Datasheet TES225ZG-A, TES225YG-A, TES150ZE-A, TES150YE-A, TES113YD-A Datasheet (Power-One)

(888) IPD-CONVerters

●

[phone]

TES SERIES - 225 WATT

DESCRIPTION FEATURES

●

www.ipdconverters.com

TES single output DC/DC converters provide up to
225 Watts of output power at up to 45 Amperes of
output current in an industry standard “3/4 brick”
package. The TES converters feature open-frame
packaging, along with planar magnetics and a high
efficiency topology, to provide maximum useable
power density. The TES converters use 100% surface­mount construction and are fully compatible with
production board washing processes.

TECHNICAL SPECIFICATIONS

Input

Voltage Range

24 VDC Nominal 18 - 36 VDC
48 VDC Nominal 36 - 72 VDC

Output

Setpoint Accuracy ±1 %
Line Regulation Vin Min. - Vin Max., I
Load Regulation I
Remote Sense Headroom 0.5 VDC
Minimum Output Current 10 % I
Dynamic Regulation, Loadstep 25% I

Pk Deviation 4% V

Settling Time 500 µs
Voltage Trim Range ±10%
Current Limit Type Latch

Current Limit Threshold Range, % of I
Short Circuit Threshold Range, % of I
OVP Trip Range 115 - 140% V
UVP Trip Range 70 - 90% V

OVP/UVP Type Latch

Turn-On Time 10 ms
Remote Shutdown Positive Logic

Remote Shutdown Reference Vin Negative
Switching Frequency 5V

Isolation

Input - Output 1500 VDC
Input - Case 1050 VDC

Output - Case 500 VDC
Temperature Coefficient ±0. 02%/°C
Case Temperature

Operating Range -40 To +100°C

Storage Range -40 To +125°C
Thermal Shutdown Range 105 to 115°C
Vibration, 3 Axes, 5 Min Each 5 g, 10 - 55 Hz
MTBF† (Bellcore TR-NWT-000332) 1.0 X 106 hrs
Safety UL, CUL, TUV
Weight (Approx.) 3.3 oz

Min. - I

out

out

/ 3.3V & 2.5V

out

Rated 0.2% V

out

Max., Vin Nom. 0.5% V

Rated

out

Rated 110 - 140%

out

Rated 200%

out

General

out

300 kHz / 200 kHz

out
out

Nom.
Nom.

out
out

out
out

• 45A “3/4 Brick”

• Very High Efficiency

• Open-Frame Packaging

• 100°C Baseplate
Operation

Efficiency vs. Load (48V Input)

95
90
85
80
75
70

EFFICIENCY %

65
60
55

10 20 30 40 50 60 70 80 90 100

†

MTBF predictions may vary slightly from model to model.
Specifications typically at 25°C, normal line, and full load, unless otherwise stated.
Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with

commercial wave-soldering equipment.
Safety: Agency approvals may vary from model to model. Please consult factory

for specific model information.

• Planar Magnetics

• Low Voltage Outputs

• 1500V Isolation

• Synchronous
Rectification

TES150ZE-A

EFF. (36v)
EFF. (48v)
EFF. (75v)

LOAD %

Notes

C-52

TES SERIES - 225 WATT

MODELS - (See the last page of this file for options.)

Vin

(Volts)

24

24

24

48
48

48

Vin Range

(Volts)

18 - 36

18 - 36

18 - 36

36 - 72
36 - 72

36 - 72

Iin Max.*

(Amps)

8.0

10.2

14.6

4.0

5.1

7.2

Denotes advanced product release. Consult factory for product availability.

* Maximum input current at minimum input voltage, maximum rated output power.

** At nominal Vin, rated output.

MECHANICAL DRAWING

2.40"

MOUNTING INSERTS
M3X.5 THROUGH 4PL

2.650"(67.3mm)

2.250"(57.2mm)

1.500"(38.1mm)

1

2

(61.0mm)

Vout

(Volts)

2.5

3.3

5

2.5

3.3

5

Iout Rated

(Amps)

45

45

45

45
45

45

Rip ple & Noi se

Pk-Pk (mV)

100

100

100

100
100

100

Effici ency

Typ. **

79%

82%

82%

80%
83%

82%

Model

TES113YD-A

TES150YE-A

TES225YG-A

TES113ZD-A
TES150ZE-A

TES225ZG-A

Thermal Impedance

Natural Convection 5.7 °C/W
100 LFM 3.9 °C/W
200 LFM 2.6 °C/W
300 LFM 1.9 °C/W
400 LFM 1.7 °C/W

7

8

2.400"(61.0mm)

2.100"(53.3mm)

Note:
Thermal impedance data is dependent on
many environmental factors. The exact
thermal performance should be validated for
specific application.

0.750"(19.1mm)

-0.400"(-10.2mm)

-0.60"(-15.2mm)

0.18"(4.6mm)

0.50"

(12.7mm)

(0.6mm)

0

(-5.1mm)

.025"

-0.20"

3

4

0

BOTTOM VIEW

(25.4mm)

DIA 0.040"

(1.0mm)

1.000"

65

1.200"
(30.5mm)

9

10

11

12

13

2.000"

(50.8mm)

0.900"(22.9)

0.600"(15.2)

0.350"(8.9mm)

0.100"(2.5mm)

-0.150"(-3.8mm)

DIA 0.080"

(2.0mm)

3.45"

(87.6mm)

Pin Function

1 -V
2 Enable

in

3 Case
4 +V
5 CN2 (opt.)

in

6 CN1 (opt.)
7 +V
8 +V
9 -V
10 -V
11 -Sense

out

out
out
out

12 Trim
13 +Sense

T olerances

Inches: (Millimeters)
.XX ± 0.020 .X ± 0.5
.XXX ± 0.010 .XX ± 0.25

Pin:
± 0.002 ± 0.05

( Dimensions as listed unless otherwise
specified.)

C-53

OPTIONS

When ordering equipment options, use the following suffix information. Select the option(s) that
you prefer and add them to the model number. Example ordering options are located below the
options table.

OPTION SUFFIX APPLICABLE SERIES REMARKS

Negative Logic N HA S , HBD, HBS, HES, LES, QBS,

Lucent Compatible Trim T HAS, HBD, HBS, HES, QBS, QES
Terminal Strip TS XWS, XWD, XWT
Trim 1 IAS, LES
Enable 2 IAD, IAS, LES, SMS
Trim and Enable 3 IAS, LES
Current Share 4 SMS
Headerless Y Encapsulated EWS, IWS, OWS

PIN LENGTH AND HEATSINK
OPTIONS

0.110” (2.8mm) Pin Length 8 All Units (Except SMS)

0.150” (3.8mm) Pin Length 9 All Units (Except SMS)

0.24” (6.1mm) Horizontal Heatsink 1H All Units (Except DIP, SIP, and SM

0.24” (6.1mm) Vertical Heatsink 1V All Units (Except DIP, SIP, and SM

0.45” (11.4mm) Horizontal
Heatsink

0.45” (11.4mm) Vertical Heatsink 2V All Units (Except DIP, SIP, and SM

0.95” (24.1mm) Horizontal
Heatsink

0.95” (24.1mm) Vertical Heatsink 3V All Units (Except DIP, SIP, and SM

2H All Units (Except DIP, SIP, and SM

3H All Units (Except DIP, SIP, and SM

QES, TES, TQD

Packages)

Packages)

Packages)

Packages)

Packages)

Packages)

TTL “Low” Turns Module ON
TTL “High” Turns Module OFF

Standard Pin Length is 0.180”
(4.6mm)

Includes Thermal Pad

Includes Thermal Pad

Includes Thermal Pad

Includes Thermal Pad

Includes Thermal Pad

Includes Thermal Pad

Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and

0.95” vertical heatsink.
LES015YJ-3N = LES015YJ with optional trim and enable, negative logic.
QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length.

NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems,

equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc.

TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the

date manufactured. Specifications are subject to change without notice.

C105