4073271/A 01/98
4,98
0,25
5
3,05
4,78
2,95
8
4
3,05
2,95
1
0,38
0,15
0,05
1,07 MAX
Seating Plane
0,10
0,65
M
0,25
0°–6°
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions include mold flash or protrusions.
D. The package thermal performance may be enhanced by attaching an external heat sink to the thermal pad. This pad is electrically
and thermally connected to the backside of the die and possibly selected leads.
E. Falls within JEDEC MO-187
PowerPAD is a trademark of Texas Instruments Incorporated.
Page 24
IMPORTANT NOTICE
T exas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
Customers are responsible for their applications using TI components.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 2000, Texas Instruments Incorporated
Loading...